• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.434-434
• /
• 2000

It is the main problem to measure the position and orientation of a robot end effector for the calibration of robots. The calibration methods can be used as a tool to improve the accuracy of robots without change of the arm or control architecture of robots. But such calibration methods require the accurate measurements. Dynamic measurement of position and orientation Provides a solution of this problem and improves dynamic accuracy by dynamic calibration o( robots. This paper describes the development o( the laser tracking system capable of determining the static and dynamic performance of industrial robots. The structure and system components are presented and basic experimental results are included to demonstrate the instrument performance. The system can be applied to the remote controlled mobile robots as weil as the calibration of robots.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 학술대회 논문집 정보 및 제어부문
• /
• pp.523-525
• /
• 2004

Over the last few years, the control of bipedal robot has been considered a promising research field in the community of robotics. But the problems we encounter make the control of a bipedal robot a hard task. The complicated link connection of the bipedal robot makes it impossible to achieve its exact model. In addition, the joint velocity is needed to accomplish good control performance. In this paper a control method using ANFIS as an system approximator is purposed. First a model biped robot of a biped robot with switching leg influence is presented. Unlike classical method, ANFIS approximation error estimator is inserted in the system for tuning the ANFIS. In the entire system, only ANFIS is used to approximate the uncertain system. ANFIS tuning rule is given combining the observation error, control error and ANFIS approximation error. But this needs velocity information which is not available. So a practical method is newly presented. Finally, computer simulation results is presented to show this control method has good position tracking performance and robustness without need for leg switching acknowledgement.

• 제어로봇시스템학회논문지
• /
• 제22권9호
• /
• pp.716-722
• /
• 2016

Coordinate estimation is an essential function for autonomous navigation of a mobile robot. The optical mouse sensor is convenient and cost-effective for the coordinate estimation problem. It is possible to overcome the position estimation error caused by the slip and the model mismatch of robot's motion equation using the optical mouse sensor. One of the simple methods for the position estimation using the optical mouse sensor is integration of the velocity data from the sensor with time. However, the unavoidable noise in the sensor data may deteriorate the position estimation in case of the simple integration method. In general, a mobile robot has ready-to-use motion information from the encoder sensors of driving motors. By combining the velocity data from the optical mouse sensor and the motion information of a mobile robot, it is possible to improve the coordinate estimation performance. In this paper, a coordinate estimation algorithm for an autonomous mobile robot is presented based on the well-known Kalman filter that is useful to combine the different types of sensors. Computer simulation results show the performance of the proposed localization algorithm for several types of trajectories in comparison with the simple integration method.

• 제어로봇시스템학회논문지
• /
• 제7권6호
• /
• pp.518-522
• /
• 2001

The main problem of the calibration of robots is to measure the position and orientation of a robot end effector. The calibration methods can be used as tool to improve the accuracy of robots without change of the arm or control architecture or robots. But such calibration methods require accurate measurements. Dynamic measurement of position and orientation provides a solution for this problem and improves dynamic accuracy by dynamic calibration of robots. This paper describes the development of the laser tracking system capable of determining the static and dynamic performance of industrial robots. The structure and systems components are presented and basic experimental results are included to demonstrated the instrument performance. The system can be applied to the remote controlled mobile robots as well s the calibration of robots.

• 제어로봇시스템학회논문지
• /
• 제8권11호
• /
• pp.954-962
• /
• 2002

In a park or street, we can see many people jogging or walking with their dogs tracking their masters. In this study, an entertainment robot that imitates a dog's behavior is created. The robot's task is tracking a moving target that is recognized as the master. In order to design the robot, the ecological approach. in which the robot's goals and surroundings heavily influence its design, is used. A three-wheel type locomotion system is designed as the robot's physical structure which can follow a human jogging in outdoor space like a park. A sensor system which can detect the position of a master for the robot in the outdoor space, is developed. This sensor system consists of a signal transmitter which is at the hand of a master and some sensors which are mounted on the robot. The transmitter emits RF(radio frequency) and ultrasonic signals and the sensors detect the direction and distance from the robot to the transmitter by using the received signals. For the control architecture of the robot, a purely reactive behavior-based method is used in order to increase speed of response. The developed robot is evaluated through experiments conducted in indoor and outdoor environments.

• 제어로봇시스템학회논문지
• /
• 제2권1호
• /
• pp.35-44
• /
• 1996

A design method for a teleoperator robot system is presented in this paper. The control system consists of two phases; approach phase and contact one. The end-effector position of the estimated slave robot and the contact force between the end-effector and wall are displayed on the monitors at control site, using which the operator controls the teleoperator system. The approach phase controller is designed using Smith's principle and the contact one designed based upon the structured singular value ${\mu}$ in order to increase the robustness of the system. The uncertainatices such as communication time delay and the variations of system parameters are considered as a muliplicative pertubation. Computer simulations are conducted in order to evaluate the performance of the proposed design method. It is found that desirable control performance, especially in the contact phase, is obtained if the control mode is switched into contact phase when the estimated position of the slave robot end-effector is in front of the wall.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1990년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 26-27 Oct. 1990
• /
• pp.135-139
• /
• 1990

In general, the control of robot arms falls into two board categories (position control and force control). The joint interpolated trajectory schemes generally interpolate the desired joint path by a class of polynomial functions and generate a sequence of time based control set points for the control of a manipulator from a initial location to its destination. A digital position controller was designed and adapted to the industrial balancing manipulator. And also, the joint interpolated trajectory using 3rd order polynomial was generated in this study. The IBM PC used as the main controller and the trajectory planner had enough run-time capabilities. The 8097BH microcontroller is an integral pan of the joint controller which directly controls an axis of motion. The PI servo control system to treat each joint of the robot arm as a independent joint servo mechanism had satisfying performance, and a sequence of time-based intermediate configurations of the manipulator hand showed good continuity and smoothness on position and velocity of the manipulator's joint coordinates along the trajectory.

• 제어로봇시스템학회논문지
• /
• 제21권6호
• /
• pp.497-502
• /
• 2015

One of the goals in the field of mobile robotics is the development of personal service robots for the elderly which behave in populated environments. In this paper, we describe a security robot system and ongoing research results that minimize the risk of the elderly and the infirm to access an area to enter restricted areas with high potential for falls, such as stairs, steps, and wet floors. The proposed robot system surveys a potential falling area with an equipped laser scanner sensor. When it detects walking in elderly or infirm patients who in restricted areas, the robot calculates the velocity vector, plans its own path to forestall the patient in order to prevent them from heading to the restricted area and starts to move along the estimated trajectory. The walking human is assumed to be a point-object and projected onto a scanning plane to form a geometrical constraint equation that provides position data of the human based on the kinematics of the mobile robot. While moving, the robot continues these processes in order to adapt to the changing situation. After arriving at an opposite position to the human's walking direction, the robot advises them to change course. The simulation and experimental results of estimating and tracking of the human in the wrong direction with the mobile robot are presented.

• 산업기술연구
• /
• 제22권B호
• /
• pp.251-260
• /
• 2002

In this thesis, a three degrees of freedom robot, which is able to provide sufficient precision for various robot researches, has been developed. The cable mechanism is used as a basic transmission of robot joints. Based on an optimal design strategy, link and joint parameters are determined and then overall geometry of the robot is designed. As an architecture of robot control, real time control system using real time linux and RtiC-Lab(Real Time Controls Laboratory) is developed. This system, written in C and based on Linux O/S, includes text editor, compiler, downloader, and real time plotter running in host computer for developing control purpose. Using these hardware and software, simple PD position control is implemented, the results shows the effectiveness of the system.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1989년도 한국자동제어학술회의논문집; Seoul, Korea; 27-28 Oct. 1989
• /
• pp.244-249
• /
• 1989

For the robot manipulator in performing precision tasks, it is indispensable that the robot utilize the various sensors for intelligence. In this paper, the hybrid position/force control method is implemented with a force/torque sensor, two personal computers, and a PUMA 560 manipulator. Two application S/W packages for edge following and peg-in-hole tasks are developed by the proposed force control algorithm. The related experimental results are then presented and discussed,