• Journal of Korean Society of Transportation
• /
• v.23 no.4 s.82
• /
• pp.47-55
• /
• 2005

In recent years, the rapid growth of vehicles have increased traffic crashes. Since they can cause the economic losses and have put the life qualify in danger, there should be numerous efforts to reduce traffic crashes. To reduce traffic crashes, this research seeks to improve the safety of intersections by analysing causations of injury severity with Ordered Probability Model. This research applied the Ordered Probit Model, which assumes that ${\epsilon}_i$(random error) is normally distributed, for model calibration and used $p^2$ (likelihood ratio) and $x^2$ (Chi-square) for model selection. The results show that minor road traffic, heavy vehicle rates, major and minor right-turn rates, presence of lightings, speed limits, instructive line for left-turn traffic are significant factors affecting crash severities at signalized intersections.

• Journal of Korean Society of Transportation
• /
• v.25 no.6
• /
• pp.65-77
• /
• 2007

A two-way left-turn lane is a continuous center left-turn lane that could be used as a deceleration and refuge area for both directions of left-turning vehicles. TWLTL's have been used effectively for access management treatment when applied to a highway that has wide-spread left turning traffic demand and a high-density of side streets. In this study, an effective analysis was carried out using a computer-based simulation tool, VISSIM, in order to evaluate performance and safety effects of TWLTLs and develop a warrant. In conclusion, the results indicated that there was a remarkable decrease of through and left-turning vehicle travel time delay on the main road and improvement of traffic safety.

• Journal of Korean Society of Transportation
• /
• v.32 no.4
• /
• pp.389-400
• /
• 2014

This study finds a way to increase the usability of a subway commuter pass. Usability of the commuter pass on a probabilistic statistical model is calculated when the pass is allowed to used in a different mode(bus). A sunk cost of commuter pass is used to reduce the vehicle travels from public transit. 324 people aged 25 to 35 were surveyed and utilized to build a Nested Logit Model on STRADA 3.5 platform. Main results are as follows. First, commuter passes were issued in various forms. Second, the model turns out to be statistically significant in four explanatory variables (discount rate, inter-usablity between modes, forms of payment and periods). Lastly, the more valid on different modes, the more increased of the rail commuter pass.

• International Journal of Highway Engineering
• /
• v.16 no.5
• /
• pp.109-119
• /
• 2014

PURPOSES : The control delay in seconds per vehicle is the most important traffic operational index to evaluate the level of service of signalized intersections. Thus, it is very critical to calculate accurate control delay because it is used as a basic quantitative evidence for decision makings regarding to investments on traffic facilities. The control delay consists of time-in-queue delay, acceleration delay, and deceleration delay so that it is technically difficult to directly measure it from fields. Thus, diverse analysis tools, including CORSIM, SYNCHRO, T7F, VISTRO, etc. have been utilized so far. However, each analysis tool may use a unique methodology in calculating control delays. Therefore, the estimated values of control delays may be different by the selection of an analysis tool, which has provided difficulties to traffic engineers in making solid judgments. METHODS : This study was initiated to verify the feasibility of diverse analysis tools, including HCM methodology, CORSIM, SYNCHRO, T7F, VISTRO, in calculating control delays by comparing estimated control delays with that measured from a field. RESULTS : As a result, the selected tools produced quite different values of control delay. In addition, the control delay value estimated using a calibrated CORSIM model was closest to that measured from the field. CONCLUSIONS : First, through the in-depth experiment, it was explicitly verified that the estimated values of control delay may depend on the selection of an analysis tool. Second, among the diverse tools, the value of control delay estimated using the calibrated microscopic traffic simulation model was most close to that measured from the field. Conclusively, analysts should take into account the variability of control delay values according to the selection of a tool in the case of signalized intersection analysis.

• International Journal of Highway Engineering
• /
• v.18 no.5
• /
• pp.63-73
• /
• 2016

PURPOSES : The objective of this study was to analyze variations in the vehicle driving behavior characteristics on signalized intersections according to the use of traffic enforcement camera (red light camera). METHODS : In order to analyze the driving behavior characteristics on signalized intersections when red light camera are installed, the target sites for investigation were selected depending on whether the red light camera is installed and accident rates increased after the installation. In particular, to analyze the characteristics of dilemma zones in signalized intersections, approach speed and deceleration speed of 3 type vehicles (passing vehicles during a yellow light, stopping at a yellow light, passing vehicles during a green light) were examined. Based on these data, the starting point, ending point, and distance of the dilemma zones were calculated. Also, the locations of increased traffic accidents and decreased accidents after the installation of the equipment were distinguished when analyzing the traffic accident characteristics. RESULTS : Analysis results revealed that there was a tendency for the dilemma zone distance to decrease after the installation of equipment(red light camera) in most sites. This tendency was found to be due to the decrease in the approaching speed of vehicles at intersections after the installation of equipment, resulting in the starting and ending points of dilemma zone to become closer to the stop line. Moreover, analysis showed that the number of traffic accidents decreased for most intersections after the installation of equipment and safety of the intersections increased somewhat. CONCLUSIONS : In general, installation of equipment(red light camera) caused the intersections approaching speed and dilemma zone distance to decrease. Decision-making is difficult for drivers in the dilemma zone, so the decrease in the dilemma zone distance implies an improvement in traffic safety. Furthermore, the number of accidents within intersections significantly decreased after the equipment was installed, leading to the conclusion that installation of the equipment affected the decrease in traffic accidents.

• Journal of Biosystems Engineering
• /
• v.28 no.2
• /
• pp.89-96
• /
• 2003

This study was aimed to identify how the main body vibration of power tiller will be transmitted to the trailer, and to find out the basic information for demage reducing method of agricultural products during transportation. The vertical vibration acceleration level was measured at 6 positions, i.e. engine, hitch, seal and three parts of trailer (front middle, and rear) for the not driving but at the engine speeds of 1,000rpm and driving at 0.35m/s. The results of this research could be summarized as follows; 1. For not driving, the accumulated acceleration level up to 120Hz was 50% of total accelerations at engine part and those were 28~41% at other parts. Those up to 40Hz were 20~30% at engine and hitch part and 2~8% at trailer part. And those up to 20Hz were 13~20% at engine and hitch part and 1~4% at trailer part 2. For the driving with 0.35m/s at paved road, the average vertical accelerations were in the range of 0.005~0.058m/s$^2$. The lowest value of 0.005m/s$^2$ was showed at engine part and the value of 0.031-0.058m/s$^2$ was showed at trailer part. 3. For the driving with 0.35m/s, the accumulated value of average vertical accelerations showed the lowest value at engine parts md showed 5 times value of engine part at trailer part especially highest value at middle part of trailer. 4. For the driving with 0.35m/s, the accumulated acceleration level up to 120Hz was 75% of total accelerations at engine part and those were 20~42% at other parts. Ant those up to 20Hz and 40Hz were 24~26% at engine part and 0.1~0.6% at trailer part.

• Journal of the Korean Society of Safety
• /
• v.32 no.4
• /
• pp.100-106
• /
• 2017

Outline map is used for the description and reconstruction of the traffic accident. One way to produce the outline map is by adopting detailed measurements from the accident site such as final position of the vehicle and pedestrian, width of the road, and locations of the oil and tire marks. This method consumes large amount of time not to mention that of the production of detailed version as fine as the picture of the site. Aerial recording equipment so called HeliCam can produce an outline map that can substitute that of manual method with even faster production time and higher resolution. However, the produced picture have errors which are resulted by distortion due to the characteristics of camera and direction of the photographing. This paper provides correction of the distortion of oultline map produced by HeliCam using Adobe Photoshop and PC-Rect. The result showed resonable error range less than 6 cm(0.1%) for $60m{\times}30m$ area taken by HeliCam. The presented method develops outline map with small error, which is useful to traffic accident analysis, and traffic accident cases analyzed in this study were also.

• Journal of Korean Society for Atmospheric Environment
• /
• v.21 no.6
• /
• pp.699-708
• /
• 2005

To characterize the elemental composition of fine particles in urban area, $PM_{2.5}$ was collected by a 3-stage DRUM impactor at Gwangju during spring and summer. Time and size resolved concentrations for 19 trace elements were obtained by synchrotron X-Ray fluorescence analysis. Trace elements in summer were distributed in smaller size range compared to those in spring. Almost trace element concentrations in fine particles were highly increased during the Asian dust. In spring, soil elements such as Si, K, Ca, Ti and Fe had low enrichment factors indicating the dominant influence of soil dust. However, all elements had high enrichment factors in summer implying that these elements could be emitted from the anthropogenic sources. Factor analysis was conducted with the elemental composition data in order to identify anthropogenic sources of aerosols in urban area during spring and summer. Fine particles in spring have several sources such as soil dust originating from China continental region, coal and oil combustion, biomass burning, sea salt, ferrous and nonferrous metal sources. On the other hand, fine particles in summer were influenced by road dust, gasoline vehicle as well as coal and oil combustion, sea salt, ferrous and nonferrous metal sources.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.2
• /
• pp.64-70
• /
• 2018

Rollover is a major concern for vehicles with a higher center of gravity and for improving driving performance. This study investigates a tilting system to prevent rollover, which was successfully implemented for high-speed trains. It may be useful to apply the concept of the tilting system to a large truck such as a trailer. Even a small adjustment in the tilting angle can improve the driving stability during a steep turn. The equation of motion was derived from a dynamic model of the trailer with the tilting system. The balance of the centrifugal force and normal force determines the rollover critical speed for a given radius of the turn and load. To obtain a more conservative criterion, the rollover critical state was defined as the instant when any side wheel loses contact with the road. To actuate the tilting system, the optimal tilting angle must be calculated from the steering angle and the vehicle speed. Using a simplified model of a large truck, the effects of the tilting angle and load on the rollover critical speed were investigated.

• Journal of Advanced Navigation Technology
• /
• v.15 no.6
• /
• pp.1059-1067
• /
• 2011

Next-Generation ITS environment requires high-speed data packet transmission, security, authentication, and hand-over supportable for driving vehicle on road by installing RSEs and OBUs. Therefore, wireless communication technology for next-generation ITS services are advancing to 200km/h maximum speed supportable, 1km communication radius, minimum 10Mbps hish-speed datarate for multimedia data(such as text, images, movie clips and so on) supportable, high reliability. In this paper, we implemented WAVE communication system which based on IEEE 802.11p PHY/MAC and evaluated that the system meets next-generation ITS environments.