• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.460-465
• /
• 2008

This paper proposes a new type of MR (magentorheological) fluid based suspension system and applies it to military vehicle for vibration control. The suspension system consists of gas spring and MR damper. The nonlinear behavior of spring characteristics is evaluated with respect to the wheel travel and damping force model due to viscosity and yield stress of MR fluid is derived. Subsequently, a military vehicle of 6WD is adopted for the integration of the MR suspension system and its nonlinear dynamic model is establishes by considering vertical, pitch and roll motion. Then, a sky-hook controller associated with semi-active actuating condition is designed to reduce the vibration. In order to demonstrate the effectiveness of the proposed MR suspension system, computer simulation is undertaken showing vibration control performance such as roll angle and pitch angle evaluated under bump and random road profiles.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.6 no.2
• /
• pp.141-149
• /
• 2004

In this study, smoke movement in tunnel fire with natural and longitudinal ventilation systems has been investigated. Reduced-scale experiments were carried out under the Froude scaling using 14.55kW fire source with a wick and experimental data is obtained with 1/18 model tunnel test. Temperature profiles were measured under the ceiling and vertical direction along the center of the tunnel and poisonous gas was measured at emergency exit point. The results show that refuge time for 225m intervals of emergency exit in case of natural ventilation systems is 256 seconds and critical velocity for sufficient back-layer prevention is 2.8m/s for fire strength of 20MW.

• International Journal of Highway Engineering
• /
• v.12 no.2
• /
• pp.123-127
• /
• 2010

In this study, the profiles of optimized rehabilitated section was measured by a lightweight inertial profiler, and pavement smoothness was evaluated. To analyze the repeatability of the used lightweight profiler, two repeatable measurements were conducted. The agreement between two repeatable measurements were evaluated by Cross-correlation function. Pavement smoothness of the optimized rehabilitated pavement section and existing area was compared in terms of International Roughness Index and Profilograh Index. In general, the pavement smoothness of the rehabilitated sections was not good compared to the existing pavement sections. The analysis results could be used for the evaluation of pavement smoothness of the optimized rehabilitated pavement sections.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.1
• /
• pp.17-23
• /
• 2009

This paper proposes a new type of MR(magnetorheological) fluid based suspension system and applies it to military vehicle for vibration control. The suspension system consists of gas spring and MR damper. The nonlinear behavior of spring characteristics is evaluated with respect to the wheel travel and damping force model due to viscosity and yield stress of MR fluid is derived. Subsequently, a military vehicle of 6WD is adopted for the integration of the MR suspension system and its nonlinear dynamic model is established by considering vertical, pitch and roll motion. Then, a sky-hook controller associated with semi-active actuating condition is designed to reduce the imposed vibration. In order to demonstrate the effectiveness of the proposed MR suspension system, computer simulation is undertaken showing vibration control performance such as roll angle and pitch angle evaluated under bump and random road profiles.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.2
• /
• pp.38-46
• /
• 2012

This paper discusses the energy consumption for a mid-size electric vehicle(EV) under various conditions. In order to analyze which driving style is more efficient in terms of the system of the EV, we develop the electric vehicle model and apply several types of speed profiles such as different steady speeds, acceleration/deceleration, and a real world driving cycle including the elevation profile obtained from a GPS device. The results show that the energy consumption of the EV is affected by the operating efficiency of components when driving at low speed, while it depends on required power at wheels when driving at high speed. Also this paper investigates the effect of the elevation of a road and the rate of electrical braking on the energy consumption as well as the fuel economy of a conventional vehicle model under the same conditions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.3
• /
• pp.437-443
• /
• 1987

An optimal design to improve the ride quality was performed with the time and frequency domain analysis based on both of deterministic and random road profiles. The objective function is established to minimize the absorbed power while the constraints are taken so as to satisfy the condition for the stability of vehicle. The result of the optimal design shows that the rms for the acceleration of a driver and his seat is within the critical values for the ride quality from ISO. The optimal values obtained show that the maximum absolute acceleration of the driver and his seat has significantly been reduced and the reference limits on the relative displacement have satisfied their feasibility. As the optimal value according to a specific speed is the results from the optimization process, a global optimum value should be determined to be the one which gives th minimum values of total sum of absorbed power with respect to various speed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.11
• /
• pp.840-845
• /
• 2014

Vibration profiles consist of two kinds of pattern, random and harmonic, at general engineering problems and the detailed vibration test mode of a target system is decided by the spectral condition that is exposed under operation. In moving mobility, random responses come generally from road source; whereas the harmonic responses are triggered from rotating machinery parts, such as combustion engine or drive shaft. Different spectral input may accumulate different damage in frequency domain since the accumulated fatigue damage dependent on the pattern of input spectrum in high cyclic loading condition. To evaluate the sensitivity of spectral damage according to different loading conditions, a linear elastic system is introduced to conduct a uniaxial vibration testing. Measured data, acceleration and strain, is analyzed using energy isocline function and then, the calculated fatigue damage is compared by different loading cases, random and harmonic.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.41 no.1
• /
• pp.51-59
• /
• 2013

This study was conducted to compare the sizes of effective values, which users recognize, according to the kinds of physical and psychological services provided by an arboretum, by estimating them in monetary values. As an analysis tool for this purpose, the CE(Choice Experiments) method, which is able to estimate effective value's size depending on each variable, was employed. For drawing up profiles for estimation of the values of individual services, 25 profiles were extracted using the orthogonal design of the SPSS statistical package, and questions of 75 pairs were created not to make each of the profiles overlapped. Then, each user was given three questions at five sets each and 3,510 data were used for the analysis. As the result, in relation to the attribute, 'The kinds of trees should be diversified 50% more than now.', firstly, users showed the biggest willingness to pay, based on the present level, and expressed intentions to pay 7,956 won, additionally. Secondly, the value of the path design that was unique than the present road design was estimated in 6,025 won, and when individual attendants guided visitors in the arboretum, they expressed intentions to pay nearly three times more expenses than when they were guided as a group. These results show that users in the Gyeongnam Arboretum recognized the highest effective values towards the collection and display of trees that are arboretum's original functions, and it was followed by the unique road design to observe a variety of dense trees well. This research could be useful in comparing or measuring particular effective values of users that central operators of arboretums want to know. Moreover, it would be suggested as an advanced research for providing basic data about value estimation of individual environmental goods not only in arboretums, but also in other fields.

• Journal of Korea Water Resources Association
• /
• v.41 no.8
• /
• pp.773-784
• /
• 2008

The present study was carried out to examine flow properties in linear drainage channels such as road surface drainage facilities. The finite difference formulation for the varied flow analysis was solved for flow profiles in the channels. Starting the first step at the control section, the Newton-Raphson method was applied for producing numerical solutions of the equation. We considered two types of linear drainage channels, a channel with one outlet at downstream end and a channel with two outlets at both ends. Moreover, the flow analysis for various channel slopes was performed. However, we considered channels with the two outlets of slopes satisfying the condition that the both ends are the control section. The maximum of those slopes was decided from the relation between the channel slope and the location of control section. The flow of a channel with one outlet was calculated upward and downward from the control section existing in channel or upward from the control section at downstream end. The flow of a channel with two outlets at both ends were calculated for upstream and downstream channel segments divided by the water dividend, respectively and the flow analysis was completed when the water depth at the water dividend calculated from upstream end was equal to that calculated from downstream end. If the slope was larger than the critical slope, the channel with two outlets was likely to behave like the channel with one outlet. The maximum water depth was investigated and compared with that calculated additionally from the uniform flow analysis. The uniform flow analysis was likely to lead a excessive design of a drainage channel with mild slope.

• International Journal of Highway Engineering
• /
• v.11 no.2
• /
• pp.167-174
• /
• 2009

The simulation of dynamic load was conducted based on surface profile on asphalt concrete pavement, vehicle speeds, and suspension types using a truck simulation program. The results of the simulated dynamic load based on different surface profile, vehicle speeds, and suspension types are analyzed. As pavement roughness and vehicle speed are increased, the dynamic load was increased. Walking beam suspension produces greater dynamic load than air spring suspension. Pavement damage index is calculated based on covariance of dynamic load and Paris-Erdogan fracture parameter, n which is based on creep compliance tests of asphalt mixtures used in Korea. The higher covariance of dynamic load, confidence level, and fracture parameter are used, the greater pavement damage index is obtained. Specification of pavement roughness can be developed in various vehicle speeds and asphalt mixtures, and pay factor can be determined after constructing asphalt concrete pavement using pavement damage concepts.