• Journal of the Korean Society of Safety
• /
• v.26 no.3
• /
• pp.63-68
• /
• 2011

Access-control of hazard zone in a steel manufacturing industry is studied in terms of safety management. Based on the results of risk evaluation for hazard zone, three risk zones with low, middle and high level are categorized. These zones have different color door and locking shape depending on their risk levels. At the high level, red door and key-based locking system are employed to accessed-controled path. Furthermore, tagout, lockout, interlock system for emergency stop, warning and flashing are also introduced. New standardized procedure of access-control for various hazard zones, which could help to greatly contribute to the prevention of accidents in advance, is proposed considering the risk level and the condition of given hazard zones. The standardized procedure of access-management suggested in this study will take an effective role as one of safety guide lines for hazardous workshop of manufacturing industries.

• Geomechanics and Engineering
• /
• v.21 no.3
• /
• pp.289-300
• /
• 2020

Estimating the damage induced by an explosion around a blast hole has always been a challenging issue in geotechnical engineering. It is difficult to determine an exact dimension for damage zone since many parameters are involved in the formation of failures, and there are some uncertainties lying in these parameters. Thus, the present study adopted a probabilistic approach towards this problem. First, a reliability model of the problem was established and the failure probability of induced damage was calculated. Then, the corresponding exceedance risk curve was developed indicating the relation between the failure probability and the cracked zone radius. The obtained risk curve indicated that the failure probability drops dramatically by increasing the cracked zone radius so that the probability of exceedance for any crack length greater than 4.5 m is less than 5%. Moreover, the effect of each parameter involved in the probability of failure, including blast hole radius, explosive density, detonation velocity, and tensile strength of the rock, was evaluated by using a sensitivity analysis. Finally, the impact of the decoupling ratio on the reduction of failures was investigated and the location of its maximum influence was demonstrated around the blast point.

• Journal of Environmental Impact Assessment
• /
• v.9 no.3
• /
• pp.185-202
• /
• 2000

Uncertainty and variability in Life Cycle Assessment(LCA) have been significant key issues in LCA methodology with techniques in other research area such as social and political science. Variability is understood as stemming from inherent variations in the real world, while uncertainty comes from inaccurate measurements, lack of data, model assumptions, etc. Related articles in this issues were reviewed for classification, distinguish and elaboration of probabilistic/stochastic health risk analysis application in LCA. Concept of focal zone, streamlining technique, scenario modelling and Monte Carlo/Latin Hypercube risk analysis were applied to the uncertainty/variability analysis of health risk in LCA. These results show that this general framework of multi-disciplinary methodology between probabilistic health risk assessment and LCA was of benefit to decision making process by suppling information about input/output data sensitivity, health effect priority and health risk distribution. There should be further research needs for case study using this methodology.

• Safety and Health at Work
• /
• v.7 no.4
• /
• pp.389-393
• /
• 2016

Job hazard analyses were conducted to assess exposure to musculoskeletal disorder (MSD) risk factors in seven workers of three dry-cleaning establishments. In accordance with the Washington State Ergonomics Rule, the analyses were performed in two separate steps: (1) observation and checklist approaches were made to identify a "caution zone job" in the seven workers' pressing operations across the three shops; and (2) detailed posture and motion analyses were undertaken to determine a "MSD hazard" in one worker's operation using a video technique. One "caution zone job" was identified and it was the pressing operation job in which five physical risk factors were found in the pressing operations. The detailed analyses confirmed that one "MSD hazard", i.e., awkward posture in shoulders, was prevalent in the pressing operations of the three dry-cleaning facilities. It would be desirable to reduce MSD risk factors including awkward shoulder posture in the dry-cleaning industry.

• Journal of the Korean Society of Safety
• /
• v.31 no.2
• /
• pp.26-32
• /
• 2016

In previous studies on LPG siting in Korea, the scope have not included the probability of the secondary events of adjacent LPG tanks or structures from an explosion source. Therefore, it is essential to first identify the phenomenon which can be caused by BLEVE and then, properly assess their effects to each target including secondary event. In this study, we calculated the effects from a potential BLEVE of 15 ton LPG tank causing damages of storage tanks (LPG), structures and human using Phast ver. 6.7 and then suggested three risk zones (Zone I, II, III) assuming the consequences such as overpressure, heat radiation and missile effect by fragments. Zone I and II are divided at the line of 50% occurrence of the secondary event. Zone II and III are divided by Individual Risk(IR). The zone approach in this study can be used for more effective and safer Land Use Planning (LUP) for the future.

• Fire Science and Engineering
• /
• v.15 no.4
• /
• pp.1-9
• /
• 2001

The purpose of this study is to set up disaster prevention plan and risk assessment system considering combustion velocity at traditional housing zone. The combustion velocity analysis could contribute to build in disaster prevention technique through the potential risk analysis of the area, such analysis also able to set up comprehensive disaster prevention management system. Following results have achieved through the combustion velocity calculation. \circled1 The combustion velocity was calculated in order of the below winds, the above winds and the side winds. \circled2 It must be careful to set up disaster prevention plan in case of the below winds. \circled3 The combustion velocity was calculated at the density Bone where neighboring Distance and Length was small. \circled4 It proved that factors of each parameter not mostly effect to analyse the combustion velocity in limit of the 30 minutes after ignition. \circled5 At the density zone where Distance and Length is small the duration of transfer to neighboring house takes up to 4 minutes, it is required to set up of emergency response plan to minimize the fire dispersion.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.49 no.4
• /
• pp.459-468
• /
• 2013

In the application of the ecosystem-based fisheries assessment Jeonnam marine ranching ecosystem, two fisheries, funnel fishery and trap fishery, were selected as target fisheries. Black seabream, Acanthopagru schlegelii, rock bream, Sebastes inermis, gray mullet, Mugil cephalus, were selected as target species for the funnel fishery, and conger eel, Conger myriaster, was target species for the trap fishery. For assessing indicators of four management objectives, that is the maintenance of sustainability, biodiversity, habitat quality and socio-economic benefits, indicators were selected considering the availability of data, which were 5 indicators for sustainability, 3 indicators for biodiversity, 4 indicators for habitat, 2 indicators for socio-economic benefit. The Objective risk indices for sustainability and biodiversity of two fisheries were estimated at yellow zone, medium risk level. The objective risk indices for habitat and socio-economic benefit were estimated at green zone, safe level. The species risk indices (SRI) were estimated at yellow zone. The fishery risk indices (FRIs) were estimated at 1.143 and 1.400 for funnel net fishery and trap fishery, respectively. Finally the ecosystem risk index estimated at 1.184.

• Journal of Distribution Science
• /
• v.20 no.3
• /
• pp.23-31
• /
• 2022

Purpose: The purpose of this study is to analyze the Safety and Logistical Distribution Management system in Thailand's Highway Work Zone based on data from Logistics drivers. Accidents in highway construction zones have caused enormous casualties in Thailand yearly. Statistical data shows evidence of correlation between numbers of accidents and drivers' recklessness. Research design, data, and methodology: In this study, we conducted an in- depth interview with 414 logistics drivers and highway construction workers in Khon Kaen province, Thailand. The data was collected based on 63 questionnaires aiming at capturing factors contributing to the risk of safety and cause of accidents in logistic infrastructures such as Highway work zone. Results: The result reveals two significant factors affecting safety in highway work zone, which includes construction environment and safety management system. Moreover, the result shows that feeling of afraid and confused while driving within the construction zones significantly affecting driver's risk of having an accident. Conclusions: The findings of this study offer that a strategic planning and evaluation of the logistics drivers' satisfaction and construction workers' participation to mitigate highway accidents at construction zones and that drivers' knowledge and perception toward construction safety management plays a significant role in preventing highway accidents at the construction areas.

• Journal of the Korean Institute of Gas
• /
• v.17 no.6
• /
• pp.83-89
• /
• 2013

Energy industry facilities can cause fatal damage for internal industry employee as well as external general people because handling various kinds of gas and harmful substance might be spread to large scale severe accident by fire, explosion, and toxic gas leakage. In order to prevent these accidents, quantification by damage effect on structure and human is tried by using quantitative risk assessment, but it is difficult to process instantly exceptional cases and requires knowledge of expert. This paper aims to minimize exceptional cases and knowledge of expert, and present risk with human perceptible. So, we designed and developed zone-base risk analysis system that can compute risk of zone in real time at that point using database and incremental model.

• Journal of the Korean Institute of Gas
• /
• v.18 no.1
• /
• pp.52-60
• /
• 2014

This study aims to suggest risk management plan including safety measures through hazard identification followed by consequence analysis in petrochemical plants. Consequence analysis was performed through practical release scenario by using PHAST RISK(ver. 6.7) software in the propylene recovery process(PRP). As results, consequences by fire or explosion accidents in the depropanizer zone, deethanizer zone and heat pump zone were relatively larger than other else zones among six process zones in the PRP. In the case of jet fire, it is recommendable not to install residence building within 200 m of the process zone. Additionally, process zones having large inventory or high pressure must be prevented from accidents and required to establish quick response against accidents.