• Journal of Technologic Dentistry
• /
• v.35 no.2
• /
• pp.127-136
• /
• 2013

Purpose: In order to find out the impact of changes in polymerization conditions of orthodontic acrylic resin on maximum load. Methods: While maintaining mixing ratio 3:1 of polymer and monomer in spray-on way in the production condition of polymerization temperature $25^{\circ}C$ or $37^{\circ}C$ for 10 minutes or 30 minutes of polymerization time by pressure $3kfg/cm^2$ or $6kfg/cm^2$ in the lab maintaining $25^{\circ}C$ of room temperature, the change in maximum load rise rate was tested by producing 5 acrylic resin specimens for orthodontics per group to meet the standards of $25mm{\times}2mm{\times}2mm$ and using INSTRON with the 3rd bar 2mm in diameter and parallel support bending device of $15{\pm}0.1mm$ as test equipment showing 30.00mm/min of crosshead speed, $50{\pm}16$ N/min of load ratio in the laboratory of $24^{\circ}C$ room temperature and as a result, the following results were obtained. Results: 1. When increasing pressure from $3kfg/cm^2$ to $6kfg/cm^2$, maximum load was lowered by -4.285%. 2. When increasing polymerization time from 10 minutes to 30 minutes, maximum load rose by 3.848%. 3. When increasing polymerization temperature from $27^{\circ}C$ to $37^{\circ}C$, maximum load rose by 5.854%. Conclusion: Considering the above test results that polymerization time and polymerization temperature when polymerizing acrylic resin for orthodontics according to changes in working conditions had an impact on the rate of rise of maximum load values but the rate of rise was lowered when increasing pressure from $3kfg/cm^2$ to $6kfg/cm^2$, we came to a conclusion that high pressure more than necessary does not affect the rate of rise of maximum load.

• Fire Science and Engineering
• /
• v.22 no.3
• /
• pp.278-286
• /
• 2008

When big fire in high rise building and multiplex happens, the needs for high prevention system of disaster are being increased for getting the real-time scene state, quick lifesaver, and safe life security. In this paper the proposed evacuation guidance algorithm which analyzed the feature and danger of fire in high rise buildings, gave simplicity and scalability. Our research shows as fire and disaster occur in high rise buildings we construct sensor networks and sense realtime location information on fire alive people, and the situation information for fire instructed quick and safe escaping route by using mesh routing algorithm scheme relative to exit sign.

• KIEAE Journal
• /
• v.13 no.1
• /
• pp.151-157
• /
• 2013

Since high-rise building construction sites are usually located in crowded city areas, sufficient spaces for the inventories of key materials are rarely available. This spatial constraints have been one of the critical challenge that may cause productivity loss and increasing costs of the high-rise building construction projects. The proper material inventory management is certaing a key to the success of high-rise building construction projects as it handles difficulty of securing material stock yards, changes in demands, uncertain delivery time through integrating the construction schedules and actively responding to the key materials attributes. In this light, this research analyzes the latest inventory model, (Q,r) model, in accordance with the high rise building characteristics. This research suggests an optimal inventory management of re-bar considering various demands and lead times. The case study is also presented with regard to the re-bar inventory management.

• Proceedings of the KIEE Conference
• /
• 2006.07e
• /
• pp.27-28
• /
• 2006

This paper deals with an approach to the reduction of potential rise according to the buried depth of structure. In order to analyze the surface potential rise of structure, an electrolytic tank which simulates the semi-infinite earth has been used. The potential rise has been measured and analyzed for types of structure using an electrolytic tank experimental apparatus in real time. The structure models were designed through reducing real buildings and fabricated with two types on a scale of one-one hundred sixty When a test current flowed through structure models, the potential rise of outline frame type(structure model A) was more high than that of electric cage type(structure model B). The distributions of surface potential rise are dependent on the buried depth of structure model.

• Journal of the Korean Institute of Rural Architecture
• /
• v.25 no.2
• /
• pp.9-16
• /
• 2023

This study attempted to analyze the aspect of seeking a characteristic regeneration of low-rise residential areas through the Urban Regeneration New Deal Project in Seohak-dong Art Village in Jeonju, while the urban regeneration new deal projects are being carried out in various regions, nationwide. Time-series changes in aerial photographs in the study area, age, number of floors, and uses of buildings were examined. The main street structure, lots, and changes in buildings were reviewed, and through this, spatial zones that could extract the unique characteristics of the target area were classified. The characteristics of each area was linked to the proposal of an appropriate regeneration plan through the analysis. This study is meaningful in showing a case of characteristics of low-rise residential areas regeneration plan suitable for the specific region while the number of old low-rise residential areas is increasing.

• Proceedings of the KIEE Conference
• /
• 2000.11d
• /
• pp.618-620
• /
• 2000

In case of fire in the high-rise buildings, the appropriate and safe evacuation plans for the building residents are very important to minimize the number of casualties. Since the evacuation time usually depends on the floor plans of the buildings, the evacuation plans should be considered while the architectural design is done. Conventionally, the calculation of the evacuation time in the case of fire breakout is based on the approximate mathematical equations which are prone to error. In this study, the simulator model is developed to help the architectural designers to access the more accurate evacuation time and find out the floor plans which offers the most safe evacuation plans for the residents in case of fire.

• Journal of the Korean Society for Precision Engineering
• /
• v.3 no.1
• /
• pp.29-39
• /
• 1986

An adaptive controller which is robust to the unknown load disturbance is developed for electro-hydraulic speed control systems. Since the load disturbance degrades the performance of the controller such as a steady state error and rise time in the conventional control system, appropriate adjustment of the controller is necessary in order to obtain the desired performances. The adaptation mechanism was designed to tune the feedforward gain, based upon minimization of ITAE (integral of time-multiplied absolute error) performance. The unknown load distrubance was identified by using an analog computer from the relationship between the velocity of the hydraulic motor and the load pressure. To evaluate the performance of the controller a series of simulations and experiments were conducted for various load conditions. Both results show that the proposed adaptive controller shows abetter performance than the conventional controller in terms of the steady state error and rise time.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.308-308
• /
• 2000

In case of fire in the high-rise buildings, the appropriate and safe evacuation plans for the building residents are very important to minimize the number of casualties. Since the evacuation time usually depends on the floor plans of the buildings, the evacuation plans should be considered while the architectural design is done. Conventionally, the calculation of the evacuation time in the case of fire breakout is based on the approximate mathematical equations which are prone to error In this study, the simulator model is developed to help the architectural designers to access the more accurate evacuation time and find out the floor plans which offers the most safe evacuation plans for the residents in case of fire.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.11a
• /
• pp.260-266
• /
• 2001

The surface temperature at the interface of bodies in a sliding contact is one of the most important factors influencing the behavior of machine components. So the calculation of the surface temperature at a sliding contact interface has long been an interesting and important subject for tribologist. Several methods for calculating surface temperature have been devised. Several numerical methods have been used to predict the temperature rise of sliding surface. but those need much time to calculate. In this study to reduce the calculation time the hybrid method using both semi-infinite solid analysis and FVM was used. It is founded that the computing time of hybrid method was shorter than that of FVM.

• Journal of the Korean Society of Safety
• /
• v.5 no.3
• /
• pp.51-55
• /
• 1990

This study describes the engineering approach adopted to investigate sprinkler head during the early stage of a fire when they are subjected to convective heating and low gas velocities. Comparions are made between the parameters derived using basic methods, ie. ramp test, for evaluating sprinkler parameters(time constant, response time index) is illustrated. Evidence is presented that the propotion of heat loss by conduction from a sprinkler element may very typically employed in the rate of rise test. This fact alone may justfy the precautionary need to perform a limited number of rate of rise tests to confirm a sprinklers capacity to function correctly in reasonably unfavourable yet realistic conditions. The work is aimed primarily at meeting the needs of sprinkler industry.