• Structural Engineering and Mechanics
• /
• 제13권5호
• /
• pp.557-568
• /
• 2002

For the evaluation of the capability of a tubular member of an offshore structure to absorb the collision energy, a simple method can be employed for the collision analysis without performing the detailed analysis. The most common simple method is the rigid-plastic method. However, in this method any characteristics for horizontal movement and rotation at the ends of the corresponding tubular member are not included. In a real structural system of an offshore structure, tubular members sustain a certain degree of elastic support from the adjacent structure. End fixity has influences in the behaviors of a tubular member. Three-dimensional FEM analysis can include the effect of end fixity fully, however in viewpoints of the inherent computational complexities of the 3-D approach, this is not the recommendable analysis at the initial design stage. In this paper, influence of end fixity on the behaviors of a tubular member is investigated, through a new approach and other approaches. A new analysis approach that includes the flexibility of the boundary points of the member is developed here. The flexibility at the ends of a tubular element is extracted using the rational reduction of the modeling characteristics. The property reduction is based on the static condensation of the related global stiffness matrix of a model to end nodal points of the tubular element. The load-displacement relation at the collision point of the tubular member with and without the end flexibility is obtained and compared. The new method lies between the rigid-plastic method and the 3-demensional analysis. It is self-evident that the rigid-plastic method gives high strengthening membrane effect of the member during global deformation, resulting in a steeper slope than the present method. On the while, full 3-D analysis gives less strengthening membrane effect on the member, resulting in a slow going load-displacement curve. Comparison of the load-displacement curves by the new approach with those by conventional methods gives the figures of the influence of end fixity on post-yielding behaviors of the relevant tubular member. One of the main contributions of this investigation is the development of an analytical rational procedure to figure out the post-yielding behaviors of a tubular member in offshore structures.

• 대한기계학회논문집
• /
• 제9권4호
• /
• pp.452-462
• /
• 1985

본 논문에서는 금형의 형상과 단면 감소율등이 이에 미치는 영향을 조사하였 다. 이론과의 비교를 위해서 풀림처리된 특수강 소재인 SCM4로 실험을 행하였다. 압출하중은 로드셀(loadcell)로 측정하였으며 수치계산에서 구해진 속도장과 실제속도 장의 차이를 살펴보기 위해서 시편단면에 포토에칭(photoetching)한 압출시킬 시편의 그리드변형을 강소성유한요소법으로 계산한 그리드패턴과 비교 검토하였다.

• 소성∙가공
• /
• 제31권6호
• /
• pp.384-393
• /
• 2022

The flow forming process consists of a split process, a divide process, and a forming process. The split process is a forming process in which rollers radially permeate a simple disc-shaped forging material and split it in both directions to form a top-bottom bidirectional cup. It is advantageous for post-processing to deepen the forming depth in the split process but this characteristic causes the failure near the edge of the mandrel during the actual process. The split process was analyzed using Rigid Plastic FEM, and the stress analysis of the mandrel was conducted to find the cause of the failure. It was found that the failure occurred due to fatigue accumulation damage caused by repeated residual stress.

• 한국정밀공학회지
• /
• 제16권6호
• /
• pp.114-122
• /
• 1999

By using the FEM, a method for the stress analysis of the presented dies has been proposed. In this method, FEM and Lame equation are used for the analysis of the die insert and the stress ring, respectively. The proposed method includes the calculation of the contact pressure between the die insert and the stress ring. To show the validity, the proposed method has been applied to the simple test problem. The results of the stress analysis have been compared with the results of ANSYS, a commercial FE-code. Cold extrusion has been simulated by using the rigid-plastic FEM and the results of the deformation analysis have been used as the input of the die structure analysis. The stress states of the prestressed extrusion die have been obtained. The stress analysis of the die insert with stress rings has also been performed during extrusion.

• 소성∙가공
• /
• 제11권1호
• /
• pp.84-89
• /
• 2002

This study is concerned with the analysis of the forming characteristics of radial-forward extrusion. Angle between radial and forward extrusion, gap height, and friction factor are considered as important design factors to affect forming characteristics in radial-forward extrusion. The rigid-plastic finite element method is adopted to analyze the effects of design factors on forming loads. The incremental rates of loads are nearly constant except the deformation zone from radial to forward extrusion. The smaller angle induces lesser force increment, therefore forming load increases as the angle increases. Maximum load also increases as gap-height decreases and friction factor increases.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.265-268
• /
• 2003

In the extrusion process, the working material is forced to flow through a die with the desired profile. In general, the width of an extruded section is limited to about an inch less than the diameter of the round billet. But through the lip die, material is spreaded to produce a wider extruded section than the diameter of round billet. In this study, the extrusion process of an aluminum plate using the lip die is investigated. The width of the extruded plate is 450mm that is formed from the round billet with a diameter of 250mm. The flow characteristic through the lip die is considered to produce the wide-extruded plate with a small billet using rigid plastic FE analysis. Based on the result of FE analysis, new designs of lip die are proposed.

• 대한기계학회논문집A
• /
• 제27권5호
• /
• pp.815-822
• /
• 2003

The ring rolling process involves not only three-dimensional non-steady material flow and continuous change of radius and thickness of the ring workpiece but also heat transfer among workpiece, rolls and environment. In this study, deformation and heat transfer analyses were conducted by using the three-dimensional thermo-rigid-plastic finite element method. Three cases of plain ring rolling process were, respectively, simulated for the predictions of roll forces and the highest temperature zone during the aluminum process that ductile fracture often occurs. In addition, to prevent fishtail phenomena of the ring workpiece, axial rolls were used for this study.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.143-148
• /
• 1999

Design optimization is performed to calculated the draw-bead force for satisfying the design re-quirements. For an analysis tool a rigid-plastic finite element method with modified membrane element is adopted. response surface methodology is utilized for constructing the approximation surface for the optimum searching of draw bead force in sheet metal forming process. the algorithm developed is ap-plied to a design of the draw bead forces in a deep drawing process. The results show that the design of process parameters is applicable in complex metal forming analysis. It is also noted that the present algo-rithm enhances the stable optimum solution with small times of optimization iteration.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.311-314
• /
• 2004

The housing of the fuel injector supports the rod, the niddle valve and the solenoid. Based on the procedure of process design, in this paper, the forming operation is designed by the rigid-plastic finite element method. The metal flow during the forming of the fuel injector housing is axisymmetric until the final forming process. The response surface method has been performed to reduce the under-fill and the maximum effective strain. From the results of RSM, the second order regression model of equation is calculated by the least square method and used to determine the optimal values of design variables by simultaneously considering the responses. It is noted that upper under-fill is affected by the design variables of the $2^{nd}$ forming process and lower under-fill is affected by the design variables of the 1st forming process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.115-119
• /
• 2004

In the extrusion process, the working material is forced to flow through a die with the desired profile. In general, the width of an extruded section is limited to about an inch less than the diameter of the round billet. But through the lip die, material is spreaded to produce a wider extruded section than the diameter of round billet. In this study, the extrusion process of an aluminum plate using the lip die is investigated. The width of the extruded plate is 450mm that is formed from the round billet with a diameter of 250mm. The flow characteristic through the lip die is considered to produce the wide-extruded plate with a small billet using rigid plastic FE analysis. Based on the result of FE analysis, an optimized design of the lip die is then proposed.