• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.634-639
• /
• 2001

The current study addresses experimental and computational work of impulse wave discharged from the exit of two kinds of right-angle pipe bends, which are attached to the open end of a simple shock tube. The weak normal shock wave with its magnitude of Mach number from 1.02 to 1.20 is employed to obtain the impulse wave propagating outside the exit of the pipe bends. A Schlieren optical system visualizes the impulse wave discharged from the exit of the pipe bends at an instant. The experimental data of the magnitude of the impulse wave and its propagating directivity are analyzed to characterize the impulse waves discharged from the exit of the pipe bends and compared with those discharged from a straight pipe. Computational results well predict the experimented dynamic behaviors of the impulse wave. The results obtained show that a right-angle miter bend considerably reduces the magnitude of the impulse wave and its directivity toward to the pipe axis, compared with the straight pipe and right-angle smooth bend. It is believed that the right-angle miter bend pipe can playa role of a passive control against the impulse wave.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1996년도 International Conference on Agricultural Machinery Engineering Proceedings
• /
• pp.212-218
• /
• 1996

The concrete pipe used to distribute irrigation water to the right place now available is commonly made up of cement , sand, earth, pebble, etc. These materials with right ratio and right amount of water were mixed and squeezed through the pipe-making machine called vertical squeezed pipe-making machine, and then a cement prefabricated pipe is produced . This kinds of pipe has been expanding by leaps and bounds. Being little cement contents and low cost, the length of pipe is 1.0m or so with weight of 50kg, which is easy to be made and to be transported. The demolish pressure of it is 0.2 MPa or so, which meets the needs of agriculture irrigation . The buried pipe irrigation system, has been popularized in Jining Municipal , Shandong Province. By the year of 1995 , the irrigation area under pipe conveyancesystem usign this type of pipe has reached 74000 hectares. By calculation, about 27.7million ㎥ water, 2.88 million kWh power , 0.167 million man power and 1528 hectares cu tivated land will be saved one year, adding value of agriculture output increased by 10 million kg. The total economic benefits amount to 0.92 million US$ a year. The paper presents the pipe making course and its application on a large scale area.

• 한국소음진동공학회논문집
• /
• 제11권9호
• /
• pp.406-413
• /
• 2001

The current study depicts and experimental work of the impulsive wave discharged from the exit of several kinds of right-angle bend pipes, which are attached to the open end of a simple shock tube. The weak normal shock wave with Mach number from 1.02 to 1.20 is employed to obtain the impulsive wave propagating outside the exit of the pipe bends. The experimental data of the magnitude of the impulsive wave and its propagation directivity are analyzed to characterize the impulsive waves discharged from the right-angle bend pipes and compared with those from a straight pipe. The impulsive waves are visualized by a Schlieren optical system. A computation work using the two-dimensional, unsteady, compressible Euler equation is also carried out to represent the experimented impulsive waves. The results obtained show that a right-angle miter bend considerably reduces the magnitude of the impulsive wave and its directivity toward to the pipe axis, compared with the straight pipe. It is believed that the right angle miter bend pipe can play a role of passive control agianst the impulsive wave.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.317-322
• /
• 2001

This study depicts an experimental work of the impulsive wave discharged from the open end of several kinds of right-angle bend pipes, which are attached to the open end of a simple shock tube. The weak normal shock wave with its magnitude of Mach number from 1.03 to 1.20 is employed to obtain the impulsive wave propagating outside the open end of the bend pipes. The experimental data of the magnitude of the impulsive wave and its propagation directivity are analyzed to characterize the impulsive waves discharged from the right-angle bend pipes and compared with those from a straight pipe. The results obtained show that a right-angle miter bend considerably reduces the magnitude of the impulsive wave and its directivity toward to the pipe axis, compared with the straight pipe. It is believed that the right angle miter bend pipe can playa role of passive control against the impulsive wave.

• 토지주택연구
• /
• 제7권4호
• /
• pp.271-279
• /
• 2016

Recently developed trenchless construction methods ensure stability for the ground settlement by inserting steel pipes along the underpass section and integrating steel pipes before ground excavation to form pipe-roof. This study is to confirm the reinforcing effect of pipe-roof by measuring lateral earth pressure acting on the underpass constructed by the STS (Steel Tube Slab) construction method. For this purpose, lateral earth pressure was measured at the left and right side of the pipe-roof after installing earth pressure cells. As a result, lateral earth pressure was measured with considerable reduction because the integrated pipe-roof shared surcharge. Therefore, economic design for the underpass could be expected by sharing design load by pipe-roof. In addition, construction cost was analyzed according to the design-load sharing ratio by pipe-roof. As pipe-roof shares design load by 40%, the total construction cost can decrease by almost 10% in the case of four-lane underpass.

• 대한기계학회논문집B
• /
• 제21권1호
• /
• pp.68-78
• /
• 1997

A numerical study on the transient vapor flow and heat transfer is performed to investigate the ideal switching operation of heat source in a high temperature heat pipe. The cylindrical 2-dimensional compressible laminar vapor flow is assumed for the vapor space and the conjugate heat transfer for the heat pipe wall, wick and vapor space is calculated. The different boundary conditions such as constant heat flux, convective or radiative boundary at the outer wall are used respectively to compare the influence of boundary conditions on the transient operation. The transient temperature profile and the internal flow of the entire pipe for the switching operation are described as a result. The results show that the transient time is not significantly affected by the boundary conditions at the outer wall in present study. During the transition, two independent flows are observed temporarily on the right side and left side of the heat pipe. It is also found that the trend of temperature variation in the vapor region is different from the variation in the wick and wall region.

• 한국농공학회지
• /
• 제43권6호
• /
• pp.113-119
• /
• 2001

Experiments on the yield strength of pipe connectors made of metal wire, joint pins, pole pipes, multi span insertion joints, and T-clamp joints used in pipe houses were conducted. The strength of connections of a pipe connector made of metal wire was adequate but it had a big difference according to loading direction. Therefore as it is installed, its direction should be taken into consideration. The collapse load of pipes connected with a joint pin was lower than that of single pipes. In the part of frame member at which the great bending moment occurs, the use of joint pin should be avoided. Also experimental results showed that pole pipes for use in a part of frame buried under the ground were safe, and the strength of multi span insertion joints should be increased. The resistant moment of T-clamp was about 13.7% of a single pipe. In case that the external forces acting on left and right rafter are different. a unsymmetrical rotational force is produced at the multi span joint. If it is expected that the actual bending moment on the multi span joint is larger than resistant moment of T-clamp, a reinforcement to safely resist the rotational force is required.

• 복합신소재구조학회 논문집
• /
• 제2권3호
• /
• pp.18-24
• /
• 2011

이 연구에서 GRP 관의 하중-처짐 거동을 조사, 보고하였다. 지중매성 GRP관은 높은 내화학성, 높은 부식저항성, 경량성, 관표면의 매끄러움, 지반-관의 상호작용 고려에 따른 경제성 등의 탁원한 역학적, 물리적 특성들로 인해 건설현장에서 광범위하게 사용되고 있다. 지중에 매설되는 연성관을 설계하기 위해서는 ASTM D 2412 (2010)에 따라야 한다. ASTM D 2412 (2010)에 따라 설계할 경우, 관의 원강성 (PS)을 편평시험에 따라 먼저 결정해야 하는데, 이 시험이 귀찮고 노동력을 필요로 한다. 이러한 문제를 해결하기 위해 UTM에 설치된 형태의 GRP관의 하중-처짐 거동을 유한요소법에 따라 모사하였으며, 유한요소법에 의한 모사에는 재료의 탄성계수와 단면의 기하학적 치수 등 기초적인 자료를 사용하였다. 이와 같은 연구로부터, 관재료가 관의 단면내에서 비교적 일정하지 않음에도 불구하고 수직방향의 관변형이 3%와 5%가 발생할 경우, 편평시험과 수치해석적 연구 결과가 15%이내의 차이로 하중의 예측이 가능함을 알 수 있었다.

• 산업기술연구
• /
• 제24권A호
• /
• pp.239-250
• /
• 2004

Numerical analysis were performed to investigate the stability and internal movement of tunnel located beneath the base of abutment of bridge according to the method of supporting tunnel. Two supporting methods of the multi-staged grouting method with steel pipes and the large diameter of pipe supporting method were used in the centrifuge model tests. The slip form of model lining, specially built to simulate the process of tunnel excavating under the condition of accelerated g-level, was used in the centrifuge model tests. Four centrifuge model tests were performed, changing the supporting methods of the multi-staged grouting method with steel pipes and the large diameter of pipe supporting method and the location of model abutment base of bridge. For internal displacement of tunnel, movements of the crown. The left and the right sides of spring line were measured during the proceeds of excavating tunnel in centrifuge model tests. Test results were compared with numerically estimated values of internal displacement of tunnel by using the commercially available FEM software of PENTAGON-3D. It was found that they were in good agreements and the large diameter of pipe supporting method was more stable than the multi-staged grouting method with steel pipes with respect to the internal movement of tunnel.

• 한국지반신소재학회논문집
• /
• 제23권2호
• /
• pp.63-75
• /
• 2024

마시는 물은 인간의 기본적인 생활권 보장을 위한 필수적 요소로 깨끗한 물에 대한 품질은 항상 확보되어야 한다. 하지만 국내 수도시설을 집중 설치하였던 2000년 초반을 기점으로 현재 노후 상수도 시설이 증가하고 있으며, 색도 및 탁도와 같은 물의 변색, 이물질 누출 등의 사고가 빈번히 발생하고 있다. 실제로 모든 관의 교체는 불가능하기 때문에 2021년 제정된 상수관망시설 유지관리업무 세부기준에서는 상수관 세척을 의무화 하였으며, 다양한 세척 공법들을 통해 유지관리가 이루어지고 있는 실정이다. 상수관 세척 공법 중 스왑피그 공법은 관 내 이물질을 물리적으로 제거하는 방법으로 세척 효율이 가장 높은 것으로 평가 받고 있다. 하지만, 세척과정에서 스왑피그의 파손 및 변형에 따라 세척 효율은 변화하며, 분실의 가능성이 존재한다. 따라서 본 연구에서는 피그 자체의 재료를 변경하여, 압축력 및 관 내벽과의 밀착력을 향상시키고자 하며, 세척 효율 극대화를 위해 회전 블레이드를 삽입된 회전식 스왑피그를 개발하였다. 또한, 분실 가능성을 제거하고, 피그의 위치 파악을 위해 고강도 와이어 및 권취 장치를 추가적으로 개발하여, 투입구부터 토출구까지를 연결하였다. 각 세부 기술의 성능 검증 이후에는 30m 구간의 테스트베드에서 본 기술을 적용하였으며, 현장 적용성 평가와 더불어 공정 시간을 측정하여 기술의 성능을 검증하였다.