• Journal of Power Electronics
• /
• v.15 no.1
• /
• pp.116-122
• /
• 2015

This paper presents a new current sharing control strategy for parallel-connected, synchronised three-phase DC-AC converters employing space vector pulse width modulation (SVPWM) without current sharing reactors. Unlike conventional control methods, the proposed method breaks the paths of the circulating current by dividing the switching cycle evenly between parallel connected equally rated converters. Accordingly, any inter-module reactors or circulating current control will be redundant, leading to reductions in system costs, size, and control algorithm complexity. Each converter in the new scheme employs a synchronous dq current regulator that uses only local information to attain a desired converter current. A stability analysis of the current controller is included together with a simulation of the converter and load current waveforms. Experimental results from a 2.5kVA test rig are included to verify the proposed control method.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.409-411
• /
• 2007

This paper deals with an automatic tuning method of the notch filter to suppress oscillations in a permanent magnet linear synchronous motor(PMLSM) drive. First, it saves automatically the reference torque-component current when oscillations are detected. Then the oscillation frequency of the saved data is calculated by using the fast Fourier transform(FFT) algorithm. And also the Hanning function is used to reduce the leakage components due to the aperiodic measurement data. Finally, the proposed method tunes the notch filter to suppress oscillations. Experimental results on the test rig show the validity of the proposed method.

• International Journal of Automotive Technology
• /
• v.6 no.5
• /
• pp.537-544
• /
• 2005

This paper presents the efficiency measurement and energy analysis for a parallel HEY. Using the HEV test rig, the efficiency of each powertrain component is measured for a given driving cycle including the regenerative braking system. Accompanied by the efficiency measurements, a detailed energy analysis is performed. Based on the efficiency measurement and energy analysis, a HEV performance simulator is developed. Using the simulator, the HEV performance is evaluated for a mild hybrid system. It is expected that the HEV simulator developed can be used to obtain further optimization potentials.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.288-290
• /
• 1995

The new power train system for electric vehicle is introduced in this paper. This system includes two light weighted and high-efficient motor, two space vector PWM inverter, one system controller using CAN controller and DSP320C50. These are developed by KERI cooperated with 5 major industry companies, 5 universities including 2 foreign universities. The reliability and performance are proven by the test rig. The reference data will be collected for further researches.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.105-113
• /
• 2001

The effect of silver particle introduction on the rolling friction of AISI 52100 steel pairs has been investigated. Experiments were performed in dry conditions using a thrust bearing-type rolling test rig at a load range of 12 - 960 N and a sliding velocity range of 8 - 785 mm/sec with pure(99.99%) silver particles. Results showed that the introduced silver particles formed transfer layer, which protected virgin bearing surfaces and resulted in low rolling friction. By changing the quantity of silver particles, transitions in the rolling friction wear found. Results also showed that the variations in normal load and rolling speed also affected the rolling friction behavior. Analyses using SEM and EPMA showed that tile formation of transfer layer was mainly governed by the silver particle quantity, normal load and rolling speed, and this resulted in the different behavior of rolling friction. In this study, it was found that the low and stable rolling friction was resulted from the shakedown phenomena occurred at the silver transfer layer.

• Tribology and Lubricants
• /
• v.13 no.3
• /
• pp.85-92
• /
• 1997

An experimental study was performed to discover the tribological behaviors of pure silver coated 52100 bearing steel. Pure silver coatings ranging from 80 nm to several micrometers were produced by a thermal evaporation coating method. Experiments using a thrust ball bearing-typed rolling test-rig were performed for the investigations of the influence of coating thickness on the tribological rolling behavior. The existence of optimum film thickness which revealed minimum rolling resistance was discovered. A careful analysis on the contact surfaces for the optimum film thickness has been performed. The contact patches produced by the transferred silver films played an important role for the rolling resistance to keep low.

• Tribology and Lubricants
• /
• v.16 no.3
• /
• pp.188-193
• /
• 2000

An experimental study was performed to discover the effect of environment on the tribological behavior of Si-incorporated diamond-like carbon(Si-DLC) film slid on a steel ball. The films were deposited on Si(100) wafers by a radio-frequency glow discharge of mixtures of benzene and dilute silane gases. Experiments using a ball-on-disk test-rig was performed in vacuum, dry air and ambient air conditions. It was observed that coefficient of friction decreased as the environment changed from vacuum, to dry air. Chemical analyses of debris suggested that low and stable friction is closely related to the formation of silicon-rich oxide debris and the rolling action.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.2
• /
• pp.74-83
• /
• 1997

The non-periodic angular accelerations of engine are the major cause of gear rattle. This gear rattle is based on the existence of a backlash between the drive gear of input shaft and the free gear of output shaft in the gearbox. Especially, the neutral gear rattle have a very bad effect on the ride quality. Test-rig was constructed in order to evaluate the parameter influence upon the neutral gear rattle. Also, each different 4 type torsional characteristic of clutch was manufactured. Experimental conditions are the use of each different 4 type torsional characteristic of clutch and oil temperature variation in gearbox. In case of the same stiffiness of pre-damper type clutch at idling, the clutch of large hysteresis showed dam- ping effects at the 2nd input gear and the 2nd output gear. Also, the main-damper type clutch was shown to large resonance phenomenon at the 2nd input gear. Accordingly, main-damper type clutch was unapp- roriate at idling.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.10
• /
• pp.2194-2200
• /
• 2002

Transmission error is highly related to gear noise. In order to predict the helical gear noise, transmission error analysis is needed. Up to now, the studies for the transmission error were conducted by the modeling of helical gears only. However, since helical gears are supported by the shaft and bearing, transmission error has the effects of the elements. In this study, the procedure to consider the shaft deformation with bearing stiffness for the transmission error analysis is proposed. To do so, the relationship between gear error and shaft deformation is analytically derived. Shaft deformation with bearing stiffness is analyzed by FEM. It is measured in the experimental test rig by the non-contact displacement sensors. Using the tooth error from tooth modification and the shaft deformation, the effects of shaft on the loaded transmission error are investigated.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.81-84
• /
• 2006

To investigate the characteristics of water droplet on the gas diffusion layer from both upper-view and side-view of flow channel, a rig test apparatus was designed and fabricated with L-shape acryl plate in a $1mm{\times}1mm$ micro-channel. This experimental device is used to simulate the single droplet growth and its transport process under fuel cell operating condition. As a first step, we investigated the growth and transport of single water droplet with working temperature and air flow velocity. The contact angle and its hysteresis of water droplet at departing moment are measured and analyzed. It is expected that this study can provide the basic understanding of liquid water droplet behavior in gas flow channel and GDL interface during the PEM fuel cell operation.