• Journal of Biosystems Engineering
• /
• 제13권4호
• /
• pp.30-37
• /
• 1988

A mathematical model was developed and programmed for computer simulation of a prototype hot water boiler system with rice hull furnace to predict the temperature distributions in the rice hull furnace and water tank, mass flow rate of hot water and thermal efficiency of the system under various operation and design conditions. The effects of feed rate of rice hull, thickness of the furnace wall, the type of heat exchanger, diameter of the water circulation pipe, etc, on the performance of the system can be evaluated with this model. The validity and simulation results of this model will be published in the next paper.

• Asian-Australasian Journal of Animal Sciences
• /
• 제5권4호
• /
• pp.617-622
• /
• 1992

Four rumen-fistulated swamp buffaloes steers were used in a change-over experiment. This experiment was designed to provide a comparison of the effect of urea-ammonia treatment of rice straw with untreated rice straw. Nitrogen, mineral and trace elements were supplied at adequate levels to both diets in order to overcome deficiencies which may have otherwise confounded a direct comparison. There was a 46% increase in the intake of digestible organic matter (OM) with the urea-ammonia treated diet. This was contributed by a 17% increase in the digestibility of OM and a 25% increase in the voluntary intake of OM. Of the cell wall fraction, the digestibility of hemicellulose increased by the greatest amount (26%). There was an increased rate of passage of particulate matter out of the rumen for the treated straw, along with the increased rate of OM fermentation resulted in a 9% decrease in the amount of digesta dry matter (DM) contained in the rumen. The volatile fatty acid (VFA) pool in the rumen was 24% higher for the treated diet.

• Journal of Biosystems Engineering
• /
• 제1권1호
• /
• pp.15-15
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic?iency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet?ween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr?ease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$$$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea?ses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin?ear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num?ber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco?very rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of Biosystems Engineering
• /
• 제1권1호
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• 한국작물학회지
• /
• 제44권2호
• /
• pp.163-165
• /
• 1999

The study was conducted to find the critical concentrations of zinc toxicity and to determine the changes of the contents of free proline and organic acids with treatment of different zinc chloride concentrations during rice germination and seedlings grown for seven days. The concentration of zinc chloride, 140 ppm, inhibited root elongation as much as 46 times compared with the control, and the germination rate was also decreased in all treatments of zinc chloride, showing that the germination rate decreased more with increasing concentrations of zinc chloride. Its rate was only 13% with treatment of 140 ppm zinc chloride. The content of free proline with treatment of zinc chloride, 140 ppm, was highest about 4,873 $\mu$M at 3 days compared with the control. Malic acid concentration with treatment of zinc chloride, 140 ppm, increased to approximately 4 times compared to the control. Citric and succinic acid content were also slightly increased in all treatments of zinc chloride.

• 한국식품과학회지
• /
• 제29권4호
• /
• pp.737-744
• /
• 1997

4차원 반응표면분석에 의하여 느타리버섯과 현미를 이용한 즉석죽 제조조건의 최적화와 제조조건에 따른 제품의 관능적 품질을 모니터링 하였다. 즉석죽을 제조하기 위하여 현미의 수화시간은 50시간이 적당하였고, 찹쌀은 사용하기 전 1시간 수화하는 것이 바람직하였다. 관능적 특성별 최적조건은 점성이 수침미에 대한 현미의 비율 47.58%, 주입액 함량 569.68 mL, 호화 및 살균을 위한 가열 시간 52.40분이었고, 맛에 대한 최적조건이 47.15%, 568.49 mL, 53.04분, 조직감에 대한 최적조건이 44.06%, 558.54 mL, 53.84분, 전반적 기호도에 대한 최적조건이 46.20%, 561.64 mL, 51.60분 등으로 각각 나타났다. 즉석죽의 관능적 특성을 모두 만족시켜 주는 최적조건은 수침미에 대한 현미의 비율이 44%, 주입액 함량이 620 mL, 호화 및 살균을 위한 가열 시간이 56분으로 각각 나타났다. 즉석죽의 관능적 품질을 극대화하기 위한 제조조건의 예측값은 실제값과 유사하였다.

• Current Research on Agriculture and Life Sciences
• /
• 제32권2호
• /
• pp.91-97
• /
• 2014

우리나라 농가용 도정기의 구조요인과 도정성능을 분석하기 위하여, 판매되고 있는 농가용 도정기 29개 모델을 이용하여 제현장치와 정미장치로 분류하였고, 각 장치별로 구조적 특징을 조사하였고 그 결과를 바탕으로 성능요인을 분석하였다. 제현장치는 임펠러 회전속도가 주요 구조적 요인으로 조사되었으며, 4,800 rpm의 임펠러 회전속도가 65.5%로 가장 많이 사용하고 있는 것으로 나타났다. 이 회전속도에서 탈부율이 99.45%로 가장 높게 나타났고, 현미동할립율이 가장 낮게 나타나 제현성능에 가장 좋은 임펠러의 회전속도는 4,800 rpm인 것으로 분석되었다(p<0.05). 정미장치는 로터 선속도가 주요 구조적 요인으로 조사되었으며, 2 m/s의 로터 선속도가 60.1%로 가장 많이 사용하고 있는 것으로 나타났다. 이선속도에서 도정수율이 75.07%로 가장 높게 나타났고, 유실곡비율과 싸라기율이 각각 0.02%, 7.06%로 가장 낮게 나타나 정미성능에 가장 좋은 로터의 선속도는 2 m/s인 것으로 분석되었다(p<0.05).

• 한국식품영양학회:학술대회논문집
• /
• 한국식품영양학회 2001년도 동계 학술심포지움
• /
• pp.39-74
• /
• 2001

The endeavors enhancing the grain quality of high-yielding japonica rice were steadily continued during 1980s∼1990s along with the self-sufficiency of rice production and the increasing demands of high-quality rices. During this time, considerably great, progress and success was obtained in development of high-quality japonica cultivars and qualify evaluation techniques including the elucidation of interrelationship between the physicochemical properties of rice grain and the physical or palatability components of cooked rice. In 1990s, some high-quality japonica rice caltivars and special rices adaptable for food processing such as large kernel, chalky endosperm aromatic and colored rices were developed and its objective preference and utility was also examined by a palatability meter, rapid-visco analyzer and texture analyzer. The water uptake rate and the maximum water absorption ratio showed significantly negative correlations with the K/Mg ratio and alkali digestion value(ADV) of milled rice. The rice materials showing the higher amount of hot water absorption exhibited the larger volume expansion of cooked rice. The harder rices with lower moisture content revealed the higher rate of water uptake at twenty minutes after soaking and the higher ratio of maximum water uptake under the room temperature condition. These water uptake characteristics were not associated with the protein and amylose contents of milled rice and the palatability of cooked rice. The water/rice ratio (in w/w basis) for optimum cooking was averaged to 1.52 in dry milled rices (12% wet basis) with varietal range from 1.45 to 1.61 and the expansion ratio of milled rice after proper boiling was average to 2.63(in v/v basis). The major physicochemical components of rice grain associated with the palatability of cooked rice were examined using japonica rice materials showing narrow varietal variation in grain size and shape, alkali digestibility, gel consistency, amylose and protein contents, but considerable difference in appearance and torture of cooked rice. The glossiness or gross palatability score of cooked rice were closely associated with the peak. hot paste and consistency viscosities of viscogram with year difference. The high-quality rice variety “Ilpumbyeo” showed less portion of amylose on the outer layer of milled rice grain and less and slower change in iodine blue value of extracted paste during twenty minutes of boiling. This highly palatable rice also exhibited very fine net structure in outer layer and fine-spongy and well-swollen shape of gelatinized starch granules in inner layer and core of cooked rice kernel compared with the poor palatable rice through image of scanning electronic mcroscope. Gross sensory score of cooked rice could be estimated by multiple linear regression formula, deduced from relationship between rice quality components mentioned above and eating quality of cooked rice, with high Probability of determination. The ${\alpha}$ -amylose-iodine method was adopted for checking the varietal difference in retrogradation of cooked rice. The rice cultivars revealing the relatively slow retrogradation in aged cooked rice were Ilpumbyeo, Chucheongbyeo, Sasanishiki, Jinbubyeo and Koshihikari. A Tongil-type rice, Taebaegbyeo, and a japonica cultivar, Seomjinbyeo, shelved the relatively fast deterioration of cooked rice. Generally, the better rice cultivars in eating quality of cooked rice showed less retrogiadation and much sponginess in cooled cooked rice. Also, the rice varieties exhibiting less retrogradation in cooled cooked rice revealed higher hot viscosity and lower cool viscosity of rice flour in amylogram. The sponginess of cooled cooked rice was closely associated with magnesium content and volume expansion of cooked rice. The hardness-changed ratio of cooked rice by cooling was negatively correlated with solids amount extracted during boiling and volume expansion of cooked rice. The major physicochemical properties of rice grain closely related to the palatability of cooked rice may be directly or indirectly associated with the retrogradation characteristics of cooked rice. The softer gel consistency and lower amylose content in milled rice revealed the higher ratio of popped rice and larger bulk density of popping. The stronger hardness of rice grain showed relatively higher ratio of popping and the more chalky or less translucent rice exhibited the lower ratio of intact popped brown rice. The potassium and magnesium contents of milled rice were negatively associated with gross score of noodle making mixed with wheat flour in half and the better rice for noodle making revealed relatively less amount of solid extraction during boiling. The more volume expansion of batters for making brown rice bread resulted the better loaf formation and more springiness in rice bread. The higher protein rices produced relatively the more moist white rice bread. The springiness of rice bread was also significantly correlated with high amylose content and hard gel consistency. The completely chalky and large gram rices showed better suitability for fermentation and brewing. Our breeding efforts on rice quality improvement for the future should focus on enhancement of palatability of cooked rice and marketing qualify as well as the diversification in morphological and physicochemical characteristics of rice grain for various value-added rice food processings.

• 한국작물학회지
• /
• 제50권1호
• /
• pp.55-59
• /
• 2005

Rice farmers can save labor and expenses by using expanded rice husk (ERH) as a seedling medium since ERH is lighter and cheaper than other commercial seedling media (CSM). This study was carried out to develop a method for rice seedling cultivation using ERH as a seedling medium. It is suggested that a mixture of $60\%$ of ERH and $40\%$ of a CSM could be used as a seedling medium; the planting densities would be 240g per tray for infant seedlings and 200 g for young seedlings; and nitrogen (N) would be applied at a rate of 1g per tray for infant seedlings prior to planting and 2g per tray for young seedlings with division. Great care should be taken to use $CO(NH_2)_2$ as an N-source fertilizer. These results would lay a foundation for the rice seedling cultivation with ERH as a medium.

• 한국약용작물학회지
• /
• 제19권4호
• /
• pp.233-237
• /
• 2011

This study was carried out to investigate the seedling establishment and yield of direct-sown Platycodon grandiflorus seeds cultured by three ridge width, 0.4, 0.8, and 1.2 m and four mulching materials, rice straw, rice bran, black plastic film, and no mulching in upland. Seedling establishment rate (70%) was the highest in rice straw mulched plot of 500 seeds/$m^2$ sowed and root yield after one year was also the highest in rice straw mulched treatment and followed by rice bran, no mulching, and black plastic film treatment. In this result, ridge width 120cm and rice straw mulching combined treatment was best for getting the highest seedling establishment ratio and seedling numbers per area. However, ridge width and mulching materials should be considered soil moisture content and weed population for saving labor cost.