• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.125-129
• /
• 2004

[ $BaTi_4O_9$ ] thin film were grown on $Pt/Ti/SiO_2/Si$ substrate using rf magnetron sputter, and the microstructure and dielectric properties of the thin films were investigated. For the film grown at $350^{\circ}C$ and rapidly thermal annealed at $900^{\circ}C$, the $BaTi_5O_{11}$ Phase was formed. However, the $BaTi_4O_9$ phase was formed when the growing temperature exceeded $450^{\circ}C$ The dielectric constant of the $BaTi_4O_9$ thin film grown at $550^{\circ}C$ and rapidly thermal annealed at $900^{\circ}C$ was about 40 at low frequency range($100kHz{\sim}1MHz$) and 36 at microwave range($1{\sim}10GHz$) which is very close to that of the bulk $BaTi_4O_9$ phase. The dissipation factor was very low, about 0.005 at low frequency as well as microwave range.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.6
• /
• pp.501-506
• /
• 2006

Carbon nanotubes (CNTs) were grown with a microwave plasma enhanced chemical vapor deposition (MPECVD) method, which has been regarded as one of the most promising candidates for the synthesis of CNTs due to the vertical alignment, the low temperature and the large area growth. MPECVD used methane ($CH_4$) and hydrogen ($H_2$) gas for the growth of CNTs. 10 nm thick Ni catalytic layer were deposited on the Ti coated Si substrate by RF magnetron sputtering method. In this work, the pretreatment was that the Ni catalytic layer in different microwave power (600, 700, and 800 W). After that, CNTs deposited on different pressures (8, 12, 16, and 24 Torr) and grown same microwave power (800 W). SEM (Scanning electron microscopy) images showed Ni catalytic layer diameter and density variations were dependent with their pretreatment conditions. Raman spectroscopy of CNTs shows that $I_D/I_G$ ratios and G-peak positions vary with pretreatment conditions.

• Journal of the Korean Ceramic Society
• /
• v.37 no.8
• /
• pp.731-738
• /
• 2000

KLN(K3Li2Nb5O15) has attracted a great deal of attention for their potential usefulness in piezoelectric, electro-optic, nonlinear optic, and pyroelectirc devices. Especially, the KLN single crystal has been studied in the field of optics and electronics. However it is hard to produce good quality single crystals due to the crack propagation during crystal growing. One of the solutions of this problem is prepartion of thin film. But the intensive study has not been conducted so far. In this study, after the KLN thin film were prepared by R.F. magnetron Sputtering method on SiO2/Si substrate, the post-annealing methods of RTA(rapid thermal annealin) and IPA(insitu post annealing) were employed. The deposition condition of KLN thin film was RF power(100 W), Working pressure(100 mtorr). The commonness of both RAT and IPA was that the higher were deposition and post annealing temperature, the higher was the intensity of XRD but the less surface roughness. The difference of post-annealing methods affected XRD phase and surface condition very much. And in IPA process, the influence of O2 had much effect on the formation of KLN phase.

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.642-647
• /
• 2012

$TiO_2$ thin films for a pulse power capacitor were deposited by RF magnetron sputtering. The effects of the deposition gas ratio and thickness on the crystallization and electrical properties of the $TiO_2$ films were investigated. The crystal structure of $TiO_2$ films deposited on Si substrates at room temperature changed to the anatase from the rutile phase with an increase in the oxygen partial pressure. Also, the crystallinity of the $TiO_2$ films was enhanced with an increase in the thickness of the films. However, $TiO_2$ films deposited on a PET substrate showed an amorphous structure, unlike those deposited on a Si substrate. An X-ray photoelectron spectroscopy(XPS) analysis revealed the formation of chemically stable $TiO_2$ films. The dielectric constant of the $TiO_2$ films as a function of the frequency was significantly changed with the thickness of the films. The films showed a dielectric constant of 100~110 at 1 kHz. However, the dissipation factors of the films were relatively high. Films with a thickness of about 1000nm showed a breakdown strength that exceeded 1000 kV/cm.

• Journal of the Korean Ceramic Society
• /
• v.50 no.4
• /
• pp.288-293
• /
• 2013

Zn-In-Sn-O films were prepared at room temperature by combinatorial RF-magnetron co-sputtering system. The cationic contents of the films were varied using a compositionally combinatorial technique. The effects of the oxygen partial pressure and film compositionon the structural and electrical properties were investigated. The Zn-In-Sn-O films deposited at Ar gas atmosphere showed an amorphous phaseirrespective of the film composition. However, the amorphous Zn-In-Sn-O films with a Zn content below 30.0 at% were converted into a bixbyite type-ITO polycrystalline phase with an increase in the oxygen partial pressure. The resistivity, carrier concentration, and Hall mobility were strongly affected by the oxygen partial pressure and chemical composition of the film. At sufficiently high carrier densities above $5{\times}10^{18}cm^{-3}$, the conduction behavior of amorphous Zn-In-Sn-O film changes from thermally activated to degenerate band conduction accompanied with high mobility.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.10
• /
• pp.1976-1981
• /
• 2009

Transparent conducting aluminum-doped zinc oxide (AZO) thin films were deposited on Coming glass substrate using an Gun-type rf magnetron sputtering deposition technology. The AZO thin films were fabricated with an AZO ceramic target (Zn: 98wt.%, $Al_2O_3$: 2wt.%). The AZO thin films were deposited with various growth conditions such as the substrate temperature, oxygen pressure. X -ray diffraction (XRD), UV/visible spectroscope, atomic force microscope (AFM), and Hall effect measurement system were done in order to investigate the properties of the AZO thin films Among the AZO thin films prepared in this study, the one formed at conditions of the substrate temperature $100^{\circ}C$, Ar 50 sccm, $O_2$ 5 sccm and working pressure 5 motor showed the best properties of an electrical resistivity of $1.763{\times}10^{-4}\;[{\Omega}{\cdot}cm]$, a carrier concentration of $1.801{\times}10^{21}\;[cm^{-3}]$, and a carrier mobility of $19.66\;[cm^2/V{\cdot}S]$, which indicates that it could be used as a transparent electrode for thin film transistor and flat panel display applications.

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.4
• /
• pp.30-39
• /
• 2000

The variation of electrical properties of (Ba, Sr)TiO$_3$[BST] thin films deposited of RuO$_2$electrode with (Ba+Sr)/Tr ration was investigated. BST thin films with various (Ba+Sr)/Tr ration were deposited on RuO$_2$/Si substrates using in-situ RF magnetron sputtering. It was found that the electrical properties of BST films depends on the composition in the film. The dielectric constant of the BST films is about 190 at the (Ba+Sr)/Tr ration of 1.0, 1,025 and does not change markedly. But , the dielectric constant degraded to 145 as the (Ba+Sr)/Tr ratio increase to 1.0. In particular, the leakage current mechanism of the films shows the strong dependence on the (Ba+Sr)/Tr ration in the films. At the ration (Ba+Sr)/Tr=1,025, the Al/BST/RuO$_2$ capacitor show the most asymmetric behavior in the leakage current density, vs, electric field plot. It is considered that the leakage current of the (Ba+Sr)/Tr=1,025 thin films is controlled by the battier-Iimited process, i,e, Schottky emission.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.394-397
• /
• 2001

In this paper, in-situ deposited Ru/RuO$_2$ bottom electrodes have been investigated as new bottom electrodes for PZT thin film capacitor application. As a comparison, structural and electrical properties of PZT thin films on Pt/Ti and RuO$_2$ bottom electrodes are also investigated. The use of Ru/RuO$_2$ hybrid electrodes showed better electrical properties in compression with RuO$_2$ bottom electrode. With increasing Ru electrode thickness, the PZT thin films showed preferred orientation along the (110) direction and leakage current of PZT thin films were improved. The PZT thin films on Ru (100nm)/RuO$_2$ electrodes exhibited excellent ferroelectric properties such as remant polarization and coercive field of 7.2 C/$\textrm{cm}^2$ and 46.35 kV/cm, respectively.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2000.11a
• /
• pp.22-22
• /
• 2000

DRAM의 고접적화에 따라 기존의 반도체 공정에서 사용중인 여러 가지 기술들이 대부분 그 한계를 보이고 었으며, 대표적인 것이 캐퍼시터 형성기술이다. 따라서 1G DRAM급 이상의 초고집적 회로를 실용화하기 위해서 유전율이 높은 BST ($BrSrTiO_3$) 박막을 이용하여 캐패시터를 제조하려는 기술도 반드시 해결되어야 현재 활발히 실용화 연구가 진행중에 있다. BST 박막을 제조하는 방법은 RF magnetron sputtering, Ion beam reactive co-evaporation, LSM (Liquid Source Misted) CVD, MOCVD 등의 법으로 제조되고 있다. 본 연구에서는 전기-수력 학적 분무(Electro-Hydrodynamic Spray)현상을 이용한 MOCVD에 BaO, SrO, $TiO_2$ 박막을 증착 하여 전기장세기, 기판온도, 시간 등에 따른 특성을 조사하였다. 전기수력학적 분무를 이용한 증착법은 원료를 함유하는 용액을 이용함으로써 이송관의 가열이 필요 없이 장치를 간단하게 할 수 있고, 용액의 유량과 전기장의 세기에 따라 초미세 입자제어도 가능하며, 박막의 조성을 출발 용액으로 부터 조절하는 등의 특징을 가지고 있다. 증착한 박막의 표면, 단면 형상 및 조성을 분석하였고 결정화 여부 및 우선 배향성을 조사하였다. 현재는 개별 박막의 표현 형상과 조성에 대한 연구 결과를 얻었으며, 계속해서 박 막의 여러 특성에 대하 연구할 계획이다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.117-118
• /
• 2011

초경합금 위에 RF Magnetron Sputter를 이용하여 Ti 중간층을 증착 후 MPECVD(Microwave Plasma Enhanced Chemical Vapor Deposition) 시스템을 이용하여 나노결정 다이아몬드 박막을 증착 하였다. 공정압력, 마이크로웨이브 전력, Ar/$CH_4$ 조성비, 기판온도를 일정하게 놓고 직류 bias의 인가 여부를 변수로 하고 증착시간을 0.5, 1, 2시간으로 변화시켜 박막을 제작하였다. 제작된 시편은 FE-SEM과 AFM을 이용하여 다이아몬드 박막의 표면과 다이아몬드 박막의 표면 거칠기 등을 측정하였고, Raman spectroscopy와 XRD를 이용하여 다이아몬드 결정성을 확인하였다. Automatic Scratch �岵謙�ter를 이용하여 복합박막의 층별 접합력을 측정하였다. 바이어스를 인가하지 않고 다이아몬드 박막을 증착할 경우 증착 시간이 증가할수록 다이아몬드 입자의 평균 크기가 증가하며 입자들이 차지하는 면적이 증가하는 것을 확인하였다. 그러나 1시간이 경과해도 아직 완전한 박막은 형성되지 못하고 2시간 이상 증착 시 완전한 박막을 이루는 것이 확인되었다. 이에 비해서 바이어스 전압을 인가할 경우 1시간 내에 완전한 박막을 이루었다. 표면 거칠기는 바이어스를 인가한 경우가 그렇지 않은 경우에 비해서 조금 높은 것으로 나타났다. 이러한 바이어스 효과는 표면에서의 핵생성 밀도 증가와 재핵생성 속도 증가에 기인하는 것으로 해석된다.