• 전기학회논문지
• /
• 제62권1호
• /
• pp.29-36
• /
• 2013

This paper deals with the analysis of the customer voltage characteristic in distribution system interconnected with large scale PV system. There would be many power quality issues which are caused by reverse power flow of PV system interconnected with distribution system. In order to analyze the effect of PV system on the customer voltage, detailed modeling method of distribution system and modified modelling method of PV system are proposed using PSCAD/EMTDC in this paper. So far, less than dozens KW of PV system can be simulated with the existing modelling method. Therefore, a new modeling method which can simulate the large scale PV system is proposed by considering the relationship equation on the phase and voltage in the current control algorithm. From the simulation result of proposed modelling method, it is confirmed that an optimal operation method in distribution system is suggested by analyzing the effect of PV system on customer voltage.

• Journal of Power Electronics
• /
• 제15권1호
• /
• pp.86-95
• /
• 2015

An active clamp high step-up boost converter with a coupled inductor is proposed in this paper. In the proposed strategy, a coupled inductor is adopted to achieve a high voltage gain. The clamp circuit is included to achieve the zero-voltage-switching (ZVS) condition for both the main and clamp switches. A rectifier composed of a capacitor and a diode is added to reduce the voltage stress of the output rectifier diode. As a result, diodes with a low reverse-recovery time and forward voltage-drop can be utilized. Since the voltage stresses of the main and clamp switches are far below the output voltage, low-voltage-rated MOSFETs can be adopted to reduce conduction losses. Moreover, the reverse-recovery losses of the diodes are reduced due to the inherent leakage inductance of the coupled inductor. Therefore, high efficiency can be expected. Firstly, the derivation of the proposed converter is given and the operation analysis is described. Then, a steady-state performance analysis of the proposed converter is analyzed in detail. Finally, a 250 W prototype is built to verify the analysis. The measured maximum efficiency of the prototype is 95%.

• 멤브레인
• /
• 제11권4호
• /
• pp.152-160
• /
• 2001

본 연구는 아크릴 폐수의 COD제거를 위한 전터리 공정 및 전 처리된 아르릴폐수를 한외여과 중공사형 모듈과 역삼투 나권형 모듈에 적용하여 적용압력과 온토변화에 따른 한외여과막과 역삼투막의 분리특성을 고찰하였다. 또한, 장시간 연속운전으로부터 한외여과 및 역삼투 막의 세척 적정시간을 결정하고, 운전시간에 따른 막오염을 고찰하였다. 14시간을 기준으로 한외여과 막의 플럭스가 급격히 떨어지고 있으며, 역삼투 막도 비슷한 경향을 나타내고 있다. CaO 및 모래여과장치를 거친 처리수를 중화처리 하여 UF/RO공정에 적용한 결과 COD 및 TDS가 배출허용 기준치 이하로 제거됨을 알 수 있었다.

• 전력전자학회논문지
• /
• 제26권5호
• /
• pp.376-379
• /
• 2021

The design and performance of a SiC-MOSFET-based 11-kW bi-directional on-board charger (OBC) for electric vehicles is presented. The OBC consists of a three-phase two-level AC/DC converter and a CLLLC resonant converter. All the power devices are implemented with SiC-MOSFETs to reduce the conduction losses generated in the OBC, and the DC-link voltage is designed to track the level of battery voltage in the forward and reverse powering modes. As a result, the CLLLC resonant converter always runs at the switching frequency near the resonant frequency, resulting in high-efficiency operation at the maximum powering modes. As the DC-link voltage varies according to the battery voltage, the AC/DC converter in the proposed OBC adopts an adaptive DC-link voltage controller. The performance of the proposed 11-kW OBC is verified by a prototype converter with the following specifications: three-phase 60-Hz 380-V input, 11-kW capacity, and battery voltage range of 214-413-V, resulting in the conversion efficiency of over 95.0-% in the forward and reverse powering modes.

• 시스템엔지니어링학술지
• /
• 제14권2호
• /
• pp.58-66
• /
• 2018

This paper represents a systematic approach aimed at improving the performance of the proportional integral (PI) controller for the Advanced Power Reactor (APR) 1400 Feedwater Control System (FWCS). When the performance of the PI controller offers superior control and enhanced robustness, the steam generator (SG) level is properly controlled. This leads to the safe operation and increased the availability of the nuclear power plant. In this paper, a systems engineering approach is used in order to design a novel PI controller for the FWCS. In the reverse engineering stage, the existing FWCS configuration, especially the characteristics of the feedwater controller as well as the feedwater flow path to each SG from the FWCS, were reviewed and analysed. The overall block diagram of the FWCS and the SG was also developed in the reverse engineering process. In the re-engineering stage, the actual design of the feedwater PI controller was carried out using a genetic algorithm (GA). Lastly, in the validation and verification phase, the existing PI controller and the PI controller designed using GA method were simulated in Simulink/Matlab. From the simulation results, the GA-PI controller was found to exhibit greater stability than the current controller of the FWCS.

• 한국안전학회지
• /
• 제28권2호
• /
• pp.26-30
• /
• 2013

The purpose of this study is to find risk factors by analyzing the operation principle of a photo coupler (P/C) used to remove the noise of electronic devices and establish a base for the performance improvement of developed products. It was found from the P/C circuit analysis of normal products that they were equipped with an electrolytic condenser of $0.1{\mu}F$ to smooth system signals. Due to the epoxy resin packing the external part of the P/C, this study experienced a limit to visually examine the damage to it. It could be seen from the analysis of electric characteristics of the P/C that the forward voltage ($V_f$) and reverse current ($I_r$) were 1.3 V and 10 uA, respectively. In addition, it is required that the breakdown voltage (VCE) between the collector (C) and emitter (E) be maintained at less than 35 V. The and of the damaged product #1 were comparatively good. However, the measurement of was 100.0 uA. From this, it is thought that a short circuit occurred to the internal circuit. Moreover, from the fact that the of the damaged product #2 was open circuit and the measurement of was 0.0 uA, it is thought that the collector and emitter was separated or insulation resistance was significantly high. Furthermore, from the fact that the of the damaged product #3 was open circuit and the measurement of was 0.0 uA, it is thought that the space between the collector (C) and emitter (E) failed to meet the design standard or that they were separated. Therefore, it is thought that fabricating the P/C by increasing the reverse current 10 mA to 50 mA will prevent its malfunction.

• 대한기계학회논문집A
• /
• 제28권12호
• /
• pp.1958-1967
• /
• 2004

This paper describes the method to rapidly fabricate the large-sized physical model with the envelope model size of more than 600 mm${\times}$ 600 mm${\times}$ 600 mm using two type semi-automatic VLM-ST processes in connection with the reverse engineering technology. The fabrication procedure of the large-sized solid shape is as follows: (1) Generation of STL data from 3D scan data using 3D scanner, (2) generation of shell-type STL data by Boolean operation, (3) division of shell-type STL data into several pieces by solid splitting, (4) generation of USL data for each piece with VLM-Slicer, (5) fabrication of each piece by cutting and stacking according to USL data using VLM-ST apparatus, (6) completion of a shell-type prototype by zigzag stacking and assembly for each piece, (7) completion of a 3D solid shape by foam backing, (8) surface finish of a completed 3D solid shape by coating and sanding. In order to examine the applicability of the proposed method, the miniature of the Mount Rushmore Memorial has been fabricated. The envelope model size of the miniature of the Mount Rushmore Memorial is 1,453 mm${\times}$ 760 mm${\times}$ 853 mm in size. From the result of the fabricated miniature of the Mount Rushmore Memorial, it has been shown that the method to fabricate the large object using two type semi-automatic VLM-ST processes in connection with the reverse engineering technology are very fast and efficient.

• 전력전자학회논문지
• /
• 제7권4호
• /
• pp.346-352
• /
• 2002

본 논문에서는 정류용 다이오드의 역 회복시 발생하는 손실을 줄이기 위한 새로운 듀얼 모드로 동작하는 ZCS-PWM 승압형 컨버터를 제안한다 제안된 회로에서 각각의 스위치는 소프트 스위칭 조건에서 매 사이클마다 교번으로 스위칭 동작을 하고 스위치 $S_2$에 직렬로 공진형 인덕터 Lr을 달아서 스위칭 손실과 EMI 노이즈와 관련된 정류용 다이오드$(D, D_1)$의 역 회복 전류를 감소시켰다. 제안된 컨버터는 기존의 ZVT-PWM 컨버터$^{[2]}$에 수동 및 능동 소자를 더 이상 추가하지 않기 때문에 각 소자들이 받는 전류/전압 스트레스는 기존의 하드 스위칭 컨버터 같다. 본 논문에서는 제안된 회로의 동작을 분석하고 이를 바탕으로 제작 및 실험을 통해서 타당성을 입증하였다.

• Membrane and Water Treatment
• /
• 제3권3호
• /
• pp.169-179
• /
• 2012

One of the major limitations in the use of commercial aromatic polyamide thin film composite (TFC) reverse osmosis (RO) membranes is to maintain high performance over a long period of operation, due to the sensitivity of polyamide (PA) skin layer to oxidizing agents, such as chlorine, even at very low concentrations in feed water. This article reports surface modification of a commercial TFC RO membrane (BW30-Dow Filmtec) by covering it with a thin film of poly(vinyl alcohol) (PVA) crosslinked with glutaraldehyde (GA) to improve its resistance to chlorine. Crosslinking reaction was carried out at 25 and $40^{\circ}C$ by using PVA 1.0 wt.% solutions at different GA/PVA mass ratio, namely 0.0022, 0.0043 and 0.013. Water swelling measurements indicated a maximum crosslinking density for PVA films prepared at $40^{\circ}C$ and GA/PVA 0.0043. ATR-FTIR and TGA analysis confirmed the reaction between GA and PVA. SEM images of the original and modified membranes were used to evaluate the surface coating. Chlorine resistance of original and modified membranes was evaluated by exposing it to an oxidant solution (NaClO 300 mg/L, NaCl 2,000 mg/L, pH 9.5) and measuring water permeability and salt rejection during more than 100 h period. The surface modification effectively was demonstrated by increasing the chlorine resistance of PA commercial membrane from 1,000 ppm.h to more than 15.000 ppm.h.

• 공업화학
• /
• 제10권4호
• /
• pp.563-567
• /
• 1999

용질배제율이 우수한 나권형 FT-30 폴리아미드 복합막을 상용하여 cephalosporin C를 농축하기 역삼투 농축실험을 하였다. $4{\sim}20kg/cm^2$의 압력과 100~1000 mg/L의 농도, 그리고 2.8과 5.6 L/min의 유속을 갖는 실험 조건하에서 cephalosporin C 수용액의 수투과율과 용질의 배제율 및 물질전달 계수를 구하였다. Cephalosporin C를 분리하는데 있어서 압력이 증가함에 따라 투과 플럭스가 증가하는 것으로 나타났다. 이 결과는 Kedem-Katchalsky 모델에서 예측한 것과 일치하였다. 그리고 배제율은 1에 가까웠다. 또한 공급액의 농도가 증가할수록 cephalosporin C의 배제율은 낮아지는 것으로 나타났다. 배제율은 고농도보다는 저온도에서 높게 나타났으나 그 감소 정도는 작았다.