• Journal of the Korean GEO-environmental Society
• /
• v.16 no.1
• /
• pp.45-53
• /
• 2015

This study has obtained Soil Water Retention Curve (SWRC) of the unsaturated soil from the volumetric pressure plate extractor test and the triaxial compression tests was also conducted. By using the rainfall data measured in the site the seepage analysis of unsteady flow was performed with the program of SEEP/W in Geostudio 2007 and stability of the slope was analyzed with SLOPE/W program. Results of analyses show that shear strength of the unsaturated soil increases with the increase of matric suction. And it was also found that the net volumetric stress and the apparent cohesion increased with the matric suction. The seepage analysis of rainfall represents that the increasing rate of negative pore pressure at the zone of large negative pore pressure is appeared to be high even though lower rainfall intensity, but this tendency declines with ground depth. The stability analysis of slope was carried out for the actual plane of failure with the data representing the field condition. The factor of safety thus calculated was about unity (1.0) or just below, which means that the adopted method of analysis is in good agreement with the field condition.

• The Journal of Korean Academy of Prosthodontics
• /
• v.53 no.1
• /
• pp.66-73
• /
• 2015

Alveolar bone loss and deformation can be a risk factor in removable prosthetic restoration treatment for partially or fully edentulous patients. The use of implants to solve this problem could improve the support, retention and stability of removable restoration. Attachments used in implant overdenture are versatile. The attachment should be selected according to the patients' conditions. Milled bar has been chosen when readymade bar could not be used because of the narrow distance between implants or firm stability and support of supra-structure were needed. Milled bar design is able to provide cross arch stabilization and comfortability to patients. However, it needs skilled laboratory procedures. Recently, the fabrication of milled bar has become simple and its suitability has been improved through the development of CAD/CAM system. In a 67-year-old female Alzheimer's disease patient with 8 implant fixtures on the fully edentulous site of mandible, implant overdenture with using milled bar and magnet attachment was planned. As rapid treatment was required, CAD/CAM system was used to make a simple laboratory procedure instead of a traditional fabrication process. With this system, implant overdenture with milled bar can be fabricated esthetically and functionally.

• Journal of the Korean Ceramic Society
• /
• v.22 no.1
• /
• pp.11-18
• /
• 1985

The effect of stress induced phase transformation on $Al_2 O_3$ matrix dispersed with $ZrO_2-Y_2O_3$ has been studied. In order to determinate the mechanical properties three $Al_2O_3-ZrO_2$ composite series containing 1, 3 and 5 mole% $Y_2O_3$ were prepared. The starting materials were $Al_2O_3$ and $ZrO_2-Y_2O_3$ which was prepared from the aqueous solution of high purity $YCl_3$.$6H_2O$ and $ZrOCl_2$.$8H_2O$. Powder mixtures of $Al_2O_3-ZrO_2$ containing $Y_2O_3$ have been prepared by ball-milling with methanol and the samples were formed by isostatic press and sintered at 150$0^{\circ}C$ for 2hrs. After sintering. the specimens were polished for mechanical determination. The relative density of sintered specimens were also measured. It was found that the addition of 1, 3mole% to {{{{ { ZrO}_{2 } }} allowed full retention of the tetragonal phase in $Al_2O_3-ZrO_2$ but partially stabilized zirconia (PSZ) was produced by additions of 5 mole% $Y_2O_3$.The critical stress-intensity factor KIc of $A_2O_3-ZrO_2$ (containing 1 mole% $Y_2O_3$) composite materials increased with increasing $ZrO_2$ content, The maximum value of KIC=7Mn/$m^3$/2 at 20 mole% $ZrO_2$ exhibited about twice that of the $Al_2 O_3$ The modulus of rupture exhibited a trend similiar to KIC The maximum value of MOR was 580MN/m2. As the amount of Y2O3 increase it was observed that the maximum of KIC and MOR decreased : Additions of 3 mole% $Al_2O_3$ $Y_2O_3$ allowed the maximum of KIC 6MN/$m^3$/2 MOR 540MN/$m^2$ at 15 mole% $ZrO_2$ additions of 5 mole% $Y_2O_3$ allowed the maximum of KIC 5MN/$m^3$/2 MOR 410MN/$m^2$ at 10 mole% $ZrO_2$.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.7
• /
• pp.839-845
• /
• 2007

Temperature dependence of kinetic constants in the anaerobic acidogenesis was investigated using anaerobic chemostat-type reactor. Glucose was used as a substrate in this experiment. Temperature ranging from 15 to $30^{\circ}C$ were studied. The saturation constant$(k_s\upsilon)$ and growth yield(Y) decreased with increasing temperature, while the maximum specific substrate utilization rate$(\upsilon_{max})$ increased. A temperature correction factor$(Q_{10})$ values of the substrate utilization rate and bacteria growth rate were the range from 1.3 to 2.2 and 1.5 to 2.2, respectively. The growth yield(Y) for the acidogenesis process was less sensitive to temperature changes than the maximum specific substrate utilization rate$(\upsilon_{max})$. The simulation model of the relationship between the substrate and sludge retention time(SRT) at the temperature range of 20 to $30^{\circ}C$ is obtained as the following ; $1/SRT={(6.53){\cdot}(1.038)^{T-20}{\cdot}(S/X)}/{(1.38){\cdot}(0.983)^{T-20}+(S/X)}$.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.5
• /
• pp.378-385
• /
• 2014

The chlorophyll-a concentration in algae bloom warning system of Hangang basin did not predict the cyanobacteria dominance. In this study, suggest the predicting indicator of cyanobacteria dominance through analyzing the environmental factors affecting on the cell count of cyanobacteria. Firstly, the dominance of algae was analyzed with seasonal variation during Jan. 2012~Sep. 2013. The diatom dominated phytoplankton communities during the period of January~April. In the May~June, the green algae dominated. And, the dominance of algae was changed to cyanobacteria in the July~August. Also, the environmental factors affecting to cyanobacteria blooms ; nutrients (TN, TP), temperature, precipitation, dam-discharge were evaluated during the study period. Rather than temperature factor, relatively low dam discharge causes cyanobacteria to grow rapidly and create a blooms. The low dam-discharge may increase the water retention time. Finally, it is proved that a low ratio of TN to TP (<29:1) can favour the development of cyanobacteria blooms. Thus, the predicting indicator (TN:TP) have need to apply to the alarm bloom warning system of Hangang basin.

• Analytical Science and Technology
• /
• v.27 no.4
• /
• pp.201-212
• /
• 2014

Polycyclic aromatic hydrocarbons (PAHs) that are carcinogenic and persistent will be restricted in consumer products from December 27, 2015 by EU REACH regulation. Pretreatment using Soxhlet extraction and quantitative analysis by GC-MS were studied to develop the method for analyzing 18 PAHs in consumer products as well as to detect the amounts and the kinds of PAHs in consumer products such as grips of a bag and a hammer, a cable and a plastic sandal. Linearity and precisions were evaluated by analyses of the standard PAH solutions ranging from 0.3125 mg/L to 5.00 mg of each of 18 PAHs. Linearity of resulting standard curves for all 18 PAHs were obtained with $R^2$ above 0.999. Precisions of the retention times and the peak areas were found to be 0.00%~0.05% and 1.16%~3.69% of relative standard deviations, respectively. The recoveries for spiked samples were all around 95%~105% after Soxhlet extration using three different solvents such as dichloromethane, hexane and toluene. The limits of quantitation for 18 PAHs in solutions and polymer samples by GC-MS were evaluated to be 0.327 mg/L (Benzo[ghi]perylene)~0.464 mg/L (Acenaphthylene) and 1.635 mg/kg (Benzo[ghi]perylene)~2.32 mg/kg (Acenaphthylene) based upon dilution factor of 5, respectively. Under the developed analytical method, only trace amounts of phenanthrene were detected in three samples while 15 kinds of PAHs including phenanthrene were detected in a grip of hammer with concentrations of maximum 83.4 mg/kg of Phenanthrene and minimum 8.5 mg/kg of Acenaphthylene. Further studies are needed to decrease the quantitation limit and to check the feasibility of decreasing Soxhlet time as well as to demonstrate cases that the clean up is required.

• The Journal of the Korea Contents Association
• /
• v.15 no.4
• /
• pp.519-529
• /
• 2015

The purpose of this study is to examine the determinant factors of maintaining employment in young adults with intellectual disabilities who took part in a vocational training program and was employed. The determinant factors were from four areas, such as physical competence, job-related task performance, emotional behaviors, and functional adaptive behaviors. 64 young adults with intellectual disabilities participated in this study. The participants' capacities were examined during the program, and then their job retention was examined through a follow-up survey six month after the end of the program. Tests contained hand dexterity, grasp strength, finger strength, visual-perception, Survey of Functional Adaptive Behaviors, and Observational-Emotional Inventory-Revised. After data collection, the data were analyzed by binary logistic regression. The results indicated that dexterity in both hands (OR= 1.123) in physical competence, anxiety (OR= .733) and socialization (OR= .429) in emotional behaviors, and academic skills (OR= 1.077) and vocational skills (OR= 1.542) in functional adaptive behaviors were significant determinant factors. These significant factors which affected job attention were consistent with the results from previous studies, and should be considered when designing and constructing an effective career and vocational education program for young adults with intellectual disabilities.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.11
• /
• pp.772-779
• /
• 2012

For improving performance of conical air diffuser generating fine bubble, both experimental and numerical simulation method were used. After adapting diffusers inner real scale bubble column, suitable for various diffuser submergence, the effect of diffuser submergence on oxygen transfer performance such as Oxygen Transfer Coefficient ($K_{L}a_{20}$) and Standard Oxygen Transfer Efficiency (SOTE) was investigated empirically. As flow patterns for various diffuser number and submergence were revealed throughout hydrodynamic simulation for 2-phase fluid flow of air-water, the cause of the change for oxygen transfer performance was cleared up. As results of experimental performance, $K_{L}a_{20}$ was increased slightly by 7% and SOTE was increased drastically by 39~72%, 5.6% per meter. As results of numerical analysis, air volume fraction, air and water velocity in bioreactor were increased with analogous flow tendency by increasing diffuser number. As diffuser submergence increased, air volume fraction, air and water velocity were decreased slightly. Because circulative co-flow is determinant factor for bubble diffusion and rising velocity, excessive circulation intensity can result to worsen oxygen transfer by shortening bubble retention time and amount.

• YAKHAK HOEJI
• /
• v.59 no.3
• /
• pp.98-106
• /
• 2015

Analytical method for related substances can be categorized into two methods depending on the necessity of reference standard (RS). The analytical method of related substances with RS is fast and accurate, but it's very expensive and technically difficult to synthesize RS due to their complicated structure. Another method is using relative retention time (RRT) and relative response factor (RRF) which are already validated with RS. Validation of this method is not easy and time consuming, but once it has been developed, it can save cost and time. In this study, we developed the analytical method for related substances of fenofibrate using RRT and RRF. We validated the method by evaluating specificity, linearity, accuracy and precision according to the "Manual for Guideline Application for Validation of Analytical Procedures" of MFDS. Also, we calculated RRT and RRF between fenofibrate and fenofibrate related substances. The results of this study showed high specificity for fenofibrate and fenofibrate related substances. Correlation coefficient(r) of all substances were more than 0.99, and the recovery of fenofibrate, fenofibrate related substance I, II and III were 99.44%, 100.84%, 99.14% and 101.58%, respectively. Precision of fenofibrate and its related substances were ranged between RSD 0.29% and 0.93%. Quantification limits of fenofibrate, fenofibrate related substance I, II and III were determined to be $0.03{\mu}g/ml$, $0.05{\mu}g/ml$, $0.04{\mu}g/ml$ and $0.02{\mu}g/ml$, respectively by confirming signal to noise ratio of each chromatogram. The RRT for fenofibrate related substance I, II and III were determined to be 0.35, 0.41 and 1.34, respectively. Also, the RRF for fenofibrate related substance I, II and III were determined to be 1.28, 0.98 and 0.79, respectively. The developed method was applied to determine contents for fenofibrate related substances in commercial fenofibrate (active pharmaceutical ingredient). As a result, developed analytical methods of related substances will be used for revising the monograph of fenofibrate in Korean Pharmacopoeia revision and contribute quality control of drugs by improving cost and time consuming problem of RS.

• Polymer(Korea)
• /
• v.31 no.6
• /
• pp.505-511
• /
• 2007

Poly(lactide-co-glycolide)(PLGA) and hyaluronic acid (HA) has been widely used as biocompatible scaffold materials to regenerate tissue. In this present study, we fabricated microporous PLGA and HA loaded PLGA scaffolds by a emusion freeze-drying method. In order to confirm that the release profile of cytokine or water-soluble drugs, we manufactured the granulocyte macrophage colony stimulating factor(GM-CSF) loaded PLGA and HA-PLGA scaffold. All scaffolds were characterized using scanning electron microscope(SEM), mercury porosimeter and wettability measurement. Cell proliferation and viability were assessed by a 3-(4,5-dimethylthiazole-2-yl)-2,5-diphenyltetrazolium-bromide (MTT) test. The porosity of HA-PLGA scaffold was greater than 95% with the total pore area of $261\;m^2/g$. The HA-FLGA scaffold exhibited well interconnected pores to allow greater cell adhesion and prolixferation. It was proven by higher cell viability in the HA-PLGA scaffold than PLGA alone. This may be due to the enhanced natural properties and higher water retention capacity of HA.