• Journal of the Korean Society for Heat Treatment
• /
• v.21 no.3
• /
• pp.137-143
• /
• 2008

Effect of quenching medium on the mechanical properties of ductil iron GCD 50 has been investigated using ADI treated specimens. The specimens have been austenitized at $900^{\circ}C$ for 2 hours, followed by controlled cooling to $800^{\circ}C$ under the cooling rate of $0.05^{\circ}C/sec$, then austempered at $380^{\circ}C$, $330^{\circ}C$, $280^{\circ}C$ and $230^{\circ}C$ for 1 hour. The specimens treated in the salt of 5% water were found to have higher tensile strength than that of the normal salt bath. Elongation and impact energy increased in proportion to the increase of retained austenite volume fraction. The increase of cooling rate of the salt by the addition of 5% water to the salt resulted in the increase of retained austenite volume fraction and the formation of fine bainitic ferrite.

• Korean Journal of Materials Research
• /
• v.19 no.6
• /
• pp.305-312
• /
• 2009

The effects of Quenching and Partitioning (Q&P) and Annealed Martensite (AM) heat treatment on the microstructure and tensile properties were investigated for 0.24C-0.5Si-1.5Mn-1Al steels. The Q&P steels were annealed at a single phase ($\gamma$) or a dual phase (${\gamma}+{\alpha}$), followed by quenching to a temperature between $M_s$ and $M_f$. Then, enriching carbon was conducted to stabilize the austenite through the partitioning, followed by water quenching. The AM steels were intercritically annealed at a dual phase (${\gamma}+{\alpha}$) temperature and austempered at $M_s$ and $M_s{\pm}50^{\circ}C$, followed by cooling in oil quenching. The dual phase Q&P steels showed lower tensile strength and yieldyield strength than those of the single phase Q&P steels, and tThe elongation for the dual phase Q&P steel was partitioning 100s higher than that of that for the single phase Q&P steels as the partitioning time was less than 100s up to partitioning 100s. For AM steels, the tensile/yield strength decreased and the total elongation increased as the austempering temperature increased. The stability of the retained austenite controlled the elongation for Q&P steels and the volume fraction of the retained austenite controlled the elongation for AM steels.

• 한국해양학회지
• /
• v.3 no.2
• /
• pp.47-54
• /
• 1968

Monthly mean values for EDTA hardness in the Han River water were determined for March 1966 through May 1967. The hardness was retained a range of 22-59 mg/L the maximum value of 59 mg/L was approached in the months of mid-winter, indicating a seasonal variation. The annual ranges of Ca and Mg were 3.7-9.1 mg/L, 1.5-10.4 mg/L, respectively. The annual range of Mg:Ca ratio was 0.18-2.60. And the hardness correlated closely with Mg volume. In Korea, fortunately, most river waters are not yet suffering from damaging pollution. We must try to establish our water quality criteria based on scientific data, and make research recommendations for the following water uses; public water supplies, aquatic life and wildlife, industry, recreation and aesthetics.

• The Journal of Engineering Geology
• /
• v.13 no.1
• /
• pp.51-65
• /
• 2003

A series of numerical simulations were carried out using STOMP( Subsurface Transport over Multiple Phase) simulator. The flow and distribution of LNAPL were analyzed in homogeneous fine and coarse sand. Vertical movement of LNAPL is faster in the coarser sand. But the total volume of LNAPL retained in the unsaturated zone is larger in the finer sand. A fine layer in the coarse sand domain is also simulated. The results showed that the retained LNAPL volume and shape are highly influenced by the Position of the fine layer. Flow and distributions of LNAPL were simulated when there were heterogeneous lenses in the sand domain. Water table fluctuation was also considered. In these cases, it was found that the heterogeneous lens was a barrier to LNAPL flow, and water table fluctuation stimulated the downward movement of retained LNAPL. The LNAPL flow and distribution observed in these numerical experiments show that in the subsurface environment, the behaviors of LNAPL highly depend on heterogeneities of unsaturated zone and the dynamic hydrogeologic condition such as water table fluctuation. These results can explain some of the complexity of LNAPL flow and distribution Patterns in LNAPL contaminated field sites.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.26 no.6
• /
• pp.1013-1020
• /
• 1997

To elicit the effect of fermentation on food quality of the watery Chinese cabbage pickles without fish sauce and red pepper paste(Baik-kimchi), changes in physicochemical properties and microstructure of fiber components were studied. Better water holding capacity(WHC) was showed in Baik-kimchi fermented at $25^{\circ}C$ than that of Baik-kimchi fermented at 5$^{\circ}C$. WHC measured at pH 2 and 6 were ranged from 10.18 to 16.79g/g dried sample for Baik-kimchi fermented at $25^{\circ}C$ and 6.51~14.58g/g dried sample for sample for samples at 5$^{\circ}C$, respectively. The higher WHC was resulted in pH controlled freeze-dried sample to pH 6 than that measured in pH 2 sample. The settling volume(SV) and oil adsorption capacity(OAC) increased with fermentation period and kept the same value for a little while, but slightly decreased in the over ripening period. Baik-kimchi fermented at $25^{\circ}C$ exhibited more shrunk microstructure of parenchyma cell and xylem than those of Baik-kimchi fermented at 5$^{\circ}C$. The appearance of SDF of the both Baik-kimchi ripened at 5$^{\circ}C$ and $25^{\circ}C$ could give granular shape, whereas the overripened Baik-kimchi had smooth surface of SDF. On the other hand, the IDF retained the original shape during fermentation.

• Environmental Engineering Research
• /
• v.23 no.2
• /
• pp.195-204
• /
• 2018

A pilot scale study was conducted on a down-flow hanging sponge (DHS) reactor installed at a sewage treatment plant in Banda Aceh, Indonesia for treatment of desludging septic tank wastewater. Raw wastewater with an average biochemical oxygen demand (BOD) and total suspended solids of 139 mg/L and 191 mg/L, respectively, was pumped into the reactor. Two different hydraulic retention times (HRTs, 3 h and 4 h) were investigated, equivalent to organic loadings of 1.11 and $0.78kg\;BOD/m^3/d$, respectively. The average BOD concentration in the final effluent was 46 and 26 mg/L at HRTs of 3 and 4 h, respectively. The concentration of retained sludge along the reactor height was 10.2-18.7 g VSS/L-sponge, and the sludge activities were 0.24-0.32 and 0.04-0.40 mg/g VSS/h for heterotrophs and nitrification, respectively. Values of water hold-up volume, dispersion coefficient, and number of tank in-series found from tracer studies of clean sponge and biomass-loaded sponge confirmed that growth of retained sludge on the sponge module improved hydraulic performance of the reactor. Adoption of the DHS reactor by this Indonesian sewage treatment plant would enhance the role of the current desludging septic tank wastewater treatment system.

• Journal of the Korean Society of Groundwater Environment
• /
• v.4 no.3
• /
• pp.144-152
• /
• 1997

In this study the experiment on water retention cure was conducted by using a volumetric pressure plate extractor for two different soils (SUS and KUS). When the volumetric pressure plate extractor is used, the volume of water removed from the soil sample at each increasing pressure step can be accurately measured and retained. When pressure values are subsequently reduced, the volume of water that returns to the soil can then also be accurately measured. The hysteresis effect of water retention curve was considered in the experiment. Parameters of water retention function were estimated by fitting experimental data with three proposed equations. Results of estimation showed that parameters of Gardner, Brooks-Corey and van Genuchten equations were found to be associated with air-entry value and width of size distribution. Consequently van Genuchten equation was proved to be best fined through the measured data points.

• Food Science and Preservation
• /
• v.30 no.4
• /
• pp.602-616
• /
• 2023

Fifteen types of rice collected from Kurdistan region-Iraq were investigated by principal component analysis (PCA) in terms of physical properties and cooking characteristics. The dimensions of evaluated grains correspond to 5.05-8.75 mm for length, 1.54-2.47 mm for width, and 1.37-1.95 for thickness. The equivalent diameter was in the range of 5.23-10.03 mm, and the area took 13.30-28.25 mm². The sphericity analysis values varied from 0.32 to 0.56, the aspect ratio from 0.17 to 0.39, and the volume of the grain was measured in the range from 4.48 to 17.74 mm³, hectoliter weight values were 730-820 kg/m³, and true density from 0.6 to 0.96 g/cm³. The broken grain ratio was 1.5-18.3%, thousand kernel weight corresponded to 15.88 to 22.42 g. The water uptake ratios for 30 min of soaking were increased at 60℃ compared to 30 and 45℃. The PCA was used to study the correlation of the most effective factors. Results of PCA showed that the first (PC1) and second (PC2) components retained 63.4% and 34.8% of the total variance, which PC1 was mostly related to hectoliter, broken ratio, and moisture content characteristics while PC2 was mostly concerned with hardness and true density. For cooking properties, the PC1 and PC2 retained 88.5% and 9.3% of the total variance, respectively. PC1 was mostly related to viscosity, spring value, and hardness after cooking, while PC2 was mostly concerned with spring value, hardness before cooking, and hardness after cooking.

• Journal of Ocean Engineering and Technology
• /
• v.2 no.2
• /
• pp.87-95
• /
• 1988

This paper is studied to know corrowive wear characteristics of austempered ductile cast ironin corrosive environments against mating SM45C hardened two test pieces in distilled water and NaCl aqueous solution. The corrosive wear mechanism was investigated by scanning electron microscopy and retained austenite volume fraction was investigated by X-ray diffractometer. The experimental result show that the corrosive wear characteristics depend largely on the $\textrm{Fe(OH)}_{3}$which is influenced by the critical sliding distance $L_{cr}$ and $L_{cr}$ shorted with increasing NaCl concentration. It was found that the carbides in matrix have a significant effect on their corrosive wear resisance and the fine acicular bainite showed corrosive wear resistance stronger than that of the coarse acicular and platelet bainite. From above results the model of corrosive wear mechanism in corrosive environments is proposed.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.12
• /
• pp.1311-1320
• /
• 2005

The purpose of this research is to survey characteristics of microbial community and the removal efficiency of organic materials for biological activated carbon in water treatment plant. Coal based activated carbon retained more attached bacterial biomass on the surface of the activated carbon than the other activated carbon with operating time and materials. The heterotrophic plate count(HPC), eubacteria(EUB) and 4,6-diamidino-2-phenylindole(DAPI) counts were ranged from $0.95{\times}10^7$ to $52.4{\times}10^7$ CFU/g, from $3.8{\times}10^8$ to $134.2{\times}10^8$ cells/g and from $7.0{\times}10^8$ to $250.2{\times}10^8$ cells/g, respectively. The biomass of EUB and DAPI appeared to be much more $10^2$ than HPC, which were increasing in bed volume of 20,000 at the stage of steady-state. The change of microbial community by analyzing fluorescent in situ hybridization(FISH) method with rRNA-targeted oligonucleotide probes, the dominant group was $\alpha$-proteobacteria($\alpha$ group) and high G+C content bacteria(HGC) the lowest distributing rate before reaching the bed volume of 20,000. After reaching the bed volume of 20,000, $\alpha$ group and other groups of bacteria became decreased, on the other hand, the proportion of both $\beta$-proteobacteria($\beta$ group) and $\gamma$-proteobacteri($\gamma$ group) were increasing. Coconut and wood based activated carbons had similar trend with coal based activated carbon, but the rate of $\alpha$ group on coal based activated carbon had gradually increased. Bacterial production with the operating period appeared highest in coal based activated carbon at the range of $1.2{\sim}3.4\;mg-C/m^3{\cdot}h$ while the coconut and wood based activated carbon were ranged from 1.1 to 2.6 $mg-C/m^3{\cdot}h$ and from 0.7 to 3.5 $mg-C/m^3{\cdot}h$ respectively. The removal efficiency of assimilable organic carbon(AOC) showed to be highly correlated with bacterial production. The correlation coefficient between removal efficiency of AOC and bacterial production were 0.679 at wood based activated carbon, 0.291 at coconut based activated carbon and 0.762 at coal based activated carbon, respectively.