• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.63 no.3
• /
• pp.212-217
• /
• 2014

The electric power output characteristics of magnesium fuel cell were investigated with regard to internal resistance. A equivalent circuit with the series-connected three internal resistance was introduced to analyze of the response to change of power. The power output analysis was employed in order to investigate the effect of internal resistances for the electrolyte concentration, air electrode area, Mg electrode area and distance between the electrodes. It was confirmed that internal resistance is generated by the electrolyte, air electrode and metal electrode, then those Internal resistances had a significant effect on the power output decrease. The power output was a maximum when the load resistance maches the internal resistance of the magnesium fuel cell. The fuel efficiency was only 50% at maximum power output. Higher fuel efficiency was achieved when the load resistance is greater than the internal resistance.

• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.961-966
• /
• 2004

Lateral ballast resistance is one of track components that causes much effects in track buckling. Ballast work or tie renewal if is done the ballast original lateral resistance lose. Reduction of lateral ballast resistance may significantly reduce the stability of track. Lateral ballast resistance that is decreased by these work increases slowly according to the increase of train passing tonnage. We measured the ballast lateral resistance in Okchon station neighborhood in Seoul-Busan line to grasp fluctuation phenomenon of ballast resistance by ballast class-2 work. The rate of decrease of ballast lateral resistance shortly after ballast work and the rate of increase by increase of train passing tonnage were investigated.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.8 no.2
• /
• pp.169-176
• /
• 2016

In this paper, further research is carried out to investigate the resistance encountered by an icebreaking vessel travelling through level ice and channel ice at low speed range. The present paper focuses on experimental and calculated ice resistances by some empirical formulas in both level ice and channel ice. In order to achieve the research, extra model tests have been done in an ice basin. Based on the measurements from model test, it is found that there exists a relationship between ice resistance, minimum ice load, maximum ice load and the standard deviation of ice load for head on operation in level ice. In addition, both level ice resistance and channel ice resistance are calculated and compared with model test results.

• Research in Plant Disease
• /
• v.26 no.1
• /
• pp.1-7
• /
• 2020

The succinate dehydrogenase inhibitor (SDHI) is a class of fungicides, which is widely and rapidly used to manage fungal pathogens in the agriculture field. Currently, fungicide resistance to SDHIs has been developed in many different plant pathogenic fungi, causing diseases on crops, fruits, vegetables, and turf. Understanding the molecular mechanisms of fungicide resistance is important for effective prevention and resistance management strategies. Two different mechanisms have currently been known in SDHI resistance. The SDHI target genes, SdhB, SdhC, and SdhD, mutation(s) confer resistance to SDHIs. In addition, overexpression of ABC transporters is involved in reduced sensitivity to SDHI fungicides. In this review, the current status of SDHI resistance mechanisms in phytopathogenic fungi is discussed.

• Journal of Welding and Joining
• /
• v.12 no.4
• /
• pp.127-140
• /
• 1994

Resistance spot welding has been widely used in the sheet metal joining processes because of its high productivity and convenience. In the resistance spot welding processes the size of molten nugget is a criterion to assess weld quality. Many research have founded on measuring weld nugget size at the same time monitoring welding process parameters such as dynamic resistance and electrode movement. With increasing demand of energy saving, many efforts were made to employ aluminum alloys that are lighter than steel and have relatively equivalent strength to steel in the automobile industry. In this paper, spot weldability of aluminum alloys for various welding conditions were examined by series of experiments. One of the 6000 series (Mg-Si) aluminum alloy, 6383-T4 was chosen, which is currently considered as a substitute for the galvanized steel. Dynamic resistance, electrode movement and corresponding nugget size were observed and compared to the case of steel. Finally, resistance spot welding of dissimilar material (galvanized steel-aluminum alloy) was attempted.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.493-496
• /
• 2003

Electrical characteristic of tracking resistance, volume resistance, insulation breaking strength etc. and mechanical characteristic are required to high voltage insulation insulator silicone rubber. Tracking resistance is adding much ATH to improve tracking resistance as the most important factor among them. But, there is problem that mechanical strength grows worse rapidly adding much ATH. Therefore, this research studied effect that flame retardant gets to tracking resistance during factor that influence to tracking resistance.

• Korean Journal Plant Pathology
• /
• v.10 no.4
• /
• pp.270-276
• /
• 1994

Mycelial growth resistant isolates of Botryosphaeria dothidea to benomyl showed 99~79% spore germination on the PSA media supplemented with 200~2,100 $\mu\textrm{g}$/ml of carbendazim and thiophanate-methyl to manifest the high cross-resistance in spore germination. Mycelial growth, 23~9 mm in colony diameter, also manifested the high cross-resistance of mycelial growth together with similarity of spore forming cross-resistance. Benomyl resistant isolates BR1, BR2 and BR3, grew 23~10 mm in colony diameter at 330~3,000 $\mu\textrm{g}$/ml of captafol, captan and oxine-copper showing the high double resistance of mycelial growth and spore formation with minor difference. However, within concentration range of the 3 fungicides tested, germinations of all the tested isolates were completely suppressed to show no double-resistance in the fungal spore germination.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.5
• /
• pp.661-669
• /
• 1986

In this study, the resistance spot welding process of an aluminum alloy was analyzed through the numerical simulation including the electric contact resistance and the heat generation in the electrode. The finite element model was used to solve the electro-thermal responses in weld cycles. The resistance of the contact area was represented as the contact element modeling, but the thermal resistance between the contact surfaces was neglected. Welding tests of Alclad 2024-T3 aluminum alloy were made not only to get the input data for the numerical simulation, but also to compare the numerical results. The contact resistance was determined initially by the contact resistance tests and assumed to decay exponentially up to the solidus temperature. The temperature distributions and dynamic resistance obtained numerically were in good agreement with the experimental results. Numerical results revealed that nugget growth depends mainly on the heat generated in the workpiece and its contact area. The heat generated in the electrode has, however, only a little effect on the nugget growth, and the heat generation in the electrode-workpiece interface is initially high but decrease repidly.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.41 no.3
• /
• pp.222-226
• /
• 2005

A series of model tests carried out at the CWC of WJFEL for the purpose of prediction of resistance for the performance and improvement of resistance by attaching appendage for the ship of 50 knots class planing hull. The resistance performance evaluation has been carried out for the bare hull and for the appendage hull with two different depth of vertical type wedges. In the bare model test, trim and sinkage is calculated for the planing hull and the resistance is calculated. For minimizing the resistance, wedge appendage is attached and tested. Analysis and tests shows that for a 12.5mm wedge, resistance is minimum and overall power tallied to 5636ps.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.7 no.5
• /
• pp.785-794
• /
• 2015

To obtain low resistance and high efficiency energy-saving ship, minimum total resistance hull form design method is studied based on potential flow theory of wave-making resistance and considering the effects of tail viscous separation. With the sum of wave resistance and viscous resistance as objective functions and the parameters of B-Spline function as design variables, mathematical models are built using Nonlinear Programming Method (NLP) ensuring the basic limit of displacement and considering rear viscous separation. We develop ship lines optimization procedures with intellectual property rights. Series60 is used as parent ship in optimization design to obtain improved ship (Series60-1) theoretically. Then drag tests for the improved ship (Series60-1) is made to get the actual minimum total resistance hull form.