• Advanced Composite Materials
• /
• v.16 no.4
• /
• pp.299-314
• /
• 2007

In the present study, natural fibers (jute, kenaf and henequen) reinforced thermoplastic (poly(lactic acid) and polypropylene) and thermosetting (unsaturated polyester) matrix composites were well fabricated by a compression molding technique using all chopped natural fibers of about 10 mm long, respectively. Prior to green composite fabrication, natural fiber bundles were surface-treated with tap water by static soaking and dynamic ultrasonication methods, respectively. The interfacial shear strength, flexural properties, and dynamic mechanical properties of each green composite system were investigated by means of single fiber microbonding test, 3-point flexural test, and dynamic mechanical analysis, respectively. The result indicated that the properties of the polymeric resins were significantly improved by incorporating the natural fibers into the resin matrix and also the properties of untreated green composites were further improved by the water treatment done to the natural fibers used. Also, the property improvement of natural fiber-reinforced green composites strongly depended on the treatment method. The interfacial and mechanical results agreed with each other.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.2
• /
• pp.444-450
• /
• 2011

A novel method that utilizes poly(5-methyl-2-thiozyl methacrylamide-co-2-acrylamido-2-methyl-1-propanesulfonic acid-co-divinylbenzene) [MTMAAm/AMPS/DVB] as a solid-phase extractant was developed for simultaneous preconcentration of trace Cd(II), Co(II), Cr(III), Cu(II), Fe(III), Mn(II), Ni(II), Pb(II), and Zn(II) prior to the measurement by flame atomic absorpiton spectrometry (FAAS). Experimental conditions for effective adsorption of the metal ions were optimized using column procedures. The optimum pH value for the simultaneously separation of the metal ions on the new adsorbent was 2.5. Effects of concentration and volume of elution solution, sample flow rate, sample volume and interfering ions on the recovery of the analytes were investigated. A high preconcentration factor, 100, and low relative standard deviation values, $\leq$1.5% (n = 10), were obtained. The detection limits (${\mu}gL^{-1}$) based on the 3s criterion were 0.18 for Cd(II), 0.11 for Co(II), 0.07 for Cr(III), 0.12 for Cu(II), 0.18 for Fe(III), 0.67 for Mn(II), 0.13 for Ni(II), 0.06 for Pb(II), and 0.09 for Zn(II). The validation of the procedure was performed by the analysis of two certified reference materials. The presented method was applied to the determination of the analytes in various environmental samples with satisfactory results.

• Proceedings of the Korean Society of Embryo Transfer Conference
• /
• 2002.11a
• /
• pp.108-108
• /
• 2002

포유동물의 암컷 생식기관에 존재하는 다양한 종류의 matrix metallo-proteinase (MMP)는 난소와 자궁의 구성성분의 주기적인 변화를 조절하며 이중 난소의 MMP는 난포의 성장과 배란 그리고 퇴화 동안 조직재구성에 매우 중요한 역할을 한다고 알려져 있다. 본 실험에서는 근래에 새로 발견된 사람의 난포액에 존재하는 분자량 약 110kDa인 MMP-2 isoform GA110을 동정하고 자 하였다. 난포액으로부터 GA110 단백질을 분리하기 위하여 난포액에 5mM ethylenediaminetetraacetic acid(EDTA)를 처리한 후 DEAE Sepharose Fast Flow를 이용한 chromatography를 시행하였다. 그 결과, 난포액 단백질들은 0.2M NaCl 의 분획에서 GA110 활성을 나타내었고 anti-human MMP-2 antibody에 대한 면역반응도 뚜렷이 나타났다. DEAE Sepharose Fast Flow에서 얻은 분획 중 GA110의 활성과 면역반응을 모두 나타내는 분획만을 모아 Gelatin Sepharose 4B affinity chromatography로 다시 분리하였다 분리한 결과 resin에 흡착된 단백질 (eluate) 분획들에서 매우 뚜렷한 GA110 gelatinase 활성을 나타내었으며 면역반응 또한 관찰되었다. 이 분획들의 단백질을 농축한 후 zymography를 시행하여 나타난 GA110 단백질 band를 잘라 내었으며 이로부터 단백질을 electroelution하여 농축한 후 reducing agent인 2-mercaptoethanol를 처리하였다. 이를 전기영동 후 MMP-2 (propeptide region) antibody를 사용하여 immunoblotting 한 결과 70-72kDa의 단백질만이 면역반응을 나타내었다. 마지막으로 위와 같이 준비된 70-72kDa 단백질의 아미노산 서열을 Edman degradation 방법으로 분석하였다. 그 결과 이 단백질의 N 말단의 10개의 아미노산 배열 순서가 알려진 사람의 proMMP-2의 전체 배열순서 중 propetide domain의 N 말단에서부터 다섯 번째에서 시작하여 10개의 아미노산의 서열과 정확하게 일치하였다. 위 결과들로 미루어 사람의 난포액에 존재하는 MMP-2의 새로운 isoform인 GA110은 70-72kDa의 ProMMP-2가 disulfide bond를 통해 homodimer 구조를 이루고 있는 것으로 여겨진다.

• The korean journal of orthodontics
• /
• v.41 no.6
• /
• pp.447-453
• /
• 2011

Objective: We compared the shear bond strength (SBS) of lingual retainers bonded to bovine enamel with three different resins using direct and indirect methods. Methods: Both ends of pre-fabricated twisted ligature wires were bonded to bovine enamel surfaces using Light-Core, Tetric N-Flow, or Transbond XT. Phosphoric acid-etched enamel surfaces were primed with One-Step prior to bonding with Light-Core or Tetric N-Flow. Transbond XT primer was used prior to bonding with Transbond XT. After 24 hours in water at $37^{\circ}C$, we performed SBS tests on the samples. We also assigned adhesive remnant index (ARI) scores after debonding and predicted the clinical performance of materials and bonding techniques from Weibull analyses. Results: Direct bonding produced significantly higher SBS values than indirect bonding for all materials. The SBS for Light-Core was significantly higher than that for Tetric N-Flow, and there was no significant difference between the direct bonding SBS of Transbond XT and that of Light-Core. Weibull analysis indicated Light-Core performed better than other indirectly bonded resins. Conclusions: When the SBS of a wire retainer is of primary concern, direct bonding methods are superior to indirect bonding methods. Light-Core may perform better than Transbond XT or Tetric N-Flow when bonded indirectly.

• Restorative Dentistry and Endodontics
• /
• v.20 no.1
• /
• pp.113-128
• /
• 1995

The purpose of this study was to investigate the effect of stannous fluoride on the dentin bonding with three kinds of commercially available dentin bonding systems containing different adhesive monomers. Dentin specimens with exposed labial dentin prepared from freshly extracted bovine mandibular anterior teeth were divided into experimental and control groups. The specimens of experimental groups were bonded with dentin bonding systems and composite resins including All bond 2 ㅡ& Bisfil, Scotchbond Multi-Purpose & Z100, and Denthesive II Charisma after 2 % stannous& fluorided application for S minutes and washing for 1 minute. The specimens of control groups were bonded with the same dentin bonding systems and composite resins as used in the experimental groups. After bonded specimens were stored in $37^{\circ}C$ distilled water for 24 hours, the tensile bond strength and cohesive failure rate were measured, and then the pretreated dentin surfaces and the fractured dentin surfaces were examined under scanning electron microscope. The results were as follows : Mean bond strength of stannous fluoride applied groups of All bond 2, Scotchbond MP, and Denthesive II were 2.5MPa, 1.1MPa, and 1.1MPa respectively, and those of control groups were 7.5MPa, 8.1MPa, and 4.6MPa. Bond strength values of stannous fluoride applied groups were significantly lower than those of the control groups(p<0.05). SEM findings of dentin surfaces after stannous fluoride application demonstrated an appearance of partially remained smear layer and smear plugs inspite of pretreatment with 10 % phosphoric aicd or maleic acid solution, and an appearance of smear layer covered surface under Denthesive II priming. But those of control groups commonly showed clean dentin surfaces without smear layer and smear plugs. On SEM observation of the fractured dentin-resin interface, while most of the specimens of stannous fluoride applied groups showed adhesive failure mode, those of All bond 2 and Scotchbond MP control groups showed mainly adhesive-cohesive mixed failure mode, and mainly adhesive failure mode in Denthesive II control group.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.15 no.1
• /
• pp.47-53
• /
• 2012

As one of the methods for recycling the FRP from the waste ships, separation of roving layer from the mat has some merits in a sense of the eco-friendly and economical recycling process. Similar characteristics, however, between the roving and the mat even with different ratio of the resin and the glass and the thickness of the roving, much thinner than the mat, make the mechanically automatic differentiation difficult. In this study spectrochemical differentiation between the two layers has been made using boiling concentrated sulfuric acid, methanol and isopropanol solution saturated with KOH, or hydrogen fluoride (HF) solution. Furthermore efficiently coloring water-soluble dye following the HF treatment makes the roving layer more distinguishable photophysically. The layer differentiation and the automatic layer distraction move up the date of simple and automatic separation process for the waste FRP.

• The Korean Journal of Pesticide Science
• /
• v.9 no.3
• /
• pp.185-190
• /
• 2005

Solid phase synthesis of 16, which is a derivative of the first systemic fungicide, carboxin 1 was described. Reaction of 1,3-oxathiolane derivative with solid resin of 4-hydroxy-3-nitrobenzophenone 6 gave 9 in 82% yield. Oxidation of sulfur in the solid 1,3-oxathiolane 9 by MCPBA followed by a ring expansion reaction under the acid catalyst afforded the corresponding dihydro-1,4-oxathiin derivative 12. Treatment of the solid 1,3-oxathiolane 9 with p-methoxyaniline resulted in 1,3-oxathiolane 14, 1,3-oxathiolane sulfoxide 15, dihydro-1,4-oxathiin 16, and acetoacetanilide derivative 17 in 41%, 35%, 14%, 10% yields, respectively.

• Applied Biological Chemistry
• /
• v.18 no.4
• /
• pp.188-193
• /
• 1975

The studies on the structure of anthocyanins in wild vines have beer carried out. The pigments were extracted with 0.5% HCl in methanol from the wild vines which were wildly grown in the mountain area of Korea and purified with Amberlite IRC-50 canon exchange resin. The individual pigments were separated by paper chromatography. Sever. pigments were identified by partial acid hydrolysis, sugar moiety, alkaline degradation, $R_f$ values of paper chromatography in various solvents and absorption spectra in the visible region. The identified pigments were delphinidin 3-monoglucoside, petunidin 3-monoglucoside, cyanidin 3-monoglucoside, delphinidin 3, 5-diglucoside, malvidin 3-monoglucoside, petunidin 3, 5 diglucoside and malvidin 3, 5-diglucoside.

• The Korean Journal of Mycology
• /
• v.16 no.3
• /
• pp.121-127
• /
• 1988

For selective purification of protein in Pleurotus cornucopiae (Per.) Rolland, affinity chromatography was performed by benzoyl-AH-Sepharose 4B gel synthesized using AH-Sepharose 4B with starting materials. Ligand capacity of benzoyl group was 9.3 micromole per milliliter of gel. Total apparent molecular weight of affinity protein was 255KD, which were protein complex of 29.5, 31.5 34.0, 71.0 and 89.0KD, respectively. The contents of nonpolar, polar, positively charged, and negatively charged amino acid were 45.68%, 26.93%, 11.81% and 15.58%, respectively. The nonpolar protein was selectively purified by hydrophobic ligand of benzoyl group of gel.

• The Journal of Advanced Prosthodontics
• /
• v.6 no.1
• /
• pp.8-13
• /
• 2014

PURPOSE. The purpose of this study was to evaluate whether surface treatments affect the translucency of laminate veneers with different shades and thicknesses. MATERIALS AND METHODS. A total of 224 disc-shaped ceramic veneers were prepared from A1, A3, HT (High Translucent) and HO (High Opaque) shades of IPS e.max Press (Ivoclar Vivadent) with 0.5 mm and 1.0 mm thicknesses. The ceramics were divided into four groups for surface treatments. Group C: no surface treatments; Group HF: etched with hydrofluoric acid; Group SB: sandblasted with 50-${\mu}m$ $Al_2O_3$; and Group L; irradiated with an Er;YAG laser. A translucent shade of resin cement (Rely X Veneer, 3M ESPE) was chosen for cementation. The color values of the veneers were measured with a colorimeter and translucency parameter (TP) values were calculated. A three-way ANOVA with interactions for TP values was performed and Bonferroni tests were used when appropriate (${\alpha}=0.05$). RESULTS. There were significant interactions between the surface treatments, ceramic shades and thicknesses (P=.001). For the 0.5-mm-thick specimens there were significant differences after the SB and L treatments. There was no significant difference between the HF and C treatments for any shades or thicknesses (P>.05). For the 1-mm-thick ceramics, there was only a significant difference between the L and C treatments for the HT shade ceramics (P=.01). There were also significant differences between the SB and C treatments except not for the HO shades (P=.768). CONCLUSION. The SB and L treatments caused laminate veneers to become more opaque; however, HF treatment did not affect the TP values. When the laminate veneers were thinner, both the shade of the ceramic and the SB and laser treatments had a greater effect on the TP values.