• Journal of the Korean Applied Science and Technology
• /
• v.32 no.3
• /
• pp.512-521
• /
• 2015

In this research, environmental friendly organic acid containing microetching system to improve adhesion strength between photoresist resin and Copper Clad Laminate(CCL) was developed without using strong oxidant $H_2O_2$. Etching rate and surface contamination on CCL were examined with various etching conditions with different etchants, organic acids and additives. to develope an optimum microetching condition. Etching solution with 0.04 M acetic acid showed the highest etching rate $0.4{\mu}m/min$. Etching solution with the higher concentration of APS showed the higher etching rate but surface contamination on CCL is very serious. In addition, stabilizer solution also played an important role to control the surface contamination. As a result of research, the etching solution containing 0.04 M of acetic acid, 0.1 M of APS with 4 g/L of stabilizer solution(ST-1) was best to improve adhesion between CCL and photoresist resin as well as showed the most clean and rough surface with the etching rate of $0.37{\mu}m/min$.

• Journal of Oral Medicine and Pain
• /
• v.39 no.3
• /
• pp.90-95
• /
• 2014

Purpose: To investigate viscosity and wettability of hyaluronic acid (HA) solutions according to supplementation of lysozyme and/or peroxidase, and different ionic strength and pH conditions. Methods: Solutions containing HA were prepared using distilled deionized water (DDW) and simulated salivary buffer (SSB) in different conditions. Different concentrations of hen egg-white lysozyme and bovine lactoperoxidase was added into HA solutions. HA solutions with antimicrobials in different ionic strength and pH conditions were prepared. Viscosity was measured using cone-and-plate digital viscometer at six different shear rates and wettability on acrylic resin and Co-Cr alloy was determined by contact angle. Results: The viscosity values of HA dissolved in DDW were decreased in order of HA, HA containing lysozyme, HA containing peroxidase, and HA containing lysozyme and peroxidase. The viscosity values for HA in DDW were decreased as the concentration of lysozyme and/or peroxidase increased. However, the viscosity values for HA in SSB showed no significant changes according to the concentration of lysozyme and/or peroxidase. The viscosity values of HA solutions were inversely proportional to ionic strength and pH. The contact angle of HA solutions showed no significant differences according to tested surface materials, addition of lysozyme and/or peroxidase, and different ionic strength and pH conditions. Contact angles on acrylic resin by HA solutions in all tested conditions were much higher than those by human saliva. Conclusions: The rheological properties of HA supplemented with lysozyme and/or peroxidase in different ionic strength and pH conditions were objectively confirmed, indicating the possibility of HA with lysozyme and/or peroxidase as main components in the development of effective saliva substitutes.

• The Journal of Advanced Prosthodontics
• /
• v.8 no.4
• /
• pp.290-295
• /
• 2016

PURPOSE. The aim of this study was to evaluate the effect of paracetic acid (PAA) and ozone disinfection on the tensile bond strength (TBS) of silicone-based resilient liners to acrylic resins. MATERIALS AND METHODS. One hundred and twenty dumbbell shaped heat-polymerized acrylic resins were prepared. From the mid segment of the specimens, 3 mm of acrylic were grinded off and separated parts were reattached by resilient liners. The specimens were divided into 2 control (control1, control7) and 4 test groups of PAA and ozone disinfection (PAA1, PAA7, ozone1 and ozone7; n=10). While control groups were immersed in distilled water for 10 min (control1) and 7 days (control7), test groups were subjected to PAA (16 g/L) or ozone rich water (4 mg/L) for 1 cycle (10 min for PAA and 60 min for ozone) per day for 7 days prior to tensile tests. Measurements of the TBS were analyzed using 3-way ANOVA and Tukey's HSD test. RESULTS. Adhesive strength of Mollosil decreased significantly by application of ozone disinfection. PAA disinfection had no negative effect on the TBS values of Mollosil and Molloplast B to acrylic resin. Single application of ozone disinfection did not have any negative effect on TBS values of Molloplast B, but prolonged exposure to ozone decreased its adhesive strength. CONCLUSION. The adhesion of resilient liners to acrylic was not adversely affected by PAA disinfection. Immersion in ozonated water significantly decreased TBS of Mollosil. Prolonged exposure to ozone negatively affects adhesion of Molloplast B to denture base materials.

• Food Science of Animal Resources
• /
• v.33 no.4
• /
• pp.501-507
• /
• 2013

Lysozyme was trapped from $2{\times}$ diluted egg white using Amberlite FPC 3500 ion exchange resin (1 g/10mL of egg white). The lysozyme bound to the resin was recovered using 0.1 N glycine-NaOH buffers, pH 9.0, containing 0.5 M NaCl. After separating lysozyme, the pH of the egg white solution was adjusted to 4.75 and centrifuged to remove interfering proteins. The supernatant was collected, added with 2.5% citric acid and 5.0% ammonium sulfate combination to precipitate egg white proteins, except for ovalbumin. After centrifugation, both supernatant (S1) and precipitant were collected. The precipitant was dissolved with 4 volumes of distilled water, and then 2.0% ammonium sulfate and 1.5% citric acid combinations added, stirred overnight in a cold room, and centrifuged. The resulting supernatant (S2) was pooled with the first supernatant (S1), desalted using an ultrafiltration unit, heat-treated at $70^{\circ}C$ for 15 min, and then centrifuged. The supernatant was collected as an ovalbumin fraction and lyophilized. The separated proteins were confirmed using Western blotting. The yield of lysozyme and ovalbumin was > 88.9% and > 97.7%, respectively, and the purity of lysozyme and ovalbumin was > 97% and 87%, respectively. The results indicated that the protocol was simple, and separated lysozyme and ovalbumin effectively.

• Korean Journal of Materials Research
• /
• v.27 no.12
• /
• pp.664-671
• /
• 2017

A composite material was prepared for the bipolar plates of phosphoric acid fuel cells(PAFC) by hot pressing a flake type natural graphite powder as a filler material and a fluorine resin as a binder. Average particle sizes of the powders were 610.3, 401.6, 99.5, and $37.7{\mu}m$. The density of the composite increased from 2.25 to $2.72g/cm^3$ as the graphite size increased from 37.7 to $610.3{\mu}m$. The anisotropy ratio of the composite increased from 1.8 to 490.9 as the graphite size increased. The flexural strength of the composite decreased from 15.60 to 8.94MPa as the graphite size increased. The porosity and the resistivity of the composite showed the same tendencies, and decreased as the graphite size increased. The lowest resistivity and porosity of the composite were $1.99{\times}10^{-3}{\Omega}cm$ and 2.02 %, respectively, when the graphite size was $401.6{\mu}m$. The flexural strength of the composite was 10.3MPa when the graphite size was $401.6{\mu}m$. The lowest resistance to electron mobility was well correlated with the composite with lowest porosity. It was possible the flaky large graphite particles survive after the hot pressing process.

• Restorative Dentistry and Endodontics
• /
• v.21 no.2
• /
• pp.569-584
• /
• 1996

The purpose of this study was to elucidate the effect of benzalkonium chloride on tensile bond strength of BPDM/HEMA dentin bonding. One hundred sixty dentin specimens from freshly extracted bovine mandibular incisors were used, and 0, 0.02, 0.1 or 0.5% benzalkonium chloride solution was applied to the dentin specimen with/after phosphoric acid. 32% phosphoric acid was used when the specimens were bonded with One-Step$^{TM}$, a BPDM/HEMA system and 10% was used when bonded with All-Bond$^{(R)}$ 2, a NTG-GMA/BPDM system. Aelitefil$^{TM}$ composite resin was bonded to the pretreated dentin specimen with the use of All-Bond$^{(R)}$ 2 or One-Step$^{TM}$ dentin bonding agent. After the bonded specimens were stored in $37^{\circ}C$ distilled water for 24 hours, tensile bond strength was measured. The fractured dentin specimens were examined under the scanning electron microscope. The results were as follows : Benzalkonium chloride application after acid-treatment resulted in decrease of dentin bond strength of One-Step$^{TM}$, a BPDM/HEMA system (p>0.05). Benzalkonium chloride application did not exert any influence on dentin bond strength of All-Bond$^{(R)}$ 2, a NTG-GMA/BPDM system (p>0.05). There was no relationship between the concentration or application method of benzalkonium chloride and the dentin bond strength of One-Step$^{TM}$ or All-Bon$^{(R)}$ 2 (p<0.05). On SEM examination of the fractured dentin-resin interface, while mixed failure was prominent in dentin bonding with One-Step$^{TM}$, adhesive and mixed failures were seen together in dentin bonding with All-Bond$^{(R)}$ 2 regardless of the concentration and application method of benzalkonium chloride.

• Polymer(Korea)
• /
• v.35 no.6
• /
• pp.548-552
• /
• 2011

Two functionalization methods, i.e., acid treatment and chemical amidation were performed to prepare the functionalized multi-walled carbon nanotubes (MWCNT), and the properties of epoxy/functionalized MWCNT composites were investigated and compared. Fourier transform infrared spectroscopy (FTIR) was used to confirm the surface functionality of the MWCNT obtained by the functionalization methods. The effects of the MWCNT functionalization on the interface and thermal conductivity were studied by zeta potential analyzer, scanning electron microscope and thermal conductivity analyzer. From these results, it was confirmed that the thermal conductivity of the epoxy/MWCNT composites could be increased by grafting with dodecylamine. This could be interpreted by relatively strong dispersion forces of the grafting MWCNT with dodecylamine in DGEBF epoxy resin. These results were in good agreement with the results that the zeta potential value of the grafting MWCNT with dodecylamine has a higher negative value than that of MWCNT with acid treatment.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.4
• /
• pp.432-443
• /
• 2017

Maltodextrin and citric acid are two types of natural materials with the potential as an eco-friendly binder. Maltodextrin is a natural substance rich in hydroxyl groups and can form hydrogen bonds with lignoselulosic material, while citric acid is a polycarboxylic acid which can form an ester bond with a hydroxyl group at lignoselulosic material. The combination of maltodextrin and citric acid as a natural binder materials supposed to be increase the ester bonds formed within the particleboard. This research determined to investigate the bonding properties of a new adhesive composed of maltodextrin/citric acid for nipa frond particleboard. Maltodextrin and citric acid were dissolved in distillated water at the ratios of 100/0, 87.5/12.5, 75/25 and 0/100, and the concentration of the solution was adjusted to 50% for maltodextrin and 60% citric acid (wt%). This adhesive solution was sprayed onto the particles at 20% resin content based on the weight of oven dried particles. Particleboards with a size of $25{\times}25{\times}1cm$, a target density $800kg/m^3$ were prepared by hot-pressing at press temperatures of $180^{\circ}C$ or $200^{\circ}C$, a press time of 10 minute and board pressure 3.6 MPa. Physical and mechanical properties of particleboard were tested by a standard method (JIS A 5908). The results showed that added citric acid level in maltodextrin/citric acid composition and hot-pressing temperature had affected to the properties of particleboard. The optimum properties of the board were achieved at a pressing temperature of $180^{\circ}C$ and the addition of only 20% citric acid. The results also indicated that the peak intensity of C=O group increased and OH group decreased with the addition of citric acid and an increase in the pressing temperature, suggesting an interreaction between the hydroxyl groups from the lignocellulosic materials and carboxyl groups from citric acid to form the ester groups.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.17 no.2
• /
• pp.136-143
• /
• 1988

This study was performed to provide the optimal conditions of quantitative analysis for free amino acid in fermented protein foods. The water extractable free amino acid from dairy fermented foods was extracted effectively at $75^{\circ}C$ for 40 min., while it were extracted from fermented soy products at $40^{\circ}C$ for 3 hours. A close results of free amino acid content to those from amino acid analyzer were obtained using OPDA method with lysine standard after deproteinizing with 1% picric acid. 95% ethanol used as a deproteinizing reagent could give a comparable results to those from picric acid treatment in determining free amino acid content using OPDA method. Therefore, ethanol treatment was more recommendable than picric acid treatment which has some troubles in removing excess picric acid through Dowex resin column. The most desirable precipitation method for free amino acid determination using TNBS method was 95% ethanol treatment among the various deproteinizing procedure. The copper salt method was not suitable owing to its lacking reproducibility and pronounced discrepancy in determining free amino acid.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.43 no.7
• /
• pp.1025-1035
• /
• 2014

This study assessed the effect of immobilized lipase on weak base styrene resin using polyethyleneimine (PEI) with cross-linking. Two procedures were used in this study. The first one, "mono-layer" lipase immobilization, involves washing PEI after adsorption. The second procedure, "multi-layer" lipase immobilization, has no washing before the cross-linking step. Treverlite XS-100200 (weak base styrene resin) was immersed with PEI solution (2.2 mg/mL). Lipase AH (from Burkholderia cepacia) was adsorbed onto the support coated with PEI before cross-linking with glutaraldehyde. Structured lipid was synthesized by immobilized lipase-catalyzed interesterification using canola oil, palmitic ethyl ester (PEE), and stearic ethyl ester (StEE). Total fatty acid contents of triacylglycerol (TAG) in structured lipids were analyzed to investigate activity, properties, and reusability of immobilized lipases. Activities of immobilized lipases on the multi-layer and mono-layer increased at a high concentration (8 mg/mL) of lipase solution used for immobilization. The results show that immobilized lipase with the mono-layer method at pH 8.0 on resin had the highest total saturated fatty acid content (26.17 area%). Activity of immobilized lipase with the multi-layer method at pH 7.5 on support was lower than that of the mono-layer, but total saturated fatty acid content was 16.79 area% higher than that of lipase AH (15.01 area%).