• Journal of the Korean Wood Science and Technology
• /
• v.34 no.4
• /
• pp.31-36
• /
• 2006

This study was conducted to improve the bond strength of plywood bonded with F/U molar ratio urea-formaldehyde (UF) resins modified with the selected FGMDI prepolymer contents for various purposes. The amount of FGMDI was mixed with liquid UF resin at 0 wt% (as control), 2 wt%, 5 wt%, 10 wt%, 25 wt%, and 50 wt% based on the resin solids. As results, in bonding strength, plywood with F/U molar ratio of 1.4 showed the highest value in Type 2 test and all molar ratio UF resins modified with over 25 wt% of the FGMDI showed more than $11kgf/cm^2$, which was satisfied the minimum requirement of KS standard, $7.5kgf/cm^2$, after Type1.5 testing. As F/U molar ratio was increased and the FGMDI addition in the UF resin was increased, average reduction rate of Type 1.5 bonding strength compared with Type 2 was significantly decreased.

• Journal of Korean Society on Water Environment
• /
• v.38 no.3
• /
• pp.133-142
• /
• 2022

Natural organic matter (NOM) is a heterogeneous mixture of organic matter with various polarities and molecular weights in an aquatic environment. This study investigated the effects of separation conditions (resin volume, organic matter, etc.) and the repeated use of the resin for the fractionation of organic components in the DAX resin fractionation method. The distribution characteristics of the organic components ((hydrophilic [Hi], hydrophobic acid [HoA], and hydrophobic neutral [HoN]) under the derived fractionation conditions were also analyzed. Constant fractionation results (i.e. HoA/Hi ratio) were obtained in the column capacity factor (i.e. the packed resin volume) in the range of 50 to 100. The resin-packed column maintained constant separation efficiency for up to two repeated uses. The above conditions were applied to wastewater and stream water samples (before and after rainfall). The results showed that the concentration of organic matter in the wastewater effluent was 2-15 times lower with an increased ratio of hydrophilicity to hydrophobicity (i.e. Ho/Hi) compared to the influent depending on the industrial wastewater classification. Particularly, HoN was found to have a high content distribution, 10.2-50.4% of the total dissolved organic matter (DOM), in the effluents. For the stream water, the content of Hi or HoN increased significantly after rainfall, suggesting a correlation with the distribution characteristics of pollutants from the stream watershed. The results provide useful data to enhance the reliability of the DAX resin fractionation and its application to environmental samples.

• Restorative Dentistry and Endodontics
• /
• v.34 no.1
• /
• pp.38-41
• /
• 2009

When we use the total-etch dentin adhesive system for composite resin restorations, gel or liquid acid etchant such as 37% phosphoric acid is commonly used. Thirty seven percentage phosphoric acid is very powerful erosive agent, and can cause severe harmful effects when it contacts with an oral mucosa and facial skin. This case describes iatrogenic chemical burn on facial skin caused by phosphoric acid which was happened during composite resin restorative procedure. Chemical burn by acid etchant can be evoked by careless handling of remnant and syringe. In order to prevent these iatrogenic injuries, we should check the complete removal of the etching agent both in intra and extra-oral environments after etching and rinsing procedure and it is necessary to use of the rubber dam or isolation instruments. If accidental burn were occurred. immediate wash with copious water. And bring the patient to the dermatologist as soon as possible.

• Journal of Korean Society of Forest Science
• /
• v.30 no.1
• /
• pp.19-29
• /
• 1976

The fiberboard and paper mills in this country are much affected by the price hikes and shortage of phenolic resins, since phenolic acid as a raw material depends on imported good. It is prerequisite to fiberboard industry to help replace with other sized and stabilize the prices and supply of them, improving the quality of boards. Thus, the present study was carried out to examine the effect of strength increasing sized such as urea formaldehyde resin (anion and cation type) and urea melamine copolymer resin, on the quality of the wet forming hardboard, and comparing them with two types of proprietary modified melamine resins, and ordinary size, phenol resin. The Asplund pulp was prepared from wood wastes mixed with 20 percent of lauan and 80 percent of pines as a fibrous material. After sizing agents were added at a pH of 4.5 for 10 minutes with alum in the beater, the stock was made in the form of wet sheet, prepared, and then performed by hot pressing cycle: $180^{\circ}C$, $50-6-5kg/cm^2$, 1-2-7 minutes. The properties of hardboard were examined after air conditioning. The results obtained are summarized as follows: 1. There is a significant difference in specific gravity among hardboards that were treated with strength increasing resins, but no difference is effected by the increase in the resin content. In the case of modified melamine resin, its specific gravity is highest. The middle group comprises cation type of urea resin, anion type of urea resin, and acid colloid of urea-melamine copolymer resin. The lowest is phenolic resin. 2. The difference of the moisture content of hardboard both by the resins and by the amount of each resin applied is significant. The moisture content of hardboard becomes lower along with the increase of each resin content, but there is no difference between 2 and 3 percent. 3. For water absorption, there is a significant difference both in the adhesives used and in the amount of paraffin wax emulsion. The water resistance becomes higher inn proportion to the content of the paraffin wax emulsion. To satisfy KS F standards of the water resistance, a proprietary modified melamine resin (p-6100) and modified cation type of urea resin (p-1500) do not require any paraffin wax emulsion, but in the case of anion type of urea resin, cation type of urea resin, and urea-melamine copolymer resin, 1 percent of paraffin wax emulsion is needed, and 2 percent of paraffin wax emulsion in the case of phenolic resin. 4. The difference of flexural strength of hardboard both by the resins and by the amount of each resin is significant. Modified melamine resin shows the highest degree of flexural strength. Among the middle group are urea-melamine copolymer resin, p-1500, anion type of urea resin, and cation type of urea resin. Phenolic resin is the lowest. The cause may be attributable to factors combined with the pressing temperature, sizing effect, and thermal efficiency of press platens heated electrically. 5. Considering the economic advantages and properties of hardboard, it is proposed that urea-melamine copolymer resin and cation type of urea resin be used for the development of the fiberboard industry. It is desirable to further develop the modified urea-melamine copolymer resin and cation type of urea resin through continuous study.

• Proceedings of the Korean Fiber Society Conference
• /
• 1993.06b
• /
• pp.90-94
• /
• 1993

• The Journal of Advanced Prosthodontics
• /
• v.5 no.1
• /
• pp.73-73
• /
• 2013

• Bulletin of the Korean Chemical Society
• /
• v.15 no.3
• /
• pp.179-181
• /
• 1994

• Journal of the Korean Chemical Society
• /
• v.6 no.1
• /
• pp.94-98
• /
• 1962

The polycondensates of isophthalic acid-cinnamic acid-glycerine system were synthesized. The molecular weights of these products were determined by two methods, viscosity method and osmotic pressure methods. In the synthesis of resin, the reaction temperature was kept at 232$^{\circ}C$ and the mole ratio of the reactants was chosen as follows: Glycerine ;1.0 Isophthalic acid ;1.0 Cinnamic acid ;2.8 Excessive cinnamic acid prevented gelation of reaction mixtures. As the solution became very dilute, reduced osmotic pressure P/C (at the concentration of solution below 0.24g/100 ml of acetone) and reduced viscosity ${\eta}_{sp}/C$ (at the concentration of solution below 0.32 g/100 ml of acetone) increased rapidly. The correspondence between molecular weights determined by the two methods made Huggin's equation applicable to the prepared polymer. The values of K and a are $2.77{\times}10^{-5}$ and 1.063, respectively.

• The Journal of the Petrological Society of Korea
• /
• v.21 no.4
• /
• pp.431-439
• /
• 2012

A column chemistry is the most useful tools for isolating the elements of interest in isotope geochemistry. Here we introduce the chemical experimental procedure for Sm, Nd, La and Ce separation such as Teflon powder or Ln-resin method using HDEHP of KIGAM, KBSI, KOPRI and ${\alpha}$-HIBA(${\alpha}$-Hydroxy Isobutyric acid) method of Nagoya University, Japan. This technical report will provide an useful information in selecting the experiment method for rare earth element isotope system study such as Sm-Nd and La-Ce isotope system.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.4
• /
• pp.615-626
• /
• 2016

In the paper, mild solvent soluble alkyl group modified epoxy resins were prepared via a three-step method; (1) the condensation reaction of dodecyl phenol (DP) and formaldehyde, (2) the crosslinking reaction of dodecyl phnol novolac compound (DPC) and bisphenol A diglycidyl ether, (3) the dodecyl phenol novolac epoxy resins containing fatty acid (DPFA) was prepared by introducing fatty acid to DPC. Equivalent ratios of DP and formaldehyde were 1.25~1.333/1.0. Equivalent ratio of DPC and bisphenol A diglycidyl ether (YD-128) was 1.0/2.0. Reactivity, viscosity, molecular weight, solvent solubility, and physical properties of DPFA were investigated. The result show that as the number of aromatic ring of DPFA increased, viscosity increased and solvent solubility improved. When we test the properties of coatings by blending the synthesized DPFA with a white pigment, DPFAC-5 using triphenylphosphine (TPP) as a ring-open catalyst showed optical performance for drying time, adhesion, hardness, impact resistance, acid resistance and storage stability.