• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.2
• /
• pp.190-197
• /
• 2002

In this thesis, ZnO varistors with various formulation, such as A∼E, were fabricated according to ceramic fabrication method. The microstructure, electrical properties, and surge characteristics of ZnO varistors were investigated according to ZnO varistors with various formulation. In the microstructure, A∼E\`s ZnO varistor ceramics sintered at 1130$\^{C}$ was consisted of ZnO grain(ZnO), spinel phase (Zn$\_$2.33/Sb$\_$0.67/O$\_$4/), Bi-rich phase(Bi$_2$O$_3$) and intergranuler phase, wholly. Lightning impulse residual voltage of A, B, C and E\`s ZnO varistors suited standard characteristics, below 12kV at current of 5kA. On the contrary, D\`s ZnO varistor exhibited high residual voltage as high reference voltage. In the accelerated aging test, leakage current and watt loss of B, C and D\`s ZnO varistors increases abruptly with stress time under the first a.c. stress(115$\^{C}$/3.213kV/300h). Consequently, C varistor exhibited a thermal run away. On the contrary, leakage current and watt loss of A and C\`s ZnO varistors which show low initial leakage current exhibited constant characteristics. After high current impulse test, A\`s ZnO varistor has broken the side of varistor but impulse current flowed. On the contrary, E\`s ZnO Varistor exhibited good discharge characteristics which the appearance of varistor was not wrong such as puncture, flashover, creaking and other significant damage. After long duration impulse current test, E\`s ZnO varistor exhibited good discharge characteristics which the appearance of varistor was not wrong such as puncture, flashover, creaking and other significant damage. After high current impulse test and long duration impulse current test, E\`s ZnO varistor exhibited very good characteristics which variation rate of residual voltage is 1.4% before and after test.

• Journal of Surface Science and Engineering
• /
• v.39 no.2
• /
• pp.49-56
• /
• 2006

In this study, the movable flame hardening process of 12Cr steel for a uniform hardness and desirable residual stress have been investigated. For this, the temperature cycles have been controlled accurately as a function of the three processing variables, the flame intensity $I_f$, the scanning velocity $V_s$, and the initial flame holding time $t_h$, where the standard surface temperature $T_{s,\;max}$, was maintained at $960^{\circ}C$. The optimized conditions were $V_s=0.68mn/s\;and\;t_h=67sec$ for the $C_3H_8:O_2\;=\;5:20l/min,\;V_s=0.80mm/s$ and $t_h=56sec$ for the $C_3H_8:O_2=6:24l/min,\;V_s=1.01mm/s\;and\;t_h=48sec$ for the $C_3H_8:O_2=7:28l/min,\;and\;V_s=1.15mm/s$ and $t_h=39sec$ for the $C_3H_8:O_2$=8:32 l/min. The optimally flame-hardened surface exhibited uniform distributions of the hardness and residual compressive stress over the treated area with moderate levels of $470{\sim}490HV_{0.2}$in hardness and $-300{\sim}-450MPa$ in residual stress, which were acceptable on the basis of the acceptance criteria of Siemens AG-KWU and GE Power Generation Engineering.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.8
• /
• pp.35-47
• /
• 2020

For permanent anchors used for slope reinforcement, bearing capacity and durability should be secured during the period of use. However, according to recent domestic and foreign studies, phenomena such as tension fractures, damage to anchorages, deformation and damage to slope and reduction of residual load over time have been reported along the long-term behavior of the anchors. These problems are expected to increase in the future, which will inevitably lead to problems such as increasing maintenance costs and relevant facility collapse. It is necessary to improve maintenance procedures and methods of ground anchors more practically. In this study, the problems and limitations of domestic maintenance methods were analyzed by conducting a literature study, and the measurement data of load cells installed on the install ground anchors were analyzed to determine the change in the residual load with regard to the elapsed date of the anchors. Based on the results, the effect of the construction conditions of anchors and the soil compositions on the increase and decrease of load were identified.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.30 no.6
• /
• pp.554-560
• /
• 2008

In posterior maxilla, it is difficult to achieve primary stability of implants due to sinus pneumatization, alveolar bone loss, and low bone quality. The accurate and objective primary stability assessment is important for good prognosis of implants. Purpose: The aim of this study was to assess the primary stability of the non-submerged, internal type implants with maxillary sinus augmentation using deproteinized bovine bone mineral by a resonance frequency analyzer, when residual alveolar bone height is under 8mm Materials and methods: A total of 20 implants was placed into 5 grafted maxillary sinuses in 5 patients. Deproteinized bovine bone mineral (Bio-$Oss^{(R)}$) was used as graft material. SS II implants (diameter 4.1mm, and length 11.5mm, SLA suface)) were placed. All of the patients received maxillary sinus graft procedure by 1-step technique. Residual bone height was $1.3{\sim}7.8mm$ (mean 4.4mm) measured by panorama radiography. After implant placement, RFA was measured at 4,8,12,20 weeks. The results were divided into 2 groups; RFA value under 4mm and over 5mm of bone height. It was statistically analyzed. Results: 1. The primary stability of implants was increased with time 2. The RFA value was above 65 ISQ at 12 weeks 3. There was no correlation between RFA and residual alveolar bone height in maxillary sinus augmentation by 1-step technique. Conclusion: 1-step surgical procedure is a feasible option for patients with as little as 4mm residual alveolar bone height, when utilizing non-submerged, internal type implants with xenografts.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.05a
• /
• pp.313-318
• /
• 2003

The development of new materials with light weight and high strength has become vital to the machinery, aircraft and auto industries. However, there are a lot of problems with developing such materials that require expensive tools, and a great deal of time and effort. Therefore, the improvement of fatigue strength and fatigue life are mainly focused on by adopting residual stress(in this thesis). The compressive residual stress was imposed on the surface according to each shot velocity(57, 70, 83, 96 m/sec) based on Shot-peening, which is the method of improving fatigue lift: and strength. By using the methods mentioned above, I arrived at the following conclusions 1. The fatigue crack growth rate(da/dN) of the Shot-peened material was lower than that of the Un-peened material. And in stage I, ${\Delta}K_{th}$, the threshold stress intensity factor, of the shot-peen processed material is high in critical parts unlike the Un-peened material. Also m, fatigue crack growth exponent and number of cycle of the Shot-peened material was higher than that of the Un-peened material. That is concluded from effect of da/dN. 2. Fatigue life shows more improvement in the Shot-peened material than in the Un-peened material. And compressive residual stress of surface on the Shot-peen processed operate resistance force of fatigue crack propagation.

• Korean Journal of Environmental Agriculture
• /
• v.41 no.2
• /
• pp.125-134
• /
• 2022

BACKGROUND: It is a very important task to block distribution of the agricultural products contaminated with pesticides in advance to protect consumers from residual pesticides among the agricultural products. Therefore, this study was performed to determine residual characteristics of pesticides in time-dependent manner and present scientific evidences for pre-harvest residue limit (PHRL) setting. METHODS AND RESULTS: The tested pesticides, chromafenozide and pyridalyl were sprayed onto the kale twice (seven day intervals) and then the plant samples were collected at 0 (after 3 hours), 1, 2, 3, 5, 7, and 10 days after the last spraying. Residual concentration of chromafenozide in kale decreased with 74.9% (of decreased fraction, field 1) and 85.3% (field 2) and pyridalyl decreased with 81.2% (field 1) and 85.8% (field 2), calculated by comparisons of the concentrations at 0 day and 10 days. Also biological half-lives of chromafenozide in kale were 5.6 day (field 1) and 3.4 day (field 2), and those of pyridalyl were 4.3 day (field 1) and 3.5 day (field 2). CONCLUSION(S): If the residues of chromafenozide and pyridalyl in kale from 10 days before harvest are less than 37.6 mg/kg and 58.9 mg/kg, respectively, it is expected that safe kale below MRL can be supplied on the pre-harvest day.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.1
• /
• pp.71-80
• /
• 2008

This paper presents the reusults of wide width tensile tests under sustained and cyclic loads with vairous loading rate on geogrids. A seires of modified wide width tensile tests were conducted to investigate the effect of tensile strain rate on the deformation behavior of the geogrids. In addition, residual deformation characteristics of a geogrid under sustained or cyclic tests were also investigated. The results indicated that the residual deformation of a geogrid is strongly related to the viscous behavior of the geogrid, and the residual deformation can be well described by a hyperbolic curve. Also revealed was that residual deformation of a geogrid when subject to sustained or cyclic load should be described with the framework of viscous behavior.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.19 no.2
• /
• pp.102-108
• /
• 2023

A Chloride-induced stress corrosion cracking (CISCC) of austenite stainless steel in dry cask storage system (DCSS) can occur with extending service time than originally designed. Cold spray coating (CSC) not only form a very dense microstructure that can protect from corrosive environments, but also can generate compressive stress on the surface. This characteristic of CSC process is very helpful to increase the resistance for CISCC. CSC with several powders, such as 304L, 316L and Ni can be optimized to form very dense coating layer. In addition, the impact energy generated as the CSC powder collides with the surface of base metal at a speed of Mach 2 or more can remove the residual tensile stress of welding area and serve the compress stress. CSC layers include no oxidation and no contamination with under 0.2% porosity, which is enough to protect from the penetration of corrosive chloride. Therefore, the CSC coating layer can be accompanied by a function that can be disconnected from the corrosive environment and an effect of improving the residual stress that causes CISCC, so the canister's CISCC resistance can be increased.

• Korean Journal of Logic
• /
• v.15 no.1
• /
• pp.85-107
• /
• 2012

This essay criticizes Van Fraassen's argument for empirical equivalence among competing theories, which is based on his interpretation of Newtonian space-time. I argue that his misleading interpretation of the ontology of absolute space-time results in his ineffective attacks against a residual structure of space-time, absolute velocity. Van Fraassen's argument basically misleads us into empirical equivalence in that his literal reading of Newtonian space-time disregards a variety of aspects of its model.

• Korean Journal of Weed Science
• /
• v.11 no.1
• /
• pp.50-59
• /
• 1991

Residual period and carry-over effect of some herbicides were determined using a bioassay method in six summer crops(potato, carrot, corn, water melon, soybean, and sesame). The effects were measured at regular time intervals after applying different rates of the herbicides. There were no great differences in residual period and carry-over injury between the soils and kinds of crops used. However, the residual period varied with the herbicides studied and the carry-over injury was dependent upon season and rate of the herbicide application, sampling depth of soil, and kind and seeding date of the test plant. When the residual herbicides were applied, the carry-over injury could be minimized by selecting tolernet crops, delaying seeding of the crops after application of the herbicides, and regulating the cultivation depth. Herbicides which showed no residual effect by the end of the cropping period(100-120 days for summer crops) and no carry-over effect were alachlor, trifluralin, ethalfluralin, metribuzin, and prometryn. When pendimethalin, metolachlor, linuron, methabenzthiazuron, and simazine were applied at the recommended rate or less, there was no carry -over injury at harvesting time. With doubling the recommended rate, however, the carry-over effect was found in sensitive crops. Napropamide applied at the rate of 300 g a.i./10 a brought about carry-over injury for Italian ryegrass and barley at 140 days in summer crops, whereas the injury was not found in Cruciferae (radish, Chinese cabbage). Nitralin applied at the rate of 150-300 g a.i./10a caused the carry-over injury for Italian ryegrass and barley at 140 days in summer crops. However, there was no injury for Cruciferae.