• Journal of the Korea Institute of Military Science and Technology
• /
• v.15 no.5
• /
• pp.550-556
• /
• 2012

In this study, a series of ballistic experiments have been performed to investigate the protection mechanism of some inert reactive cassettes against shaped charge jet. Three kinds of material were tested as a core material of the inert cassettes, i.e. one of rubber materials, a high modulus and high strength composite material used for ballistic protection and a mixture of energetic materials. Parameters such as deformation of the cassettes, occurrence time of jet distortion, leading jet length and residual penetration depth were investigated from the experiments and they were compared to each other quantitatively according to the jet incidence angles. The results show that the increment of cassette deformation caused jet distortion to occur early and jet distortion brought decrease of the length of leading jet. Then the decrease of the length of leading jet accompanied the decrease of residual penetration depth.

• Journal of Positioning, Navigation, and Timing
• /
• v.5 no.1
• /
• pp.1-9
• /
• 2016

Range-based wireless localization system must measure accurate range between a mobile node (MN) and reference nodes. However, non-line-of-sight (NLOS) error caused by the spatial structures disturbs the localization system obtaining the accurate range measurements. Localization methods using the range measurements including NLOS error yield large localization error. But filter-based localization methods can provide comparatively accurate location solution. Motivated by the accuracy of the filter-based localization method, a filter residual-based NLOS error estimation method is presented in this paper. Range measurement-based residual contains NLOS error. By considering this factor with NLOS error properties, NLOS error is mitigated. Also a process noise covariance matrix tuning method is presented to reduce the time-delay estimation error caused by the single dynamic model-based filter when the speed or moving direction of a MN changes, that is the used dynamic model is not fit the current dynamic of a MN. The presented methods are evaluated by simulation allowing direct comparison between different localization methods. The simulation results show that the presented filter is more accurate than the iterative least squares- and extended Kalman filter-based localization methods.

• Korean journal of food and cookery science
• /
• v.15 no.4
• /
• pp.363-369
• /
• 1999

The study was carried out to compare the reaction rate of caramel type browning reaction of xylose(XY), glocose(GL), sucrose(SU), glucose+citric acid(GLCA), glucose+sodiumcitrats(GLSC), glucose+glycine(GLGC) heated at 60, 80, 100, 120 and 140$^{\circ}C$ for 24 hours, respectively. 1. The color intensity (absorbance at 490 nm) of the browning reaction mixtures tends to increase as the browning reaction time gets longer and the browning of reaction temperature gets higher. But the degree of the intensity of SU and GLCA changes very little. 2. The reaction rate constant (K) was increased rapidly above 120$^{\circ}C$ and appeared maximum at 140$^{\circ}C$, especially GLGC (140.25) was the highest. The activation energy (Ea) of sugars. XY had the highest value (124.36 J/mol), while SU the lowest(104.68 J/mol). Mixtures of GLGC was shown to have higher activation energy (144.94 J/mol) than the sugar alone and Q$\_$10/ values of GLGC were 1.68-2.85. 3. The residual amount of reactants such as xylose, glucose, sucrose, citric acid, sodium citrate and glycine in each browning mixture were decreased upon the browning reaction temperature increasing. In the GLCA, GLSC and GLGC browning mixtures, respectively, the residual amounts of glucose were less than those with amino acid, organic acid and their salt.

• Steel and Composite Structures
• /
• v.32 no.2
• /
• pp.265-279
• /
• 2019

The self-centering capacity and energy dissipation performance have been recognized critically for increasing the seismic performance of structures. This paper presents an innovative steel moment frame with self-centering steel reinforced concrete (SRC) wall panel incorporating replaceable energy dissipation devices (SF-SCWD). The self-centering mechanism and energy dissipation mechanism of the structure were validated by cyclic tests. The earthquake resilience of wall panel has the ability to limit structural damage and residual drift, while the energy dissipation devices located at wall toes are used to dissipate energy and reduce the seismic response. The oriented post-tensioned strands provide additional overturning force resistance and help to reduce residual drift. The main parameters were studied by numerical analysis to understand the complex structural behavior of this new system, such as initial stress of post-tensioning strands, yield strength of damper plates and height-width ratio of the wall panel. The static push-over analysis was conducted to investigate the failure process of the SF-SCWD. Moreover, nonlinear time history analysis of the 6-story frame was carried out, which confirmed the availability of the proposed structures in permanent drift mitigation.

• KEPCO Journal on Electric Power and Energy
• /
• v.4 no.2
• /
• pp.89-99
• /
• 2018

Downtime and malfunction of industrial rotor machines represents a crucial cost burden and productivity loss. Fault diagnosis of this equipment has recently been carried out to detect their fault(s) and cause(s) by using fault classification methods. However, these methods are of limited use in detecting rotor faults because of their hypersensitivity to unexpected and different equipment conditions individually. These limitations tend to affect the accuracy of fault classification since fault-related features calculated from vibration signal are moved to other regions or changed. To improve the limited diagnosis accuracy of existing methods, we propose a new approach for fault diagnosis of rotor machines based on the model generated by supervised learning. Our work is based on feature residual values from vibration signals as fault indices. Our diagnostic model is a robust and flexible process that, once learned from historical data only one time, allows it to apply to different target systems without optimization of algorithms. The performance of the proposed method was evaluated by comparing its results with conventional methods for fault diagnosis of rotor machines. The experimental results show that the proposed method can be used to achieve better fault diagnosis, even when applied to systems with different normal-state signals, scales, and structures, without tuning or the use of a complementary algorithm. The effectiveness of the method was assessed by simulation using various rotor machine models.

• Nuclear Engineering and Technology
• /
• v.54 no.3
• /
• pp.1136-1144
• /
• 2022

The effects of nearby residents and the public by the residual contamination from the decommissioning of nuclear facilities should comply with the dose criteria, and whether additional remediation action is necessary from the ALARA perspective must be determined. Therefore, we analyzed the requirements of ALARA action levels and performed preliminary ALARA evaluation. The ratio of residual contamination concentration to DCGL was calculated for the basement fill and the building occupancy mode. The results showed that the additional remediation actions below DCGL are not justified. In addition, we analyzed the effect of remediation area. It was noted that the increase of the remediation area showed a positive correlation with the Conc/DCGL value in the basement fill mode. On the other hand, in the building occupancy mode, since the floor area of the building is the target of remediation and has the effect of increasing the same as the evaluation area of the building occupants, but due to the difference in the amount of increase, the Conc/DCGL showed a negative correlation. We expect the approach and method of ALARA evaluation can be utilized for concrete cost-benefit calculation during the decommissioning or at the time of remediation.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2000.09a
• /
• pp.522-529
• /
• 2000

We present a new procedure to evaluate the residual life of 1Cr-1Mo-0.25V steel by reversible magnetic permeability. The method is based on the existence of the first harmonics in the differential magnetization around the coercive force. The apparatus is based on the detection of the voltage induced in a coil using a lock-in amplifier tuned to a frequency of the exciting one. Results obtained for the first harmonics and Vickers hardness on the aged samples show that the peak interval of reversible permeability and Vickers hardness decrease as ageing time increases. The correlation between Vickers hardness and the peak interval of the reversible permeability could well be used to evaluate the residual life of 1Cr-1Mo-0.25V steel, nondestructively.

• Nuclear Engineering and Technology
• /
• v.55 no.12
• /
• pp.4335-4349
• /
• 2023

Nuclear marine propulsion has been emerging as a next generation carbon-free power source, for which proper passive residual heat removal systems (PRHRSs) are needed for long-term safety. In particular, the characteristics of unlimited operation time and compact design are crucial in maritime applications due to the difficulties of safety aids and limited space. Accordingly, a compact and long-term-operable PRHRS has been proposed with the key design concept of using both air cooling and seawater cooling in tandem. To confirm its feasibility, this study conducted system design and a transient analysis in an accident scenario. Design results indicate that seawater cooling can considerably reduce the overall system size, and thus the compact and long-term-operable PRHRS can be realized. Regarding the transient analysis, the Multi-dimensional Analysis of Reactor Safety (MARS-KS) code was used to analyze the system behavior under a station blackout condition. Results show that the proposed design can satisfy the design requirements with a sufficient margin: the coolant temperature reached the safe shutdown condition within 36 h, and the maximum cooling rate did not exceed 40 ℃/h. Lastly, it was assessed that both air cooling and seawater cooling are necessary for achieving long-term operation and compact design.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.27 no.4
• /
• pp.437-447
• /
• 2011

In patients who used removable partial dentures for a long period of time, gradual alveolar bone resorption occurs in edentulous area. However, in residual teeth area, alveolar bone is maintained sound. This causes an imbalance in intermaxillary distance between a maxillae and a mandible which is intensified due to expansion in vertical and horizontal bone amount difference between the two area as time passes. As the result, this shows a substantial difference in vertical position according to the period of teeth loss even after residual teeth loss. As in this situation, a patient with bilaterally and anterio-posteriorly different intermaxillary distance, various prosthodontic problems can be caused in fixed implant prosthodontics and implant overdenture. This study shows a case in which implant-supported removable partial denture was fabricated considering residual alveolar bone height after teeth loss in a patient who had been using a distal extension removable partial denture for a long period of time. In anterior area with short intermaxillary distance, fixed prosthodontics were fabricated with implant placement and in posterior area with long intermaxillary distance, a removable partial denture was fabricated. Finally, a small number of implants were placed without additional surgery and economical and comfortable treatment results were shown.

• The Korean Journal of Food And Nutrition
• /
• v.21 no.4
• /
• pp.499-509
• /
• 2008

The purpose of this study was to investigate the changes in physicochemical and sensory properties of raw fruits during washing and chlorine treatments. Strawberry and banana were pre-prepared at different concentration of chlorinated water(0 ppm, 50 ppm and 100 ppm), immersion time(3 min and 5 min), and number of post-rinsing(1 time, 2 times and 3 times). The physicochemical properties such as pH, sugar contents, residual chlorine contents, color values and hardness of the fruits were analyzed, and the sensory quality were evaluated throughout the sterilization treatment process. After washing strawberry with 100 ppm chlorinated water and 3 times of post-rinsing, pH and residual chlorine contents were showed a little difference, while sugar contents, hardness, and color values(L, a and b) were reduced. In case of banana, pH, sugar contents and residual chlorine contents were not affected, and hardness and L color value were reduced. However, a and b color values of banana were gradually increased as the development of brown discoloration. Sensory properties of the samples were affected by the chlorine sterilization treatment. In overall acceptance, strawberry and banana treated with 100 ppm chlorinated water showed the lowest scores among treatments. Therefore it could be suggested that the application of 50 ppm chlorinated water for $3{\sim}5$ minutes with over 3 times of post-rinsing was the effective pre-preparation method without affecting the quality of the fruits.