• The Korean Journal of Ceramics
• /
• v.2 no.1
• /
• pp.11-18
• /
• 1996

The variation of electrical conductively and Seebeck coefficient of FeSi2 according to the density of the specimen has been observed over the temperature range 50 to $700^{\circ}C$. A conventional pressureless sintering method with various sintering time (0, 0.5, 1, 5h) at $1190^{\circ}C$ and/or various sintering temperatures(1160, 1175, 1190, $1200^{\circ}C$) for 2 h was carried out to prepare $FeSi_2$ specimens having various densities. The relationship between the electrical conductivity and Seebeck coefficient was investigated after two steps of annealing (at $865^{\circ}C$ and then $800^{\circ}C$ for total 160h) and thermoelectric measurement. The electrical conductivity for the specimens showed a typical tendency of semiconductor, the average activation energy of which in the intrinsic region (above $300^{\circ}C$) was observed approximately as 0.452 eV, and increased slightly with density. On the other hand, the specimen of the lower density showed the higher value of Seebeck coefficient in the intrinsic region. As the temperature fell into the non-degenerate region, the highly densified specimen which had relatively little residual metal phase showed the higher value of Seeback coefficient. The power factor of all specimens showed the optimum value at $200^{\circ}C$. However, the power factor of the specimen of the lower density increased again from $400^{\circ}C$ and that of the higher dense specimen increased from $500^{\circ}C$. The power factor was more affected by Seebeck coefficient than electrical conductivity over all temperature range.

• Journal of The Korean Dental Society of Anesthesiology
• /
• v.1 no.1 s.1
• /
• pp.26-31
• /
• 2001

The wide deep penetrating wound of maxillofacial region should be early closed under emergency general anesthesia for the prevention of complications of bleeding, infection, shock & residual scars. But, if the emergency general anesthesia wound be impossible because of pneumoconiosis, obstructive pulmonary disease & hypovolemic shock, early primary closure should be done under local anesthesia by use of much amount of the anesthetic solution. The maximum dose of dental lidocaine (2% lidocaine with 1 : 100,000 epinephrine) is reported to 7 mg/kg under 500 mg (13.8 ampules) in normal adult. But the maximum permissible dose of dental lidocaine can be changed owing to the general health, rapidity of injection, resorption, distribution & excretion of the drug. The blood level of overdose toxicity is above $4.0{\mu}g/ml$ in central nervous & cardiovascular system. The injection of dental lidocaine 1-4 ampules is attained to the blood level of $1{\mu}g/ml$ in normal healthy adult. The duration of anesthetic action in the dental 2% lidocaine hydrochloride with 1 : 100.000 epinephrine is 45 to 75 minutes and the period to elimination is about 2 to 4 hours. Therefore, authors selected the following anesthetic methods that the first injection of 6 ampules is applied into the deeper periosteal layer for anesthetic action during 1 hour, the second injection into the deeper muscle & fascial layer, the third injection into the superficial muscle and fascial layer, the fourth injection into the proximal skin & subcutaneous tissue and the fifth final injection into the distal skin & subcutaneous tissue. The total 26-28 ampules of dental lidocaine were injected into the wound as the regular time interval during 5-6 hours, but there were no systemic complications, such as, agitation, talkativeness, convulsion and specific change of vital signs and consciousness.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.329-329
• /
• 2008

To date, rubbing has been widely used to align LC molecules uniformly. Although rubbing can be simple, it has fundamental problems such as the generation of defects by dust and static electricity, and difficulty in achieving a uniform LC alignment on a large substrate. Therefore, noncontact alignment has been investigated. Ion beam induced alignment method, which provides controllability, nonstop process, and high resolution display. In this study, we investigated liquid crystal (LC) alignment with ion beam (IB) that non contact alignment technique on polyimide and electro-optical characteristics of twisted nematic (TN)-liquid crystal display (LCD) on the poly imide under various ion beam angles. In this experiment, Polyimide layer was coated on glass by spin-coating and Voltage-transmittance(VT) and response time characteristics of the TN cell were measured by a LCD evaluation system. The good characteristics of the nematic liquid crystal (NLC) alignment with the ion beam exposure poly imide surface was observed. The tilt angle of NLC on the PI surface with ion beam exposure can be measured under $1^{\circ}4 for all of irradiation angles. In addition, it can be achieved the good ED properties, and residual DC property of the ion beam aligned TN cell on polyimide surface.

• Journal of Broadcast Engineering
• /
• v.20 no.3
• /
• pp.414-420
• /
• 2015

The quality of depth images is important in the 3D video system to represent complete 3D contents. However, the original depth image from a depth camera has a low resolution and a flickering problem which shows vibrating depth values in terms of temporal meaning. This problem causes an uncomfortable feeling when we look 3D contents. In order to solve a low resolution problem, we employ 3D warping and a depth weighted joint bilateral filter. A temporal mean filter can be applied to solve the flickering problem while we encounter a residual spectrum problem in the depth image. Thus, after classifying foreground andbackground regions, we use an upsampled depth image for a foreground region and temporal mean image for background region.Test results shows that the proposed method generates a time consistent depth video with a high resolution.

• Journal of Broadcast Engineering
• /
• v.18 no.4
• /
• pp.631-642
• /
• 2013

For the emerging High Efficiency Video Coding (HEVC) standard, a fast transform unit (TU) decision method is proposed. HEVC defines the TU representing a region sharing the same transformation, and it allows a residual block to be split into multiple TUs recursively to form a quadtree. By using the quadtree of TUs, HEVC supports various transform sizes from $4{\times}4$ to $32{\times}32$. The various sizes of TUs can provide a good coding efficiency, whereas this may increase encoding complexity dramatically. In the assumption that a TU with highly compacted energy is unlikely to be split, the proposed method determines TU sizes according to the position of the last non-zero transform coefficient. In the experimental results, the proposed method reduced 18% encoding run time with the negligible coding loss of 0.7% BD-rate for the Random_access case.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.12
• /
• pp.2565-2573
• /
• 2002

A basic research was performed to ensure the usefulness of Small Punch-creep(SP-creep) test for residual life evaluation of heat resistant components effectively. This paper presents analytical results of initial stress and strain distributions in SP specimen caused by constant loading for SP-creep test and its experimental correlations with uniaxial creep(Ten-creep) test on 9Cr1MoVNb steel. It was shown that the initial maximum equivalent stress, ${\sigma}_{eq{\cdot}max}$ from FE analysis was correlated with steady-state equivalent creep strain rate, ${\epsilon}_{qf-ss'}$ rupture time, $t_r$, activation energy, Q and Larson-Miller Parameter, LMP during SP-creep deformation. The simple correlation laws, ${\sigma}_{sp}-{\sigma}_{TEN}$, $P_{sp}-{\sigma}_{TEN}\; and\; Q_{sp}-Q_{TEN}$ adopted to established a quantitative correlation between SP-creep and Ten-creep test data. Especially, the activation energy obtained from SP-creep test is linearly related to that from Ten-creep test at $650^{\circ}C$ as follows : $Q_{SP-P}\;{\risingdotseq}\;1.37 \;Q_{TEN},\; Q_{SP-{\sigma}}{\risingdotseq}1.53\; Q_{TEN}$.

• Journal of Mushroom
• /
• v.10 no.1
• /
• pp.44-48
• /
• 2012

In this study, whether Giemsa staining solution can accurately determine bacterial contamination of liquid spawn for Flammulina velutipes in a short period of time was investigated. Giemsa solution staining cells of blood, bone marrow, lymph node, malaria parasites, rickettsia et al. was prepared by dissolving basic methylene azul and methylene blue, and acidic eosine in methyl alcohol-glycerine. Supernatant samples of Flammulina velutipes liquid spawn cultured under explosive aeration were placed on a slide, mixed with Gimesa solution and examined with optical microscope after staining. In 40 to 60 seconds bacterial cells were distinguishable from soybean meal residual and hyphal cell fragments. Thus we conclude that microscopy using Gimesa staining solution is a quick, simple and accurate method for the mushroom growers to effectively use to detect bacterial contamination of the liquid spawn.

• Journal of Information Technology Application
• /
• v.3 no.2
• /
• pp.67-82
• /
• 2001

The ILOF project addresses the needs of logistics industrial organizations to reduce information processing time, improve added and residual value of information and reduce processing and transportation costs. It deals with the information supply chain information systems shared by vertical partner as important entity, whose performance and optimization very significantly affects the efficiency and performance of logistics industries. This paper deals with logistics information exchange systems based on supply chain management, focusing on sharing database and processes between partners such as shipper, logistics broker, transportation company, shipping company etc., for smoothing the information flow, enhancing consumer service and reducing communication fee and labour costs. The significance of contribution of this research is the provision of a model for logistics information exchange including entity relationship diagram, data flow diagram and functions which is able to facilitate the formulation of a customer driven supply chain information network, there by enhancing the competitive edge of companies in logistics industries on local and global basis.

• Korean journal of food and cookery science
• /
• v.4 no.1
• /
• pp.27-32
• /
• 1988

The almost similar degumming effect was obtained by using oxalic acid instead of phosphoric acid, which also improves waste-water treatment. At this point, solution of Phosphoric, Acetic, Citric, Oxalic, and Nitric acid were used for degumming of rapeseed and soybean oil. Compared with Phosphoric(PA) and Oxalic acid(OA) were showed a simillar degumming effect in these vegetable oils. In rapeseed oil of 85% PA treating group and 5,10% OA fretting group, residual soap and phosphorus content in neutralized oil, color in bleached oil, and peroxide value and fatty acid content in deodrized oil were showed to simillar result. Soybean oil as well as rapeseed oil were showed to similar result. As a result, we could comfirmed substitutive possibility, which change PA into OA as a degumming agent. In the other hand, waste waters were obtained from 55% PA treating group and 10% OA treating group. Analytical result for this waste waters has showed a wide difference, especially in the BOD and COD. The amount of treating agents and time required in the precipitation seperation and chemical treatment each 3 and 1.7 times, which is PA treating group than OA treating group. We have investigated both the simillar degumming effect by OA solution and an alternative the pollution program means of a chemical treatment process is not possible.

• Fire Science and Engineering
• /
• v.20 no.1 s.61
• /
• pp.71-76
• /
• 2006

The major causes of electrical fire are classified to short circuit fault, overload fault, electric leakage and electric contact failure. The occurrence factor of the fire is electric arc or spark accompanied with electrical faults. Residual Current Protective Device(RCD) of high sensitivity type used at low voltage wiring cuts off earth leakage and overload, but the RCD can't cut off electric arc or spark to be a major factor of electrical fire. As the RCDs which are applied low voltage distribution panel are prescribed to rated breaking time about 30[ms](KS C 4613), the RCDs can't perceive to the periodic electric arc or spark of more short wavelength level. To be improved on such problem, this paper is proposed to a auxiliary control apparatus for RCD trip on electric arc or spark due to electrical fire. Some experimental results of the proposed apparatus is confirmed to the validity of the analytical results.