• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.5
• /
• pp.303-310
• /
• 2014

This study investigated the reduction of food waste through the slurry phase decomposition in a source of food waste by microorganisms. The reactor used in the experiment was composed of both woodchip with wood material and sponges with polyurethane material as media of attached microorganisms, and food waste was mixed with a constant cycle consisted of a stirring device. During the experimental period of 100 days, the change in weight over the cumulative total amount of food waste added was reduced by 99%. Approximately, 1% of the residual food waste could be inherently recalcitrant materials (cellulose, hemicellulose, lignin, etc.) and thus was thought to be the result of the accumulation. The initial pH in wastewater generated from food waste was low with 3.3 and after 24 hours treatment this pH was increased to 5.8. The concentrations of COD, BOD, SS, salinity, TN and TP were gradually decreased. Food waste decay was proceeded by the seven species microorganisms identified and confirmed in this study, making a slurry phase and thus reducing residual food wastes. In the initial phase, the microbial population was approximately $3.3{\times}10^4$ cell/mL, and after 15 days this population was a constant with $5.1{\times}10^6$ cell/mL which means a certain stabilization for the reduction of food wastes. From these results, it can be considered that organic matter decomposition as well as the weight loss of food wastes by microorganisms is done at the same time.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.4
• /
• pp.1178-1185
• /
• 2010

Recently, high speed of container freight cars is causing fatigue damage of wheel. Sudden failure accidents cause a lot of physical and human damages. Therefore, damage analysis for wheel prevents failure accident of container freight car. Wheel receives mechanical and thermal loads at the same time while rolling stocks are run. The mechanical loads applied to wheel are classified by the horizontal load from contact of wheel and rail in curve line section and by the vertical force from rolling stocks weight. Also, braking and deceleration of rolling stocks cause repeated thermal load by wheel tread braking. Specially, braking of rolling stocks is frictional braking method that brake shoe is contacted in wheel tread by high breaking pressure. Frictional heat energy occurs on the contact surface between wheel tread and brake shoe. This braking converts kinetic energy of rolling stocks into heat energy by friction. This raises temperature rapidly and generates thermal loads in wheel and brake shoe. There mechanical and thermal loads generate crack and residual stress in wheel. Wetenkamp estimated temperature distribution of brake shoe experimentally. Donzella proposed fatigue life using thermal stress and residual stress. However, the load applied to wheel in aforementioned most researches considered thermal load and mechanical vertical load. Exact horizontal load is not considered as the load applied to wheel. Therefore, above-mentioned loading methods could not be applied to estimate actual stress applied to wheel. Therefore, this study proposed safety estimation on wheel of freight car using heat-structural coupled analysis on the basis of loading condition and stress intensity factor.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.6
• /
• pp.626-634
• /
• 2005

The objectives of this study was to assess pollution level and contamination status on tailings and soil in the vicinity of four disused metal mines in Kangwon province. As the result of total metal concentrations analysis, the pollution degree of tailings and soil decreased in the order of Wondong > Second Yeonhwa > Sinyemi ${\fallingdotseq}$ Sangdong mines. Total metal concentrations of mine tailings in this study were $1.2{\sim}78.2$ and $1.1{\sim}80.6$ times higher than those in the background soil and the tolerable levels suggested by Kloke, respectively. From these results, we found that tailings served as contamination source of nearby soil. According to sequential extraction of metals, large proportion of heavy metals in all mine tailings existed in the form of a residual fraction, and heavy metals in non-residual form was mainly associated with Fe-Mn oxide fraction and sulfidic-organic fraction. Fe-Mn oxide fraction and sulfidic-organic fraction of heavy metals may be released into and contaminated the nearby environment under the oxidation or reduction condition in long-term. In particular, the proportions of the exchangeable and carbonate fraction of Cd in mine tailings from Second Yeonhwa mine were relatively high. This suggests that Cd may be easily released into and contaminated the nearby environment in the near time. Concentrations of heavy metals in mine tailings and the nearby soil exceeded the standard (agricultural area) of Soil Environment Conservation Law. So it was thought that remediation for mine tailings and the nearby soil is needed. The pollution indices of the samples in this study were for higher than 1.0 and the pollution degree was very serious. Priority remediation site for these mines was Wondong. As Results of danger indices, it was showed that exchangeable form in Wondong and Fe-Mn oxide form in the rest mines should be removed preferentially.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.6
• /
• pp.663-669
• /
• 2005

The aim of this study was to investigate the ozone decay pattern for the effective application of ozone in drinking water treatment. In order to measure the ozone decomposition in water, ozone measuring instrument was developed with flow injection analysis (FIA) method. From the result of continuous residual ozone concentration in water, it was confirmed that the ozone decay pattern was divided with instantaneous ozone demand(I.D) and pseudo first-order rate($k_c$) phases, which were influenced by the variation of ozone dose. The empirical model obtained from I.D and $k_c$ values enabled us to predict the residual ozone concentration according to the reaction time, showing the high correlation between model and experimental values. The concentration of OH radical and $R__{ct}$ could be indirectly measured by OH radical probe compound. In both I.D and $k_c$ phases, the production pattern of OH radical could be observed, which was also affected by the variation of ozone dose. Finally, it was confirmed that the ozone consumption rate was varied according to the each drinking water treatment process and seasoning. Therefore, the optimum position and dosage of ozone have to be selected by considering various factors.

• Journal of radiological science and technology
• /
• v.32 no.1
• /
• pp.1-15
• /
• 2009

Newly published IEC 60601-1-3 ; 2008 2nd Edition has two important meanings. First, Radiation Quality and Dose should make sure for safety of patient and staff in manufacturing diagnostic X-ray equipment. Second, it should be minimized of Leakage Radiation, Residual Radiation, and Stray Radiation. The requirement to make enactment or revision of national standard for diagnostic X-ray Equipment is as follows : 1. It should be adjusted the new standard to the recent IEC Publication under the consideration of the Korea medical circumstances. 2. For focus to the Radiation Safety, IEC 60601-1-3 (General requirements for radiation protection in diagnostic X-ray equipment) could be applied to the new regulation. It should be compact sentence. 3. A sudden Notification change should not be desired. It needs a enough time to make easy the circumstances.

• Journal of the Korean Chemical Society
• /
• v.19 no.4
• /
• pp.269-279
• /
• 1975

Photosensitive properties of naphthoquinone-1,2-diazide-5-sulfonyl esters (PGND, BEND and PVAND) of polyglyceryl phthalate(PG), bisphenol A-epichlorohydrin condensate(BE) and polyvinyl alcohol(PVA) were investigated by the change of solubility before and after exposing to light. Various samples coated on glass or quartz plates were exposed to light under various conditions and steeped in aqueous alkali solution, and then the yield of residual film(W/W0) was determined. The yield of residual film, which was closely related to the sensitivity of the film, was affected by the degree of polymerization of the backbone resin, sensitizers and their concentration. In polymer homologs, the sensitivity was dependent on the degree of polymerization(the higher, the better). And also, it was most effective when 5 % of sensitizers to esters was used. The minimum exposed time was 0.6 min. for PGND-1, 1.0 min. for BEND-1, and 3.0 min. for PVAND-1. Most effective sensitizers for PGND, BEND and PVAND among those used here were benzanthrone, 5-nitroacenaphthene and picramide, respectively. The spectral sensitivities of PGND, BEND and PVAND were examined by comparing their spectrograms with UV-spectra in a solid state. Also, the sensitization and spectral sensitivity of the above polymers were studied. All the polymers containing the sensitizers showed optical sensitization. From the fact that in either case of sensitized or unsensitized sample, the ranges of absorption-maximum wave length were almost consistent with sensitivity maximum wave length, it was proved that the light absorbed by a sample served efficiently for photochemical reactions. Benzanthrone was found to be an excellent sensitizer for PGND.

• Journal of Periodontal and Implant Science
• /
• v.25 no.3
• /
• pp.703-719
• /
• 1995

The purpose of this study was to observe the effects of the periodontal ligament on the healing and the formation of alveolar bone in the extraction socket, when this ligament had artificially remained in the socket during the tooth removal. Twenty rats aged 4 weeks were used and devided into the control groups (10) and the experimental groups (10) in this study. The maxillary right and left first molars were extracted in both groups. In the experimental groups the periodontal ligament was remained in the extraction sockets using 0.4% ${\beta}-aminopropionitrile$, and in the control the periodontal ligament was completely removed by curettage. At 1, 3, 5, 7 and 14 days after the tooth extraction, rats in both groups were serially sacrificed. And the specimens were prepared with Hematoxylin-Eosin stain for the light microscopic evaluation. The results of this study were as follows ; 1. On 1 day, the periodontal ligament was only found in the extraction socket walls of the experimental groups, and there was not the distinguishable difference between the control and the experimental groups. 2. On 3 days, there were more collagen fibers and the appearance of higher cellular density in the experimental groups than in the control. And the cells and collagen of the periodontal ligament were so actively proliferated and synthesized that invaded into the connective tissue of the extraction sockets in the experimental groups. 3. In the experimental groups, the trabecular bone was formed on the basal and lateral bone surface on 5 days. However, there was not the new bone forming appearance in the control groups at this time. 4. On 7 days, the trabecular bone was formed in the control groups. 5. On 14 days, the extraction sockets were almost entirely filled with the bony trabeculae in both groups. But, compared to the control group, the experimental groups showed the prominent differences in the amount & the density of the new bone formed. In conclusion, it was suggested that the residual periodontal ligament tissue in the extraction socket will play a major role as the important cell source in the healing and the new bone formation of the extraction socket.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2017.06a
• /
• pp.268-268
• /
• 2017

Common sowing method of italian ryegrass (IRG) has been using the backpack seed sprayer (BSS) in Korea. It has weak point including a hard work and a little sowing area. This study was conducted to find out the effects of sowing IRG using unmanned helicopter (UH) under the established rice field. We checked the labour saving of sowing IRG and the growth and yield of rice after using IRG as forage crop. Two sowing implements(using by UH and backpack seed sprayer (BSS)) were tested for the ability of sowing IRG. For proper pretreatment of IRG seeds for aerial sowing using with UH, we tested one-day soaking seeds, iron-coated seeds, coated seeds sold in stores and untreated seeds. Aerial sowing of IRG seeds using UH was tested under the speed 10 km/h and flying altitude 3~4m. We tried to confirm the effects on rice growth in a paddy field after IRG had been used as forage in mid May. In 6 hours of seeding per day, UH had a seeding area of 21.8 hectares, three times wider than BSS. UH had a decrease of about 63 percent of sowing-seed cost in comparison with BSS. In the IRG aerial sowing using UH, coating seeds had the wider sowing width of 5~6 meter than 3~4 meter untreated seeds. Residual dry matter of IRG after using forage had 4.5 ton per hectare and 20 percent of top dry matter. The amount of nitrogen remaining in residual IRG in the soil was 12 kg per hectare, and the other nutrients such as calcium and potassium was incorporated into the soil with less than 10 kg/ha. The rice yield after the harvesting IRG was 5 percent higher than that of rice single cropping. Consequently, IRG sowing using UH was effective in reducing sowing time and sowing cost compared with conventional methods and, it is considered that there is a positive effect on the rice cultivation compared to rice single cropping.

• International Journal of Highway Engineering
• /
• v.6 no.3 s.21
• /
• pp.9-15
• /
• 2004

The cracking resistance of asphalt mixtures is generally evaluated by measuring a single parameter (i.e., Tensile strength, Stiffness). However, the use of a single parameter has been questioned in the evaluation of asphalt mixture cracking performance. The focus of this study was to clearly identify the key properties and characteristics associated with the cracking resistance of asphalt mixtures. Results of fracture, creep, and strength tests at multiple loading rates performed on the modified and unmodified mixtures showed that the mixture cracking resistance was primarily affected by the rate of micro-damage accumulation. This was reflected in the m-value, without affecting the fracture energy limit. It was also observed that the short loading time (elastic) stiffness alone could not differentiate the mixture cracking resistance of the mixtures. It was concluded that the key to characterize the cracking resistance of asphalt mixture is in the evaluation of the combined effects of creep and failure limits. It was also found that a residual dissipated energy parameter measured from Superpave IDT strength test gave the quick and useful way to distinguish the difference of cracking resistance of asphalt mixtures. Failure strain in the longer-term creep test appeared to be a useful parameter for evaluating the combined effects of creep and failure limits of asphalt mixtures.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.2
• /
• pp.165-172
• /
• 2013

Power generating unit structures are designed and built to meet standard to secure its safety for expected life time. As the structures have been exposed to combined environment, degradation of structure material is accelerated and it can cause unexpected damage; evaluating precise mechanical properties of weak site like welded area is an essential research area as it is directly connected to safety issues. Existing measuring technique like tensile test requires specific size in testing specimen yet it is destructive method which is hard to apply on running structures. To overcome above mentioned limitation, IIT is getting limelight as it is non-destructive and simple method. In this study, latest technique is introduced to evaluate tensile property and residual stress by analyzing stress field occurs under the indenter while IIT is performed. Test on welded area, the weak site of nuclear structures have been practiced and confirmed that IIT can be usefully applied to evaluate integrity in industry.