• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.8
• /
• pp.541-550
• /
• 2022

An effective real time fault diagnosis approach for UAV engine is drawn from IMM filter and GLRT methods. For this purpose based on the linear diagnosis model derived from engine dynamic performance analysis the Kalman filter for residual estimation and each method are applied to the fault diagosis of the actuator for engine control sensors. From the process of the IMM filter application the effective FDI measure is obtained and the state responses due to actuator fault are estimated. Likewise from the GLRT method the fault magnitudes of actuator and sensors are estimated associated with some FDI functionings. The numerical simulations verify the effectiveness of the IMM filter for FDI and the GLRT in estimating the fault magnitudes of each fault mode.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.12
• /
• pp.129-135
• /
• 2021

Injection molding is a manufacturing method of melting the polymer resin and injecting it into a mold to molding it into the desired form. Due to the short molding time and outstanding formability, complex products can be shaped with high precision and it is the most widely used polymer molding method. However, there may be areas that are not filled depending on the location of the injection gate where polymer resin is injected. Formability is determined by deformation and surface precision due to the impact of residual stress after molding. Hence, choosing the location of the injection gate is very important and molding analysis of injection molding is essential to reduce the cost of the mold. This study evaluated the injection formability based on the location of the injection gate of the vertical machining center ATC tool port using injection molding analysis and the results were compared and analyzed. Injection molding analysis was conducted on filling, packing, and deformation according to the location of the gate of the ATC tool port. From each injection gate location, filling time, pressure, and maximum deformation were compared. At gate 2, conditions of molding time and the location of the gate were far superior in production and quality. Gate 2 produced the smallest deformation of 0.779mm with the best quality.

• Progress in Superconductivity
• /
• v.4 no.1
• /
• pp.94-98
• /
• 2002

Two kinds of multifilament Bi-2223／Ag tapes, which are different in the precursor calcination temperatures, were heat treated for different time (12, 20, 30, 50, 70, or 100 h) firstly to obtain varied B2223 contents, and then followed by the same pressing and sintering cycles. The relation of the 2223 phase contents after the first sintering and the transport property of the fully processed tapes was studied. The results show that 75-80% 2223 phase formed in tapes before the first cold pressing is beneficial to get a high $I_{c}$ in the final tapes. Compensating the total heat treatment time of the tapes first sintered for 20 h to the same length as that first sintered for 50 h in the subsequent sintering stages, different $I_{c}$ enhancements were observed in these two tapes. No improvement on $I_{c}$ was found in the tape made from the powder calcined at higher temperature, whereas for the tape prepared with the lower temperature calcined powder, the $I_{c}$ was increased to the same level as that first sintered for 50 h. The 2223 contents before the intermediate mechanical work is related to the residual reactants, especially to the liquid phase, which is of vital importance to the phase conversion and healing microcracks, meanwhile, to the size and distribution of the non-superconducting secondary phases. The lower temperature calcined powder resulted in slow formation of 2223 phase, but also provided more reactants and liquid phase for the further phase conversion, as a consequence, for the Improvement of $I_{c}$. c/.

• Korean Journal of Veterinary Research
• /
• v.63 no.3
• /
• pp.23.1-23.9
• /
• 2023

This study was conducted to investigate tiamulin (TML) residues in the edible tissues of orally dosed broiler chickens and to re-establish the withdrawal time (WT). Thirty-six healthy Ross broiler chickens were administered 0.5 (TML-1) and 2.5 kg (TML-2) per ton feed, respectively, of the drug containing TML 78 g/kg for 10 days. Twenty-four tissue samples were collected from 6 chickens in each of the TML-1 and TML-2 groups on 0, 1, 3, and 5 days after drug administration, respectively. The residual concentrations of TML were measured using liquid chromatography-tandem mass spectrometry (LC-MS/MS). The correlation coefficient of the calibration curves was 0.9978 to 0.9998, and the limits of detection and the limits of quantification (LOQ) were in the range of 0.03 to 0.06, and 0.1 to 0.2 ㎍/kg, respectively. Recoveries ranged between 89.0% to 116.7%, and the coefficients of variation were less than 13.9%. After the drug administration, TML in the TML-1 and TML-2 groups was detected above the LOQ in 1 and 6 samples of liver, respectively, at day 0, and in 1 liver sample from both groups on day one. At 3 days after administration, TML was detected below the LOQ in all samples of TML-1 and TML-2. The calculated WT of TML in both TML-1 and TML-2 using the WT calculation program WT 1.4 was 0 days. In conclusion, the developed analytical method is suitable for detection, and the calculated WT of TML in poultry edible tissues is shorter than the current recommended WT of 7 days for TML in broiler chickens.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.18 no.1
• /
• pp.98-103
• /
• 2014

Purpose: The effective half life of I-131 is useful to calculate radiation dose, period of hospitalization, and exposure dose of surrounding people from patient. However, it is difficult to measure. This study estimates the effective half life in whole body and thyroid in using of value of residual radioactivity obtained from the early and delay images of Dual time I-131 whole body scan. Also, the correlations between the effective half life and serum creatinine, GFR, and administration dose were investigated in this study. Materials and Methods: The targets were 50 patients administration high dose of I-131 from February to August in 2013, having normal range of serum creatinine and over $30{\mu}IU/mL$ of TSH levels. After administration radioactive I-131, the early scan in the 3rd day and the delay scan in the 5-6th days were performed. To measure the residual radioactivity in the whole body and thyroid, ROI was set and then background radioactivity was corrected to estimate. The effective half life was estimated by calculating the ratio of measured values between the early and delay images. To compare the effective half lives of the whole body and thyroid, it was analyzed by Independent t-test, and each correlation of the effective half life, GFR, serum creatinine, and the dose of administration were analyzed by calculating the pearson's correlation coefficient. All of the analysis were determined to be statistically significant when P<0.05. Results: The effective half life of the whole body was $17.06{\pm}5.50$ hours and of the thyroid was $17.22{\pm}5.41$ hours. The two effective half life did not show significant difference (P=0.887). As the value of GFR was increased, the effective half life of whole body (r=-0.407, P=0.003) and of thyroid (r=-0.473, P=0.001) were significantly decreased; as the value of serum creatinine was increased, the effective half life of whole body (r=0.309, P=0.029) and of thyroid (r=0.371, P=0.008) were significantly increased. In the administration dose, effective half life did not have correlations. Conclusion: The effective half life of I-131 of patients treated for their thyroids were estimated only by using the images of Dual time I-131 whole body scan. Also, the correlations with the effective life, GFR, and serum creatinine were examined. This study might be utilized for a study on optimization for the period of hospitalization of patients treated by high dose of I-131 and on evaluation for internal absorbed dose of MIRD schema in application of the effective half life.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.13 no.3
• /
• pp.48-55
• /
• 2009

Purpose: As Korean nuclear law doesn't have any clear guideline about the dose and the external dose rate(uSv/h) requiring hospitalization in radioactive iodine treated patients, the patients are discharged when they meet the guideline of IAEA Basic Safety Standards(BSS). We measured external dose rate(${\mu}Sv/h$) of inpatient underwent 3700MBq (100 mCi) $^{131}I$ radioiodine treatment and considering external dose rate(${\mu}Sv/h$), residual activity(mCi) and excretion rate(%) we found the time for RA to be lowered from 3700MBq (100 mCi) to 1110 MBq (30 mCi) to give reference to set a guideline for discharge. Materials and Methods: Forty-two patients underwent thyroidectomy and scheduled for radioiodine treatment, who received 3700MBq (100 mCi) of $^{131}I$ orally and had no renal disease were examined. After 1, 2, 4, 8, and 20, 24, 40 hours iodine uptake and before/after the urination, the external dose rate(${\mu}Sv/h$) measured using FH40G-L(Thermo Fisher Scientific Inc., MA) at a distance and a height of 1 m for 20 sec on the average. Results and Conclusions: At 20 hours, the external dose rate was decreased to $49{\pm}13\;{\mu}Sv$/h, namely, 78% of administrated radioactivity was excreted and 814 MBq (30 mCi) was residual, and it met the accepted limit for discharge of (IAEA, BSS) under 1110 MBq (30 mCi) (1 m at 66 uSv/h).

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.26 no.6
• /
• pp.644-651
• /
• 2000

In cases of severe alveolar bony resorption in the edentulous posterior maxillae, implant placement is limited anatomically due to maxillary sinus. If the ridge is atrophic, the various bone grafting methods are required for the ridge augmentation. But the result of the onlay grafting procedure is not always promising. On the posterior maxilla, maxillary sinus mucosa lifting and bone grafting into the sinus floor, subantral augmentation(SA) technique are recommended. Various SA procedures have been developed for implant installation. We perfer to simultaneous block bone graft and implant installation through the residual alveolar ridge into the grafted block bone to fix the grafted bone and to gain the primary stability of the installed fixture. When a sagittal skeletal discrepancy in present due to the severe alveolar bony resorption of the maxilla, the advancement of the maxilla by Le Fort I osteotomy simultaneously with installation of implant fixtures combined with sinus lifting and interpositional bone graft procedure can be indicated. We applied various SA techniques for implant installtion to the 46 edentulous posterior maxillae, and total 154 implants were installed at our department from 1992 to 1999. Various SA techniques were classified in detail and the indications of each techniques were discussed. The changes of residual bony height following SA procedure were studied. The results were as follows. 1. The SA procedure combined with bone graft and simultaneous fixture installation were performed in 41 cases, 126 fixtures were installed and 5 fixtures were removed out of them. Le Fort I osteotomy procedure combined with sinus lifting and interpositional bone graft simultaneous with fixture installation were performed in 5 cases. Total 28 fixtures were installed and 2 fixtures were removed so far. 2. Autogenous block bone graft into sinus floor were performed in 35 cases, autogenous particulated marrow cancellous bone(PMCB) graft in 9 cases, and demineralized human bone powder in 2 cases. The donor site for bone graft were anterior iliac bone in 39 cases, posterior iliac bone in 3 cases and mandibular symphysis in 1 case and mandibular ramus in 1 case. 3. In 9 cases with which SA procedure had been performed with the block bone graft, the change of pre- and postoperative residual bony height were measured using MPR(multiplanar reformatted)-CT. The mean residual bony height was 8.0mm preoperatively, 20.2mm at 6 months following up operation and we gained average 12.2mm alveolar bony height. So, we can recommend this one-stage subantral augmentation and fixture installation technique as a time conserving, safe and useful method for compromised posterior edentulous maxilla.

• Korean Journal of Food Science and Technology
• /
• v.21 no.6
• /
• pp.788-794
• /
• 1989

This study was attempted to investigate the effects of blanching temperature and cooking methods on the changes in the proportions of vitamin C of fresh potato and potatoes with different storage time. Sensory evaluation of fresh potato by different cooking methods was also conducted. The contents of residual ascorbic acid(AA) and total ascorbic acid(TAA) of fresh potato were maximum at $40^{\circ}C$ followed by rapid decrease at $50-65^{\circ}C$ while leached AA and TAA showed steady increase as the blanching temperature increased. Oxidized AA and dehydroascorbic acid(DHA) hydrolyzed increased at $50-65^{\circ}C$. From these results, it was considered that AA was lost mainly by oxidation up to $65^{\circ}C$ and leaching of AA was the major mode of loss above $65^{\circ}C$. In the case of potatoes stored for 1-4 weeks, they showed similar changes in the proportions of vitamin C as that of fresh potato. However, at $40^{\circ}C$ the content of residual TAA decreased and those of leached TAA and DHA hydrolyzed increased redundant during storage. At $65^{\circ}C$, the content of DHA hydrolyzed decreased The residual TAA of fresh potato by different cooking methods decreased in the order of pressure cooking (PC) > microwave cooking (MC)>boiling. Leached TAA were 49.5% and 36.4%, during boiling and MC, respectively. While DHA hydrolyzed were 22.3% and 4.2%, respectively Leached TAA and DHA hydrolyzed during PC were not determined. From these results, it was considered that AA was lost mainly by leaching during cooking. Residual TAA of stored potatoes by different cooking methods decreased during storage. But leached TAA and DHA hydrolyzed did not show any steady increase or decrease. Overall eating quality of fresh potato by different cooking methods decreased in the order of PC>MC>boiling(p<0.05).

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.10
• /
• pp.916-927
• /
• 2010

In general water treatment process, the disinfection process by chlorine is used to prevent water borne disease and microbial regrowth in water distribution system. Because chlorines were reacted with organic matter, carcinogens such as disinfection by-products (DBPs) were produced in drinking water. Therefore, a suitable injection of chlorine is need to decrease DBPs. Rechlorination in water pipelines or reservoirs are recently increased to secure the residual chlorine in the end of water pipelines. EPANET 2.0 developed by the U.S. Environmental Protection Agency (EPA) is used to compute the optimal chlorine injection in water treatment plant and to predict the dosage of rechlorination into water distribution system. The bulk decay constant ($k_{bulk}$) was drawn by bottle test and the wall decay constant ($k_{wall}$) was derived from using systermatic analysis method for water quality modeling in target region. In order to predict water quality based on hydraulic analysis model, residual chlorine concentration was forecasted in water distribution system. The formation of DBPs such as trihalomethanes (THMs) was verified with chlorine dosage in lab-scale test. The bulk decay constant ($k_{bulk}$) was rapidly decreased with increasing temperature in the early time. In the case of 25 degrees celsius, the bulk decay constant ($k_{bulk}$) decreased over half after 25 hours later. In this study, there were able to calculate about optimal rechlorine dosage and select on profitable sites in the network map.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.4
• /
• pp.101-114
• /
• 2008

Pressurized grouting is a common technique in geotechnical engineering applications to increase the stiffness and strength of the ground mass and to fill boreholes or void space in a tunnel lining and so on. Recently, the pressurized grouting has been applied to a soil-nailing system which is widely used to improve slope stability. Because interaction between pressurized grouting paste and adjacent ground mass is complicated and difficult to analyze, the soil-nailing design has been empirically performed in most geotechnical applications. The purpose of this study is to analyze the ground behavior induced by pressurized grouting paste with the aid of laboratory model tests. The laboratory tests are carried out for four kinds of granitic residual soils. When injecting pressure is applied to grout, the pressure measured in the adjacent ground initially increases for a while, which behaves in the way of the membrane model. With the lapse of time, the pressure in the adjacent ground decreases down to a value of residual stress because a portion of water in the grouting paste seeps into the adjacent ground. The seepage can be indicated by the fact that the ratio of water/cement in the grouting paste has decreased from a initial value of 50% to around 30% during the test. The reduction of the W/C ratio should cause to harden the grouting paste and increase the stiffness of it, which restricts the rebound of out-moved ground into the original position, and thus increase the in-situ stress by approximately 20% of the injecting pressures. The measured radial deformation of the ground under pressure is in good agreement with the expansion of a cylindrical cavity estimated by the cavity expansion theory. In-situ test revealed that the pullout resistance of a soil nailing with pressurized grouting is about 36% larger than that with regular grouting, caused by grout radius increase, residual stress effect, and/or roughness increase.