• Applied Science and Convergence Technology
• /
• v.23 no.2
• /
• pp.83-89
• /
• 2014

Adsorption of residual gas molecules damped the emission current of a W (310) field electron emission (FE) emitter. The damping speed was linearly proportional to the pressure gauge readings at pressure ranging from ${\sim}10^{-8}Pa$ to ${\sim}10^{-9}Pa$, and the proportionality constant was employed to measure pressure in the $10^{-10}Pa$ range. A time plot of FE current revealed the existence of an "initial stable region" after the flash heating of W(310) FE, during which the FE current damps very slowly. The presence of non-hydrogen gas removed this region from the plot, supplying a means of qualitatively analysing the gas species.

• KCI Concrete Journal
• /
• v.12 no.1
• /
• pp.69-77
• /
• 2000

The reinforced concrete(RC) flexural members strengthened with steel plate/CFS at soffit have initial stresses and strains in reinforcements and concrete caused by the service loads at the time of retrofitting works. These initial residual stresses and strains of strengthened beams may affect the flexural performance of the rehabilitated beams. The objective of this study is to evaluate and verify the effectiveness of rehabilitation by external bonded steel plates and CFS to the tension face of the beams under three conditions of pre-loading. Thirteen beam specimens are tested and analyzed. Main test parameters are pre-loading conditions, strengthening materials and reinforcement ratio of specimens. The effect of test parameters on the strengthened beams is analyzed from the maximum load capacity, load-deflection relationship, state of stress of the materials. crack propagation phase, and failure modes. Both test results and design formulas of ACI Code provisions are compared and evaluated.

• 유체기계공업학회:학술대회논문집
• /
• 1999.12a
• /
• pp.27-32
• /
• 1999

A numerical study based on the three-dimensional thin-layer Navier-Stokes solver is carried out to analyze the flowfield through a single stage transonic compressor. Explicit four-step Runge-Kutta scheme with spatially variable time step and implicit residual smoothing is used. The governing equations are discretized with exploit finite difference method. Mixed-out average method is used at the interface between rotor and stator. And, an artificial dissipation model is used to assure the stability of solution. The results with k-$\omega$ turbulence model were compared to the results with Baldwin-Lomax model, and physical phenomena of transonic compressor are presented. The two turbulence models give the results that show reasonably good agreements with experimental data.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.16 no.2
• /
• pp.191-197
• /
• 2006

This paper deals with a fault detection system design for nuclear steam generator water level control system. We expressed the nonlinear properties of the steam generator level system as a T-S fuzzy system with time varying uncertain parameters. We design a residual generator using a left coprime factorization of the T-S fuzzy model and a fault detection filter in order to improve the fault detection performance. We demonstrate the efficiency of the suggested design method via many computer simulations.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.3
• /
• pp.312-320
• /
• 1990

Analysis and lattice implementation of Extended Instrumental Variable (EIV) methods for high resolution spectral analysis are presented. The performance of EIV is improved by using prefilters and the unbiasness of EIV is proved by using the fact that residual processes are white. We derive the order and time update formulas for the covariance lattice algorithm which is particularly useful in case of short data or nonstationary processes. The ARMA model can be modeled as two channel AR processes. Using this model, the lattice algorithms of EIV are derived. Computer simulations are performed to show the usefulness of the proposed algorithms.

• Journal of the Korean Ceramic Society
• /
• v.35 no.8
• /
• pp.850-856
• /
• 1998

The dynaamic fatigue behavior of alumina ceramics was observed at room temperature using four-point bending method. Dynamic fatigue fracture strength was observed as function of down speed and notch length. The crack growth exponent of the specimens was calculated from the fracture strength and lifetime in dynamic fatigue test. After loading the stresses in the range of 0% to 105% compared with the average in-ert strength the value of residual fracture strength was measured for unnotched and 0.5mm notched speci-mens at the 0.001 and 0.0005 mm/min down speed respectively. After the 95% stress of the average inert strength was applied repeatedly the value of rsidual fracture strength was measured for 0.5mm notched specimens at the 0.001 and 0.0005 mm/min down speed respectively. The material constant A was found to be almost the same and not to depend on the loading mode or the down speed for unnotched and notched specimen. The value of fracture strength with time calculated from the constants n and A was in good agreement with the measured value.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.250-252
• /
• 2007

In this paper presents a control algorism for myoelectric hand prosthesis(MHP) with 2 degree of freedom(DOF), which consists of a mechanical hand, a surface myoelectric sensor(SMES) for measuring myoelectric signal, a control system and a charging battery. The actuation for the 2-DOF hand functions such as grasping and wrist rotation was performed by two DC-motors, and controlled by myoelectric signal measured from the residual forearm muscle. The two controllers were made of a RISC-type microprocessor, and its software was executed on a real-time kernel. The experimental results were showed that the proposed a control algorism is feasible for the MHP.

• Proceedings of the KIEE Conference
• /
• 1996.07b
• /
• pp.1301-1303
• /
• 1996

A new automatic frequency control(AFC) tracking algorithm, which we call a rotational decision directed AFC(RDDAFC) is proposed for QPSK demodulation at the digital direct broadcasting satellite(DBS). In order to prevent the presence of the residual phase difference between symbols received at k and k-l by the CPAFC[1] as well as the AFC based on $tan^{-1}$ circuit[2], the RDDAFC rotates the decision boundary for the kth received symbol by the frequency detector output of the (k-1)th received symbol before passing through the cross product discriminator. Test results show that the total pull-in time of the RDDAFC and PLL was 0.13msec under a carrier frequency offset of 2.4MHz when S/N equals 2dB.

• Textile Coloration and Finishing
• /
• v.4 no.4
• /
• pp.90-96
• /
• 1992

In the PAN-based ACF manufacturing system stabilization step was improved with chemical treatment (preoxidation) in order to yield higher carbon content and to avoid excessive fragmentation during carbonization and activation process. The optimal condition of preoxidation was at 18$0^{\circ}C$ for 4 minutes in sodium glyceroxide in glycerine (concentration of NaOH was 0.02 meq/g). To investigate low temperature stabilization effect, preoxidized PAN fiber heated 22$0^{\circ}C$ to 26$0^{\circ}C$ as a function of treatment time and oxidative gas atmosphere, and analysed by infrared spectrum and TGA. As a results of IR and TGA, it was clear that impregnated[preoxidative] PAN had 14% higher residual than untreated PAN at 100$0^{\circ}C$ and the optimal condition of stabilization was at 26$0^{\circ}C$ for 3.5 hours within $N_2$ atmosphere.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.2
• /
• pp.81-91
• /
• 2000

Dynamic models of line regulator valve(LRV) and ratio control valve (RCV) are obtained for an electronic controlled CVT. LRV and RCV are operated by variable force solenoid(VFS). Considering the CVT shift dynamics, oil pump's efficiency and saturation characteristics of VFS, simulations are performed and compared with test results. Simulation results are in good agreement with the experiments, which shows the validity of the dynamic models of LRV and RCV obtained. In addition, the effects of the orifice size in the exhaust port of RCV are investigated. Simulation results show that as the orifice size decreases, the residual pressure in the primary actuator increases which insures the large torque transmission capacity, meanwhile the duration time for the downshift increases.