• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.8
• /
• pp.1062-1068
• /
• 2000

The effect of heat exchanger surface treatment on the frosting/defrosting behavior in a fin-tube heat exchanger is investigated experimentally. It is found that the hydrophilic surface mainly influences on the frosting behavior, however, the hydrophobic surface gives some influence on the defrosting behavior. In view of frosting performance, surface-treated heat exchanger with either hydrophilic or hydrophobic characteristic shows a little improvement in the thermal performance than the aluminium heat exchanger with no surface treatment. The result reveals that the heat exchanger with hydrophobic surface treatment is more effective in view of the defrosting efficiency and time. The amounts of residual water on the surface-treated heat exchangers are shown to be smaller than those of the bare heat exchanger, therefore further improvements on the performance of re-operations are expected.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.275-280
• /
• 2008

To improve the durability of a hydrogen pressure vessel which is applied high-pressure, it needs the autofrettage process which induces compressive residual stress in the Aluminum liner. This study presents the elasto-plastic analysis to predict the behavior of structure accurately, and the Tsai-Wu failure criterion is applied to predict failure of pressure vessel of Aluminum liner and composite materials. Generally, plastic analysis is more complex than elastic analysis and has much time to predict. To complement its weakness, the AxicomPro(EXCEL program), applied radial return algorithm and nonlinear classical laminate theory (CLT), is developed for predicting results with more simple and accurate than the existing finite element analysis programs.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1995.06a
• /
• pp.146-149
• /
• 1995

This paper proposes a SM-CELP speech coder which applies different excitation signal according to the characteristic of speech segment at bit-rate below 4 kbps. Speech signal is divided with 2 modes such as stationary voice and etc. using the parameters of average energy of the short-time speech and the residual signal after long term prediction. Structured multi-pulse method is used for the excitation of mode-A and gaussian or pulse-like codebook for mode-B. 4.8kbps DoD-CELP are used to evaluate the performance of the proposed coder. As a result, the propose method shows 1~2 dB higher segmental signal to noise ratio and better subjectional quality without increasing the computational amount.

• Journal of the Korean Mathematical Society
• /
• v.55 no.6
• /
• pp.1529-1540
• /
• 2018

The matrix equation $X^p+A^*XA=Q$ has been studied to find the positive definite solution in several researches. In this paper, we consider fixed-point iteration and Newton's method for finding the matrix p-th root. From these two considerations, we will use the Newton-Schulz algorithm (N.S.A). We will show the residual relation and the local convergence of the fixed-point iteration. The local convergence guarantees the convergence of N.S.A. We also show numerical experiments and easily check that the N.S. algorithm reduce the CPU-time significantly.

• 한국전산유체공학회:학술대회논문집
• /
• 1998.05a
• /
• pp.181-189
• /
• 1998

A numerical study based on the three-dimensional Reynolds averaged Navier-Stokes equations is presented to analyze the transonic flowfield through two-stage axial compressor. Explicit four-step Runge-Kutta scheme is used for solution algorithm, and local time step and implicit residual averaging are introduced for enhancing the convergency. Artificial dissipation model is adopted to assure the stability of solution. The solver is coupled with Baldwin-Lomax model to describe turbulence. To avoid calculating the unsteady flow, a mixing process is modeled at a station between rotating and stationary blade rows. Results show a variety of important physical phenomena. Comparison of the flowfields with and without tip clearance shows that the effect is considerable in this flowfield. Comparisons with experimental data carried out to validate the calculational results show reasonable agreements. Some remedies are also suggested to improve the revealed problems.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.274-279
• /
• 2001

Creep-fatigue crack growth behavior was experimentally measured particularly when a crack was located in the heat affected region of 1Cr-0.5Mo steel. Load hold times of the tests for trapezoidal fatigue waveshapes were varied among 0, 30, 300 and 3,600 seconds. Time-dependent crack growth rates were characterized by the $C_t$-parameter. It was found that the crack growth rates were the highest when the crack path was located along the fine-grained heat affected zone(FGHAZ). Cracks located in other heat affected regions had a tendency to change the crack path eventually to FGHAZ. Creep-fatigue crack growth law of the studied case is suggested in terms of $(da/dt)_{avg}$ vs. $(C_t)_{avg}$ for residual life assessment.

• Journal of Surface Science and Engineering
• /
• v.40 no.1
• /
• pp.39-43
• /
• 2007

The pure CrN powders oxidized to $Cr_2O_3$ noticeably above $850^{\circ}C$ in air. When these powders were sintered into bulk samples at $1500^{\circ}C$ under 40 atm of $N_2$ pressure, the CrN phase partly changed into the $Cr_2N$ phase, owing to the partial loss of nitrogen from CrN. When the bulk sample was heated at $1000-1200^{\circ}C$ for 100 hr under vacuum, the CrN phase also progressively changed into $Cr_2N$. At the same time, a relatively thin $Cr_2O_3$ layer formed on the bulk sample due to the reaction of chromium with residual oxygen in vacuum.

• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.6
• /
• pp.739-748
• /
• 2004

A hybrid dust-collector combining a fabric filter with centrifugal force was developed to enhance the performance of the conventional fabric filter systems and its performances were evaluated to compare to that of the existing dust collector. The pressure drop rapidly increased with increasing the elapsed time and the face velocity in two filtration systems. But the increasing ratio of a hybrid dust-collector compare to the existing dust collector was lower. This results were confirmed from the performance such as cleaning interval, residual pressure drop and dust loading rate. The overall collection efficiency of the hybrid dust-collector was more than 99.6% and this showed a improvement of 0.6～2% than that of the existing dust collector. Especially, the fractional collection efficiency at the particle size of around 1${\mu}{\textrm}{m}$ is about 4% higher than that of the existing dust collector.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.28-32
• /
• 1995

This effective way for repairing a fatigue crack is making indetations around fatigue crack tip. In this paper, we performed fatigue test to investigate the optimal position of the indentations, and observed crack opening behavior at the same time. The indentation positions of specimens were on the crack tip, front and back of the crack tip. The results of the experiment showed taht it was veryeffective way to increase fatigue life that making indentations on the crack tip, and it was the optimal position that making indentations on the crack tip.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.10
• /
• pp.2667-2677
• /
• 1995

A new numerical algorithm using equal order linear finite element and fractional step method has been developed which is capable of analyzing unsteady fluid flow and heat transfer problems. Streamline Upwind Petrov-Galerkin (SUPG) method is used for the weighted residual formulation of the Navier-Stokes equations. It is shown that fractional step method, in which pressure term is splitted from the momentum equation, reduces computer memory and computing time. In addition, since pressure equation is derived without any approximation procedure unlike in the previously developed SIMPLE algorithm based FEM codes, the present numerical algorithm gives more accurate results than them. The present algorithm has been applied preferentially to the well known bench mark problems associated with steady flow and heat transfer, and proves to be more efficient and accurate.