• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2001.02a
• /
• pp.139-141
• /
• 2001

YBCO superconductors were prepared by top-seeded melt growth process using various numbers of seeds. The levitation forces and trapped magnetic fields of the top surfaces of the samples were measured using Nd-B-Fe permanent magnets It was found that the processing time was greatly reduced by multiple seeding, but the properties were decreased as the number of seeds was increased. The degradation of the properties is attributed to the presence of the nonsuperconducting phases at the grain boundaries as result of the entrapment of a residual melt at grain boundaries during melt processing.

• Journal of the Korean Ceramic Society
• /
• v.28 no.9
• /
• pp.712-720
• /
• 1991

The effect of cyclic compressive stress on fracture responses of Al2O3 was investigated under uniaxial stress cycling. Experimental data were obtained for Al2O3 tension specimens under uniaxial tension-unloading and tension-compression cyclic loading conditions. To investigate the effect of compressive stress on the crack growth, theoretical results from the crack growth rate were compared with measured stress vs. failure relations. At low stress level in tension-compression cycling, residual tensile strains were also observed about failure time.

• Journal of the Korean Ceramic Society
• /
• v.33 no.8
• /
• pp.871-876
• /
• 1996

It is believed that fly ash could be suitable for preparing the sialon by carbothermal reduction method because the total amount of SiO2 and Al2O3 is above 80% and the unburned residual carbon is above 5% within the fly ash. The effects of reaction temperature (1350, 1400, 145$0^{\circ}C$) reaction time (1, 5, 10 hours) and the amount of carbon additions (C/SiO2=2, 3, 4 mole) on the $\beta$-sialon synthesis were obserbed, It was conformed that $\beta$-sialon (Z=2.15~2.18) was formed as major phase under all of the synthesis conditions and small amount of Si2ON2 SiC, AlN and Si3N4 was formed depending on the synthesis conditions. FeSix intermetal-lic compound was formed above 140$0^{\circ}C$ reaction temperature due to the large amount of iron oxides within the raw fly ash.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.34S no.11
• /
• pp.16-24
• /
• 1997

In order to prevent the presence of the residual phase difference at the discriminator output by the existing AFC techniques, we propose a new automatic frequency control(AFC) tracking algorithm for QPSK demodulation at the digital direct broadcasting satellite(DBS) receiver, which we call a rotational decision-directed AFC(RDDAFC). The RDDAFC rotates the decision boundary for the kth received symbol by the frequency deterctor output of the (k-1)th received symbol. Tracking performances of carrier frequency offset by the proposed RDDAFC algorithm are evaluated through computer simulations under the practical DBS channel conditions with a carrier frequency offset of 2.3MHz when S/N equals 2dB. Test results show that the total pull-in time of the RDDAFC is 1.697msec for 10$^{-3}$ SER before forwared error correction at the receiver.

• The KSFM Journal of Fluid Machinery
• /
• v.3 no.3 s.8
• /
• pp.7-11
• /
• 2000

A numerical study based on the three-dimensional thin-layer Navier-Stokes solver is carried out to analyze the flowfield through a single stage transonic compressor. Explicit fout-step Runge-Kutta scheme with spatially variable time step and implicit residual smoothing is used. The governing equations we discretized with explcit finite difference method. Mired-out average method is used at the interface between rotor and stator. And, an artificial dissipation model is used to assure the stability of solution. The results with k-w turbulence model were compared to the results with Baldwin-Lomax model, and physical phenomena of transonic compressor are presented. The two turbulence models give the results that show reasonably good agreements with experimental data.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.28-33
• /
• 2006

Shallow failures of slopes in weathered soils are caused by infiltration due to prolonged rainfall. These failures are mainly triggered by the deepening of the wetting band accompanied by a decrease in suction induced by the water infiltration. In this paper, hysteresis on soil-water characteristic curve(SWCC) of granite and gneiss weathered soils are investigated using transient flow analysis respectively. Each case was subjected to artificial rainfall intensities and time duration depending on the laboratory-based drying and wetting processes. The results show that the unsaturated seepage on weathered slopes are very much affected by the initial suction of soils and unsaturated permeability of the soils. In addition, a granite weathered soil has a lower air-entry value, residual matric suction, and wetting front suction and less hysteresis loop than a gneiss weathered soil.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.1023-1030
• /
• 2005

This study is an experiment paper about the ground improvement material which using the waste residual(slag and paper fly ash) by fire. we are research to concern according to the soil to mix the ground improvement material at show strength effectiveness. Also, we can expect a long time strength increase effectiveness as reduce the dryness contraction. They are distinguished to the clay of the reclamation ground and silty sand soil. We examined around an uniaxial compress test and scanning electron microscopy. The uniaxial stress increases according to the increase of the mixed ratio of ground improvement material and the water contents have been reduced the strength value. A clay's improvement effectiveness is big but in the silty sand soil to express small effectiveness. A ground improvement material mixing of the quantity to write can not expect the effect of Ettringite.

• Proceedings of the KIEE Conference
• /
• 2001.11c
• /
• pp.42-45
• /
• 2001

In the speed-sensorless induction motor control systems, only a few percents of error in current measurement badly deteriorates the control performance. And early detection and accomodation of the faults of current sensor is very important to enhance the reliability of the induction motor control system. In this paper, we propose two sensor fault detection schemes having desired functions; fault detection, isolation of failed sensor and compensation of fault effect. The two schemes operate in real-time and employ EKFs (Extended Kalman Filter) for residual generation. Simulation results show that the proposed schemes are very useful in maintaining the control performance of the induction motor driven servo systems even in the face of sensor faults.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.575-578
• /
• 2004

In this study, we designed HAN(hybrid-aligned nematic) cell using novel tilt angle control method. It was possible to make novel HAN cell using a single polyimide by hot plate baking method. This new HAN cells showed slower response time as compared with conventional HAN cell. However, the alignment state and V-T curve of HAN cell using novel method were acceptable. Also, it showed better C-V characteristic than that of conventional HAN cell.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.487-488
• /
• 2010

This is the experimental and analysis study on the thermal distribution, structural behavior and residual strength of high strength concrete members subjected to fire. The parameters are strength of concrete, cover thickness, loading state and exposure time to fire. The ISO 834 standard fire curve is used to test. The material and structural property of concrete at high temperature are proposed, also.