• 한국기계가공학회지
• /
• 제9권1호
• /
• pp.106-113
• /
• 2010

The most suitable condition for plasma source ion implantation(PSII) was found based on the study of the characteristics of PSIIed tool and machined surfaces. The depth analysis according to the chemical bonding state of elements and surface component elements through the XPS and SIMS, was conducted to find the improved property of the PSIIed surface. Due to the diffusion of PSII, the nitrogen was found up to a depth of about 150nm according to the supplied voltage and ion implanted time. The deep diffusion by nitrogen caused the surface modification, but the formation of oxide component was found due to the residual gas contamination on the surface. Statistical method of ANOVA was conducted to find the effects of spindle speed and feed rate in interaction for machined surface roughness with PSIIed tools. The surface modification was found largely occurred by the nitrogen implanted surface with 2 hours for 27kV, 35kV and 43kV.

• 청정기술
• /
• 제14권1호
• /
• pp.14-20
• /
• 2008

본 연구에서는 LCD BLU에 적용 가능한 면광원용 저온소성 형광체 페이스트(paste)를 제조하여 그 특성을 검토하였다. 형광체 paste에는 저온 소성용 아크릴 레진을 바인더로 사용하였으며, 그 열분해특성을 검토한 결과 $400^{\circ}C$에서 잔탄이 0.1 wt% 이하인 것을 확인 할 수 있었다. 본 연구에서 제조한 paste로 스크린 인쇄를 통해 면광원용 device를 제작한 결과, 형광체 휘도에 대해 100%에 가까운 발광특성을 나타내었다.

• Journal of Microbiology and Biotechnology
• /
• 제22권9호
• /
• pp.1185-1192
• /
• 2012

This study investigated the hydrocarbonoclastic microbial community present on weathered crude oil and their ability to degrade weathered oil in seawater obtained from the Gulf St. Vincent (SA, Australia). Examination of the native seawater communities capable of utilizing hydrocarbon as the sole carbon source identified a maximum recovery of just $6.6{\times}10^1\;CFU/ml$, with these values dramatically increased in the weathered oil, reaching $4.1{\times}10^4\;CFU/ml$. The weathered oil (dominated by > $C_{30}$ fractions; $750,000{\pm}150,000mg/l$) was subject to an 8 week laboratory-based degradation microcosm study. By day 56, the natural inoculums degraded the soluble hydrocarbons (initial concentrations $3,400{\pm}700mg/l$ and $1,700{\pm}340mg/l$ for the control and seawater, respectively) to below detectable levels, and biodegradation of the residual oil reached 62% ($254,000{\pm}40,000mg/l$) and 66% ($285,000{\pm}45,000mg/l$) in the control and seawater sources, respectively. In addition, the residual oil gas chromatogram profiles changed with the presence of short and intermediate hydrocarbon chains. 16S rDNA DGGE sequence analysis revealed species affiliated with the genera Roseobacter, Alteromonas, Yeosuana aromativorans, and Pseudomonas, renowned oil-degrading organisms previously thought to be associated with the environment where the oil contaminated rather than also being present in the contaminating oil. This study highlights the importance of microbiological techniques for isolation and characterisation, coupled with molecular techniques for identification, in understanding the role and function of native oil communities.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권5호
• /
• pp.617-624
• /
• 2010

선박 건조공정에서 외피의 곡면 가공에 많이 사용하는 가공법을 선상가열법이라고 한다. 선상가열법은 엔지니어의 숙련도에 따라 품질의 차이가 커지기 때문에 현재에는 엔지니어의 숙련도에 의존하지 않는 자동화기기를 사용하여 선상가열을 수행하는 경우가 많다. 본 연구에서는 자동화기기를 사용한 선상가열에 의한 가열판재의 온도분포를 조사하고자 한다. 선상가열시 적용되는 주요한 변수는 가열원의 이동속도, 강도 및 가열 방식 등이 있으며, 본 연구에서는 세 가지 변수를 중심으로 가열판재의 표면 및 내부온도가 어떻게 변화하는지를 조사하였다. 해석결과 가열원의 이동속도가 빨라질수록 판재의 피크온도는 낮게 형성되는 것을 확인하였고, 또한 열원의 크기에 따른 피크온도 및 온도분포가 선형적으로 변화하는 것을 정량적으로 계산할 수 있었다.

• 한국정보과학회논문지:정보통신
• /
• 제31권5호
• /
• pp.519-531
• /
• 2004

무선 애드혹 통신망은 고정된 기간망 없이 이동 기기들이 모여서 형성하는 임시 무선 시스템이다. 무선 애드혹 통신망에서는 이동 기기들이 모여서 통신망을 형성하므로 개개의 이동 기기의 수명이 통신망 자체의 수명을 결정짓는 중요한 요소가 된다. 망의 구조에 따라서 어떠한 경우는 단지 하나의 이동 기기가 자신의 배터리를 모두 소모하고 동작을 멈추었을 뿐인데, 이것이 통신망의 분할(partition)을 가져올 수도 있다. 이처럼 이동 기기의 수명은 각 이동 기기가 가지고 있는 배터리에 의존하므로 될 수 있는 한 소모하는 에너지량을 줄여 모든 이동 기기들이 골고루 오래 살수 있도록 하는 것이 전체 통신망의 수명을 늘릴 수 있는 방안이 된다. 본 연구에서는 모든 이동 기기들이 오랫동안 함께 살 수 있도록 최적의 경로를 선택하여 통신을 하도록 하는 전력 인식 동적 소스 라우팅(Power-Aware Dynamic Source Routing: PADSR) 프로토콜을 제안한다. PADSR에서는 송신 기기가 패킷(packet) 전송을 위한 경로를 선택할 때 어떤 특정 이동 기기의가 에너지를 많이 소모하지 않도록 하기 위하여 경로 선택 시에 경로에 포함되어 있는 이동 기기들의 남아있는 배터리량과 패킷을 전달하는데 소모하게 되는 송신 에너지량을 고려한다. 따라서 PADSR을 사용하게 되면 통신망의 수명이 연장된다.

• 한국재료학회지
• /
• 제8권3호
• /
• pp.229-237
• /
• 1998

열적으로 이온화된 N과 증기상태의 Ga을 $300~730^{\circ}C$의 온도 범위에서 직접 반응시켜 (001)Si과 (00.1)사파이어 기판 위에 GaN박막의 성장 초기 단계에서는 GaN의 성장률이 증가한 후, 결정 핵을 중심으로 수평방향으로서 성장과 합체에 의하여 성장률의 변화가 일정 값에 달하였다. 이 연구에서 성장한 GaN박막에 대한 XPS분석 결과 낮은 온도에서 성장된 GaN박막은 진공 chamber 내의 산소가 성장된 박막 내에 많이 혼입 되어 있음을 알 수 있었다. 낮은 온도, 짧은 시간 동안 성장된 표면은 Ga덩어리들도 도포 되었다. 그러나, 기판온도와 성장시간이 증가함에 따라 이들은 피라미드 형태의 결정들로 성장된 후 원형고리 형태의 결정으로 합체되었다. 특히 N-소스의 공급이 충분한 경우에는 판상의 결정으로 성장되었다. 20K의 온도에서 측정된 PL스펙트럼에서는 3.32eV와 3.38eV에서 불순물과 관련된 발광이 관찰되었다.

• 한국세라믹학회지
• /
• 제44권7호
• /
• pp.381-386
• /
• 2007

A porous reaction bonded silicon carbide (RBSC) was fabricated by a molten Si infiltration method. The porosity and flexural strength of porous RBSC fabricated in this study were dependent upon the amount of carbon source used in the SiC/carbon preform as well as the amount of Si infiltrated into the SiC/carbon preform. The porosity and flexural strength of porous RBSC were in the range of $20 vo1.{\sim}49 vo1.%$ and $38{\sim}61 MPa$, respectively. With increase of carbon contents and molten Si for infiltration, volume fraction of the pores was gradually decreased, and flexural strength was increased. The porous RBSCs fabricated with the same amount of molten Si show less residual Si around neck with increase of carbon source, as well as a new SiC was formed around neck which resulted in the decreased porosity and improvement of the flexural strength. In addition, decrease of the porosity and increase of the flexural strength were also obtained by increase of the amount of molten Si with the same amount of carbon source. However, it was found that the flexural strength of porous RBSC depends on the porosity rather than the amount of the newly formed SiC in neck phase between SiC particles used as a starting material.

• 한국산림과학회지
• /
• 제99권5호
• /
• pp.706-710
• /
• 2010

Understanding of chemical composition and energy contents in tree is important to develope strategies of renewable energy policy to cope with climate change. Residual biomass as renewable energy source was evaluated and focused on the bark-containing branches. Chemical analysis studies were conducted for different part of yellow poplar (Liriodendron tulipifera), which were partitioned to inner bark, outer bark, small branches, medium branches, big branches and trunk. The variations in hydrophobic extractives, hydrophilic extractives, lignin, carbohydrate compositions, energy contents (higher heating value) and the ash content were determined. The inner and outer bark had higher ash content, hydrophobic and hydrophilic extractives content, and higher energy content than those of tree trunk. Polysaccharides content in inner and outer bark was quite lower than those of stem or branches. Based on the energy content of residual biomass, replacement of fossil fuel and greenhouse gas emission abatement were calculated.

• 대한기계학회논문집A
• /
• 제26권11호
• /
• pp.2415-2420
• /
• 2002

In the present study, a new anchor design was proposed to minimize the initial deflection of micro multi-layer cantilever beam with step-up structure, which is a key component of thin film micro-mirror array. It is important to minimize the initial deflection, caused by residual stress, because it reduces the performance of the actuation. Theoretical and experimental studies were conducted to examine the cause of the initial bending deflection. It was found that the bending deflection at the anchor of the cantilever beam was the primary source of initial deflection. Various anchor designs were proposed and the initial deflections for each design were calculated by finite element analysis. The analysis results were compared with experiments. To reduce the initial deflection a secondary support was added to the conventional structure. The optimal shapes were obtained by simulation and experiment. It was found from the analysis that the ratio or horizontal and vertical dimensions of secondary support was the governing factor, which affected the initial deflection.

• 한국레이저가공학회지
• /
• 제4권1호
• /
• pp.21-28
• /
• 2001

Simulation on the electron beam welding of Al 2219 alloy was carried out by using commercial FEM code MARC, which encounters moving heat sources. Due to axisymmetry of geometry, a half of the cylinder was simulated. A coupled thermo-mechanical analysis was carried out and subroutine for heat flux was substituted in the program. The material properties such as specific heat, heat transfer coefficient and thermal expansion coefficient were given as a function of temperature and the latent heat associated with a given temperature range is considered. As a result, the proper beam power is 60㎸${\times}$60㎃ and welding speed is 1∼1.5 m/min. The residual stress in the heat-affected zone as well as the fusion zone does not increase. It is necessary to use jigs for preventing distortion of cylinder and improving weld quality.