• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.8
• /
• pp.1091-1096
• /
• 2012

The aerodynamic characteristics of circular cylinder in a channel are studied to make clear the flow feature by solving the Navier-Stokes equation based on the finite volume method with unstructured grids. Reviews are made on with the vorticity, velocity, dynamic pressure, residual and drag, where the Reynolds numbers are 50 and 100. The flows for $Re{\succeq}50$ shows the vortex shedding in the wake, and the result is the same as the case of moving cylinder. The ground effect of flat bottom results in the growth of vortex, being generated in the upper side of the cylinder and elongated in the rear. As the cylinder approaches to wall, for example 0.6, the cylinder plays as a role of blockage to obstruct the flow between the cylinder and wall. The drag coefficients are compared with others' results to confirm the validity of the present numerical simulation.

• Journal of Energy Engineering
• /
• v.12 no.1
• /
• pp.1-10
• /
• 2003

Pressurized fluidized bed combustion unit is operated at pressures of 1~1.5 MPa with combustion temperatures of 850~87$0^{\circ}C$. The pressurized coal combustion system heats steam, in conventional heat transfer tubing, and produces a hot gas supplied to a gas turbine. Gas cleaning is a vital aspect of the system, as is the ability of the turbine to cope with some residual solids. The need to pressurize the feed coal, limestone and combustion air, and to depressurize the flue gases and the ash removal system introduces some significant operating complications. The proportion of power coming from the steam : gas turbines is approximately 80:20%. Pressurized fluidized bed combustion and generation by the combined cycle route involves unique control considerations, as the combustor and gas turbine have to be properly matched through the whole operating range. The gas turbines are rather special, in that the maximum gas temperature available from the FBC is limited by ash fusion characteristics. As no ash softening should take place, the maximum gas temperature is around 90$0^{\circ}C$. As a result a high pressure ratio gas turbine with compression intercooling is used. This is to offset the effects of the relatively low temperature at the turbine inlet.

• KSBB Journal
• /
• v.24 no.6
• /
• pp.556-562
• /
• 2009

The biological treatment of TNT-containing wastewater, known commonly as pink water, was investigated using a stirred tank reactor with Stenotrophomonas maltophilia OK-5 bacterial culture. S. maltophilia OK-5 exhibited effective degradation of TNT contained in pink water, completely degrading TNT (100 mg/L) within 6 days of incubation. The dark-red brown color derived from Hydride-Meisenheimer complex became more pronounced during the incubation period, which was determined quantitatively. High-pressure liquid chromatography was used to measure residual TNT, which also resolved the metabolic intermediates (i.e., 2,4-dinitrotoluene, 2,6-dinitrotoluene and 2,4-dinitro-6-hydroxytoluene). Gas chromatography-mass spectrometry was used to verify these intermediates. Quantification of the nitroreductase (pnrB) gene isolated from S. maltophilia OK-5 growing in pink water was performed with real-time PCR. The amount of pnrB gene copies increased to $10^3$-fold after 5 days of incubation time.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.5
• /
• pp.574-581
• /
• 2015

In this paper, the effect of high voltage current pulse against shaped charge jet was analyzed through the visualization of jet behavior using flash X-ray and comparison of depth of penetration(DOP) into RHA(Rolled Homogeneous Armor) witness plates. The behavior of jet particles has been acquired using a flash X-ray equipment when current pulse was applied into the metal jet of a shaped charge(SC) warhead. Typical results such as jet breakup and radial jet dispersion, which are due to electromagnetic pressure by current pulse, have been obtained. Dozens of penetration experiments using a shaped charge with 55 mm diameter were performed according to various combinations of major parametric variables such as electrode spacing, standoff distance from SC warhead to electrode, and charge voltage. Subsequently, interrelations between major parametric variables and DOPs into RHA were analyzed.

• Asian-Australasian Journal of Animal Sciences
• /
• v.15 no.3
• /
• pp.416-420
• /
• 2002

Various products of karanj (Pongamia glabra) are utilized for industrial, health and animal agriculture applications in the Indian subcontinent. Despite a rich source of protein (CP, 28-34%), karanj cake was found to be slightly bitter in taste and toxic owing to the presence of flavonoid (Karanjin), restricting its safe inclusion in the livestock diets. Feeding trials with raw cake revealed its poor palatability and adverse performance among different categories of livestock including poultry. The present study was, therefore, aimed to detoxify karanj cake by various physico-chemical methods like solvent extraction, water washing, pressure cooking and alkali and acid treatments. The level of residual karanjin in raw and variously processed cake was quantified using high performance liquid chromatography (HPLC). The raw expeller karanj cake was found to contain about 0.19% of karanjin. Though a non-polar solvent, soxhlet extraction of expeller pressed cake with petroleum ether drastically reduced karanjin content (0.01%). Soaking of cake for 24 h in 1% NaOH (w/w) solution was found to reduce karanjin to a major extent with little further benefit by increasing alkali level. Milder alkalies like lime and fertilizer grade urea reduced the karanjin levels marginally. Similar was the case with mineral acids such as HCl and glacial acetic acid. It was, therefore, concluded that solvent extraction of karanj seeds would be the best method of detoxification as well as for more recovery of oil and karanjin.

• Journal of Powder Materials
• /
• v.11 no.4
• /
• pp.308-313
• /
• 2004

An experimental study on the combustion of superfine aluminum powders (average particle diameter, a$_{s}$: ∼0.1 ${\mu}{\textrm}{m}$) in air is reported. The formation of aluminum nitride during the combustion of aluminum in air and the influence of the combustion scenario on the structures and compositions of the final products are in the focus of this study. The experiments were conducted in an air (pressure: 1 atm). Superfine aluminum powders were produced by the wire electrical explosion method. Such superfine aluminum powder is stable in air but once ignited it can burn in a self-sustaining way due to its low bulk: density (∼0.1 g/㎤) and a low thermal conductivity. During combustion, the temperature and radiation were measured and the actual burning process was recorded by a video camera. Scanning electron microscopy (SEM), X-ray diffraction (XRD) and chemical analysis were performed on the both initial powders and final products. It was found that the powders, ignited by local heating, burned in a two-stage self-propagating regime. The products of the first stage consisted of unreacted aluminum (-70 mass %) and amorphous oxides with traces of AlN. After the second stage the AlN content exceeded 50 mass % and the residual Al content decreased to ∼10 mass %. A qualitative discussion is given on the kinetic limitation for AlN oxidation due to rapid condensation and encapsulation of gaseous AlN.N.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2005.11a
• /
• pp.87-95
• /
• 2005

Laser sealing/cutting technique, one of the 4 core technologies to manufacture self-luminous glass tubes (SLGTs) has been developed. Through the analysis of commercial products it is found that Pyrex Is used for SLGTs. A CO2 laser, which is commonly used for glass work was used for the study The factors affecting the sealing/cutting were laser intensity, duration. Irradiation method, and pressure inside the tube. The whole Process is composed of 2 stages. In the first stage. both ends of the tubes are sealed while tritium is insected in the tubes. And the tritium sealed tubes are cut in the desired size in the second stage. Defocused beam was used for seal ing and focused beam was used for cutting. After the sealing/cutting, the tubes were heat treated to prevent fracture due to the residual heat stress.

• Journal of the Korean Magnetics Society
• /
• v.3 no.3
• /
• pp.229-233
• /
• 1993

The effects of differential partial pressures of oxygen during sputtering on the magnetic and recording characteristics of magneto-optical disks were investigated. Different flows of oxygen were deliberately introduced into the sputtering chamber to have a variety of partial pressures of oxygen during sputtering. A residual gas analyzer was employed to monitor the oxygen peak before, during, and after sputtering and to estimate the reacted oxygen amount. Most of the oxygen introduced into the chamaber was reacted during sputtering. As the partial pressure of oxygen increased, the oxygen content of the TbFeCoCr film increased also. The oxygen appeared to be bound as Tb-O, effectively decreasing the magnetically active Tb content of the film The coercivity decreased but the squareness of the Kerr hysteresis loops was still excellent. The perpendicular anisotropy was not significantly affected by oxygen amount. The carrier-to-noise ratio, includi!1g the write power sensitivity and bias field sensitivity did not change too much with oxygen content in the film The disks sputtered with oxygen showed better bias field sensitivity with lower write power threshold than the disk sputtered without oxygen, due to high demagnetization during domain formation. No significant degradation of coercivity for the disk sputtered oxygen was observed during an accelerated aging test.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.730-739
• /
• 2010

Stress history increases in penetration resistance due to the increase in residual horizontal stress of granular soil. This study analyzes the effect of stress history on the results of CPT and DMT from calibration chamber specimen in OC as well as NC state. Test results show that the normalized cone resistance by mean effective stress correlates well with the relative density and the state parameter, whereas the normalized cone resistance with regard to vertical effective stress is a little affected by stress history. The horizontal stress index($K_D$) in DMT more reflects the influence of stress history on granular soil than the dilatometer modulus($E_D$) and cone resistance($q_c$). The $K_D/K_0$, in which the effect of stress history on $K_D$ is compensated by the at-rest coefficient of earth pressure, $K_0$, is related to relative density, state parameter and the normalized cone resistance by mean effective stress. It is also observed that the normalized dilatometer modulus by mean effective stress($E_D/{\sigma_m}'$) is unique correlated with the state parameter, regardless of stress history.

• Journal of the Korea Concrete Institute
• /
• v.21 no.6
• /
• pp.781-788
• /
• 2009

Mechanical properties of steel-concrete interface were evaluated on the basis of experimental observations. The properties included bond strength, unbounded and bonded friction angles, residual level of friction angle, mode I fracture energy, mode II bonded fracture energy and unbonded slip-friction energy under different levels of normal stress, and shape parameters to define geometrical shape of failure envelope. For this purpose, a typical type of constitutive model of describing steel-concrete interface behavior was presented based on a hyperbolic three-parameter Mohr-Coulomb type failure criterion. The constitutive model depicts the strong dependency of interface behavior on bonding condition of interface, bonded or unbounded. Values of the interface parameters were determined through interpretation of experimental results, geometry of failure envelope and sensitivity analysis. Nonlinear finite element analysis that incorporates steel-concrete interface as well as material nonlinearities of concrete and steel were performed to predict the experimental results.