• Journal of the Korean Wood Science and Technology
• /
• v.49 no.6
• /
• pp.541-549
• /
• 2021

This paper reports a method to evaluate the residual strength of insect-damaged radiata pine lumber, such as the screw withdrawal strength as a semi-destructive method and a compression parallel to the grain test to assess the density changes after exposure to outdoor conditions. The screw withdrawal strength test was used as a semi-destructive method to estimate the residual density of decayed lumber. A compression parallel to the grain test was applied to evaluate the residual density. Three variables, such as the screw withdrawal strength, compression parallel to the grain, and residual density, were analyzed statistically to evaluate their relationships. The relationship between the residual density and screw withdrawal strength showed a good correlation, in which the screw withdrawal strength decreased with decreasing density. The other relationship between the residual density and compression parallel to the grain was also positively correlated; the compression parallel to the grain strength decreased with decreasing density. Finally, the correlation between the three variables was statistically significant, and the mutual correlation coefficients showed a strong correlation between the three variables. Hence, these variables are closely correlated. The test results showed that the screw withdrawal strength could be used as a semi-destructive method for an in situ estimation of an existing wood structure. Moreover, the method might approximate the residual density and compression parallel to the grain if supplemented with additional data.

• Journal of Environmental Science International
• /
• v.11 no.1
• /
• pp.41-56
• /
• 2002

In order to estimate the quantitative roles of the tide induced residual currents, density currents and wind driven currents on the residual currents in Kwangynag Bay Korea, numerical experiments with a diagnostic multi-level model were carried out. Density currents were calculated from the temperature and salinity data observed in January, May, August and November 1998. Anti-clockwise circulations are formed at the western inner part of the bay, the location from the east of Myodo Is. to the south of POSCO Co. and the place between Yeosu peninsula and Namhae Is. from the calculation results of the tide induced residual currents. Velocities of the density currents are less than 3cm/s at the western inner part of the bay and about 5cm/s at the southern entrance of the bay. Density currents get strong in summer and weak in autumn. Wind driven currents at the surface layer flow in the directions of the given winds which are the daily mean winds when the temperature and salinity observations are carried out. In the middle and lower layers, however the wind driven currents flow in the opposite direction to the surface currents as supplementary currents. The surface wind driven currents are greater than the tide induced residual currents or the density currents. The calculated residual currents including the tide induced residual currents, density currents and wind driven currents agree with the results of the current observations approximately. In the Bay, the wind driven currents affect on the residual currents greatestly and tide induced residual currents and density currents do in the second place and the third place.

• Journal of Korea Foresty Energy
• /
• v.20 no.2
• /
• pp.46-57
• /
• 2001

This study was conducted to provide tending operation information for the effective management in unmanaged artificial forests of Pinus densiflora for. erecta, Pinus rigida, and larix leptolepis, based on the study of the comparison of tree growth pattern by residual stand density after thinning practices. Followings are summarized results of this study. 1. The diameter growth of residual trees was increased as residual stand density decreased by thinning practices in the stands of Pinus densiflora for. erecta, and Pinus rigida, and subcompartment (Ga) and (Na) of Larix leptolepis. The statistical analysis noted that the tree growth was significantly different by the residual stand density. 2. The height growth did not show corresponding results by stand density treatment pattern, which indicated that the height growth was not directly influenced by residual stand density, but by site quality of the stand. 3. The diameter increment for the last six years was proportionately increased in larger diameter classes and less dense stands.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.6
• /
• pp.27-33
• /
• 2014

2nd stage of KSLV-I, NaRo-Ho, performs CCAM not to collide with Naro Science Satellite. At that moment, the satellite should pass through the Plume Density area which was generated by KSLV-I KM residual thrust. Therefore, it is necessary to predict Plume Density field of KM residual thrust and guarantee the safety of the trajectory of payload. In this paper, DSMC method was used to simulate Plume Density by KM residual thrust and the simulation showed that the trajectory of Naro Science Satellite was safe.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.566-567
• /
• 2006

The characteristics of residual stresses occurring in PM steel based nickel (FLN2-4405) was investigated. The measurements of residual stresses were carried out by electrochemical layer removal technique. The values and distributions of residual stresses occurring in PM steel processed under various densities and heat treatment conditions were determined. In most of the experiments, tensile residual stresses were recorded in surface of samples. The residual stress distribution on the surface of the PM steels is affected by the heat treatment conditions and density. Maximum values of residual stresses on the surface were observed sinter hardened condition and $7.4\;g/cm^3$ density. Minimum level of recorded tensile residual stresses are150 MPa and its maximum level is 370 MPa.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.4
• /
• pp.145-151
• /
• 2009

Nanocrystalline Cu thin films for FCCL were electrodeposited from sulfate baths to investigate systematically the influences of current density, solution pH on current efficiency, residual stress, surface morphology, and microstructure of thin Cu films. Current efficiencies were measured to be approximately 100%, irrespective of the applied current density and solution pH. But these influenced residual stress, surface morphology, XRD pattern, and grain size of electrodeposited Cu thin film. The residual stress decreased with decreasing the surface roughness, but increased with increasing the fcc(111) peak strength of XRD patterns.

• Journal of Environmental Science International
• /
• v.6 no.4
• /
• pp.313-322
• /
• 1997

In order to study the seasonal variation of kinetic and potential energy of residual flow field In Suyoung Bay of Korea, we calculated Its energy budget and compared It with the tidal energy there. The potential energy shows the large value In winter and spring and the small one In summer and early autumn when the density stratification Is developed. The kinetic energy of residual flow varies seasonally and the seasonally averaged kinetic energy of residual flow per unit area is 6.4$\times$$10^{-4}ergs s^{-1}cm^{-}2$. It Is mainly governed by the density-driven current with the exception of that In November when the kinetic energy of tide-induced residual current is larger than those of density-driven current and wind-driven current. An averaged traction of the kinetic energy of tide-Induced residual current, wind-driven current and density-driven current, which are the major components of residual flow, is 29.1%, 3.4%, 67.5%, respectively, to the kinetic energy of residual flow, The fraction of kinetic energy of residual flow, potential energy and tidal energy per unit area is 1.0 : 6.7$\times$$10^3$: 8.2$\times$$10^4$ respectively.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.58 no.2
• /
• pp.159-174
• /
• 2022

Flow prediction was carried out through observational survey and three dimensional multi-layered numerical diagnostic model experiment to clarify the time and spatial structure of tidal current and residual flow dominant in the sea exchange and material circulation of the waters around Geumo Islands in the southern waters of Korea. The horizontal variation of tidal current is so large that it causes asymmetric tidal mixing due to horizontal eddies and the topographical effect creating convergence and dispersion of flow direction and velocity. Due to strong tidal currents flowing northwest-southeast, counterclockwise and clockwise eddies are formed on the left and right sides of the south of Sori Island. These topographical eddies are created by horizontal turbulence and bottom friction causing nonlinear effects. Baroclinic density flows are less than 5 cm/s at coastal area in summer and the entire sea area in winter. The wind driven currents assuming summer and winter seasonal winds are also less than 5 cm/s and the current flow rate is high in winter. Density current in summer and wind driven current in winter have a relatively greater effect on the net residual flows (tidal residual current + density current + density driven current) around Geumo Islands Sea area.

• Journal of Korean Society of Water and Wastewater
• /
• v.27 no.5
• /
• pp.547-554
• /
• 2013

Chlorine has strong oxidizing power, also it is many advantages over other disinfectants such as the residual characteristic and economic feasibility. However, chlorine also has disadvantages such as creating disinfection by-products of chlorine as THMs. In particular, the most deadly disadvantage of chlorine is that it is extremely poisonous toxins about all alive lives. Disinfection with electrolysis water can be a very useful way Because you do not have to worry about chlorine's dangerous. In this study, we evaluated the potential as a disinfectant, across the evaluating disinfection effect and generating characteristic of by-products. The electrolyzed water could be obtained removal efficiencies of over 99.9 % the coliform by operating condition such as residence time, current density (voltage), the electrode gap. The residual chlorine be generated 10,000 mg/L in current density $1.0A/dm^2$ and residence time of 10 minutes. The residual chlorine concentration was possible to maintain a stable. The by-products generated by high concentration residual chlorine in the reactor such as trihalomethanes, haloaceticacid, chloralhydrate, haloacetonitrile were detected in less than a water quality standards. At the concentration of less than residual chlorine of 1 ppm, the chlorine disinfection by-products be generated most below the detection limit.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.6
• /
• pp.535-541
• /
• 1999

Low-dislocation-density large-diameter GaAs single crystals with low-residual-strain have been strongly required. We have developed dislocation-free 3-inch Si doped GaAs crystals for photonic devices, and low-dislocation-density low-residual-strain 4-inch to 6-inch semi-insulating GaAs crystals for electronic devices by Vertical Bridgman(VB) technique. We confirmed that VB substrates with low-residual-strain have higher resistance against slip-line generation during MBE process. VB-GaAs single crystals show uniform radial profile of resistivity reflecting to the flat solid-liquid interface during the crystal growth. Uniformity of micro-resistivity of VB-GaAs substrate is much better than of the LEC-GaAs substrate, which is due to the low-dislocation-density of VB-GaAs single crystals.