• Journal of Korean Society for Atmospheric Environment
• /
• v.27 no.6
• /
• pp.672-680
• /
• 2011

Three new granular absorbents were prepared from calcium hydroxide, and applied to an FGD process with internal circulation. The aim of the study was finding the most efficient of the these three applied absorbents for the $SO_2$ removal at high flue gas temperatures. The absorbent is fed to the testing unit at high operation temperature and fluidized inside the FGD system where the sorbent particles react with the $SO_2$ gas. The rate of $SO_2$ decomposition was high in C-type absorbent which had the large surface area. De-SOx characteristics of the current absorbents appeared to be similar to the other conventional agents in this fluidized bed combustor. In particular, the optimum de-SOx condition could be achieved at high mole ratios of Ca to S which can reduce the residual $SO_2$.

• Journal of Power System Engineering
• /
• v.18 no.3
• /
• pp.106-111
• /
• 2014

Welding is very popular method for joining two or more metals. However, welding causes residual stress and distortion and these give a bad influence to the structure strength. In this paper, TIG welding technique was performed to investigate the joint characteristics of AISI321 steel. For its evaluation, the orthogonal array method and variance analysis were applied with three factors of electric current, travel speed and argon gas and also three levels of each factor to tensile tests for optimum design. From the results, the increaser weld speed the narrower bead width and the lower weld penetration. The increaser electric current the brighter argon gas and the wider bead width. Also weld speed influenced most on the tensile strength and presumption range of tensile strength at optimal condition from reliability 95% was estimated to $635.02{\pm}14.64$. In addition the increaser weld speed and electric current the fracture occurred around bead vicinity.

• Tribology and Lubricants
• /
• v.25 no.4
• /
• pp.207-216
• /
• 2009

Friction tests were carried out in order to investigate the effects of temperature on the friction and wear behaviors between a PMMA film and a fused silica lens using a microtribometer. The friction forces on the PMMA film were measured under atmospheric condition as the temperature of the film was increased from 300 K to 443 K. The contact area between the film and the lens was observed. The tribological characteristics of the film were significantly changed as the temperature increased. The changes were discussed with the change of the film state from glassy to viscous flow. In addition, the results showed that the friction behavior can be varied with the thermal history of the PMMA film. Residual solvent in the PMMA film could emerge to the PMMA surface due to an additional heating and the solvent on the film surface decreased the friction force.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.4
• /
• pp.337-347
• /
• 2009

Generally, finite element models used in structural analysis have some uncertainties of the geometric dimensions, applied loads and boundary conditions, as well as in material properties due to the manufacturability of aluminum intensive body. Therefore, it is very important to refine or update a finite element model by correlating it with dynamic and static tests. The structural optimization problems of automotive body are considered for mechanical structures with initial stiffness due to preloading and in operation condition or manufacturing. As the mean compliance and deflection under preloading are chosen as the objective function and constraints, their sensitivities must be derived. The optimization problem is iteratively solved by a sequential convex approximation method in the commercial software. The design variables are corrected by the strain energy scale factor in the element levels. This paper presents an updated method based on the sensitivities of structural responses and the residual error vectors between experimental and simulation models.

• Korean Journal of Head & Neck Oncology
• /
• v.27 no.1
• /
• pp.66-69
• /
• 2011

Skull base osteoradionecrosis(ORN)is a rare complication of radiotherapy for nasopharyngeal carcinoma, but is one of the most severe and possibly fatal condition followed by radiotherapy. However, the treatment of skull base ORN has seldom been thoroughly described yet. Here we report a case of skull base ORN that was successfully treated with hyperbaric oxygen therapy(HBO). A 52-year-old man visited our department complaining of trismus and foul odor. He was diagnosed with nasopharyngeal cancer with multiple lymph node metastasis one year ago and underwent concurrent chemoradiotherapy. On the physical examination, mucopus and crusts with exposed necrotic bone was seen in the right nasopharynx. On the paranasal sinus magnetic resonance imaging, osteoradionecrosis which was extending from the right nasopharynx to the clivus, petrous apex, and cavernous sinus was noted. Nasopharynx biopsy resulted of ulcer with no malignant cells. HBO therapy was performed with debridement of nasopharynx for 3 months. There was no sign of recurrence or residual ORN 18 months after HBO therapy.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.5 no.1
• /
• pp.13-22
• /
• 2002

Stink bug, Canthecona furcellatta (Hemiptera: Pentatomidae), is an important predator of silkworm larvae. Nymphs and adult attack the early stage silkworm larvae and causes about 10-15 per cent loss to silk industry. Synthetic organic pesticides has tremendous impact on minimizing the pest population but repeated and frequent use has created problems of residual toxicity, development of resistance to insecticides, pest resurgence and out break, phyto-toxicity and hazards to non target species and beneficial organism. Silkworms are very sensitive to pesticides; therefore, attempt has made to control the bug population through introduction of its native natural enemies in the silkworm-rearing field. Biological control has tremendous scope in sericulture because it is eco-friendly in nature and non-harmful farmers. Native natural enemies have been screened. Psix striaticeps, Trissolcus spp. and Telenomus spp. have been recorded as the most potential parasitoid against pentatomid bug. Life cycle, sex ratio and other various attributes of the par-asitoids have been recorded. The parasitization potential of the parasitoid is very high and they have the ability to discriminate between parasitized and unpar-asitized host. Mass propopagation technique under laboratory condition has been standaydized.

• Journal of Welding and Joining
• /
• v.19 no.1
• /
• pp.27-32
• /
• 2001

This paper is studied about welding conditions and weldability of seam welding for galvanized steel sheet of automotive. The fuel tank of automobile is made by seam welding to be required of airtight or oiltight. This method have required a short time for welding, simplicity operation progress and little HAZ. Especially, it has more less residual stress and transformation than different welding progress. So, this study is for decreasing the leakage occurrence rate and to make standard operating condition table anyone can operate easily. Therefore, this study is analyzed the optimum conditions of seam welding for making the automobile with galvanized steel sheets by means of observing the microstructure and configuration back projection, RT, tensile-shear strengths test and SEM. Optimum conditions of seam welding obtained as follows, current 17.2-17.6kA speed 1.0m/min weld time 4:10:6 and current 16.5-17.4kA, speed 0.83m/min, weld time 4:10:4 at t1.0, and current, 18.5-18.9kA, speed 0.8m/min, weld time 4:10:4 and current 16.5-17.4kA, speed 0.68m/mi, weld time 4:10:2 at t1.6.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.43 no.2
• /
• pp.49-56
• /
• 2011

Mulching technique is used to control the temperature and moisture content of soil by covering the ground surface. Most kinds of mulching film are made of polyethylene which is non-biodegradable synthetic polymer. Utilizing these films has been one of the main sources in soil pollution. Thus residual films under the ground should be removed after a certain period of time. Therefore, an alternative mulching material made of biodegradable functional paper is considered instead of non-biodegradable films. The mulching sheet produced from paper basis has a functionality to be naturally degraded and then recycled to the bio-materials on soil. In this study, the paper based-mulching sheet coated with biodegradable polymer was specially produced using a laboratory bar coater. Coating colors prepared by dissolving PBS/PLA in chloroform were applied to kraft paper. The mechanical strength and aging properties of this mulching sheet were investigated. The burst strength of polymer-coated paper was decreased with the increase of the PBS ratio in PBS/PLA blends, and, in particular, 30/70 blending condition led to good stability in heat-aging atmosphere for 60 days.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.413-417
• /
• 1997

Distributed piezoelectric sensor and actuator have been designed for efficient vibration control of a cantilevered beam. Both PZT and PVDF are used in this study, the former as an actuator and the latter as a sensor for our integrated structure. For the PZT actuator, the position and size have been optimized. Optimal electrode shape of the PVDF sensor has been determined. For multi-mode vibration control, we have used two PZT actuators and a PVDF sensor. Electrode shading of PVDF is more powerful for modal force adjustment than the sizing and positioning of PZT. Finite element method is used to model the structure that includes the PZT actuator and the PVDF sensor. By deciding on or off of each PZT segment, the length and the location of the PZT actuator are optimize. Considering both of the host structure and the optimized actuators, it is designed that the active electrode width of PVDF sensor along the span of the beam. Actuator design is based on the criterion of minimizing the system energy in the control modes under a given initial condition. Sensor is designed to minimize the observation spill-over. Modal control forces for the residual(uncontrolled) modes have been minimized during the sensor design. Genetic algorithm, which is suitable for this kind of discrete problems, has been utilized for optimization. Discrete LQG control law has been applied to the integrated structure for real time vibration control. Performance of the sensor, the actuator, and the integrated smart structure has been demonstrated by experiments.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.5
• /
• pp.1661-1669
• /
• 2010

In this paper, I propose an Energy efficient Clustering based on Genetic Algorithm(ECGA) which reduces energy consumption by distributing energy overload to cluster group head and cluster head in order to lengthen the lifetime of sensor network. ECGA algorithm calculates the values like estimated energy cost summary, average and standard deviation of residual quantity of sensor node and applies them to fitness function. By using the fitness function, we can obtain the optimum condition of cluster group and cluster. I demonstrated that ECGA algorithm reduces the energy consumption and lengthens the lifetime of network compared with the previous clustering method by stimulation.