• The Korean Journal of Nuclear Medicine Technology
• /
• v.15 no.2
• /
• pp.26-29
• /
• 2011

Purpose: The general test method of the Korean Pharmacopeia specifies the test method on the clauses of quality control after manufacturing. According to KFDA Guidance for Medicines, standards of residual solvents regulates the maximum permissible dose of acetonitrile as 400 ppm, ethanol as 5,000 ppm, and acetic acid as 5,000 ppm. This study aims at identifying the type of resiual solvents in the final [F-18]FDG vial of an automatic synthesizer and measure its residual quantity. Materials and Methods: The center carried out residual solvents test of [F-18]FDG injection using Agilent Technologies 7890A with a Flame Ionization Detector. The column of Agilent Technologies 7890A used in measuring of residual solvents was CP WAX column ($30m{\times}0.53mm{\times}1.0{\mu}m$) and analysis condition was split mode 1:1 at the initial temperature $70^{\circ}C$ which was increased $20^{\circ}C/minute$ after two minutes and maintained at the final $140^{\circ}C$ for two minutes. The analysis method was as following: Firstly, ethanol-acetonitrile-acetic acid mixture was classified into four types of concentration (250-25-250 ppm, 1,000-100-1,000 ppm, 3,000-300-3,000 ppm, and 6,000-600-6,000 ppm), and $1.0{\mu}L$ of each type of concentration was injected into gas chromatography followed by an analysis of its peak domain. Then, a calibration-curve by the external standard method was drawn based on the analysis result. Results: While ethanol and acetonitrile were detected in TRACERlab MX, FASTlab had additional acetic acid. The residual quantity of the ethanol-acetonitrile-acetic acid mixture evaluated using the calibration-curve was average 72 ppm ethanol, 54 ppm acetonitrile, and 1030 ppm acetic acid for FASTlab, whereas average 439 ppm ethanol and 79 ppm acetonitrile for TRACERlab MX. This indicated that both of them were within the maximum permissible dose. Conclusion: Solvent residues in the [F-18]FDG injection were all within maximum permissible doses and proper to be used to examine a patient. The result indicated that types and quantities of solvent resides of radioactive pharmaceuticals vary depending on the automatic synthesizer.

• Korean Journal of Environmental Agriculture
• /
• v.14 no.3
• /
• pp.302-311
• /
• 1995

Benfuresate or oxolinic acid, as an experimental pesticide, was applied to the different textural paddy or upland soil respectively under the field condition and the residual concentrations were determined. Six kinetic models were employed to characterize the best-fit kinetic model describing the residual pattern of benfuresate or oxolinic acid and the $t\frac{1}{2}$ estimated from each model was comparatively assessed. All of the six models explained significantly the residual patterns of the pesticides but the empirical models such as PF, EL, and PB were not recommendable for the $t\frac{1}{2}$ estimation. Among theoretical models, the residual patterns were followed in the orders of the second-order(SO)>first-order(FO)>zero-order(ZO) kinetics, judging from the size and significance of coefficient of determination and standard error. However, the multiple FO model, consisting of the fast and slow decomposition steps, was better than the single FO model for the residual pattern and the $r^2$ in this case became similar to that of SO kinetic model. Thus the multiple FO and SO models were represented as the best fit model of the experimental pesticide. The $t\frac{1}{2}$ of benfuresate estimated from the single FO kinetic model in Weolgog and Cheongwon series was 49 and 63 days, respectively, which were 20 and 13% longer than the respective $t\frac{1}{2}$ from the SO kinetic model. The $t\frac{1}{2}$ of oxolinic acid from the FO model in Yonggye and Ihyeon series were 87 and 51% longer than those from the SO kinetic model, respectively. These results demonstrated that the best-fit model representing the residual pattern of a pesticide and the resultant $t\frac{1}{2}$ might be variable with the kinds of pesticides and the environmental conditions. Therefore it is recommended that the half-life of a pesticide be assessed from the best-fit model rather than from the FO kinetic model uniformly.

• Journal of Korean Society of Water and Wastewater
• /
• v.20 no.1
• /
• pp.71-78
• /
• 2006

The removal of protozoa in the coagulation process was evaluated under the different pH and turbidity using the jar test after the addition of polyaluminium chloride (PAC) as a coagulant. Two well-known protozoa of Cryptosporidium parvum and Giardia lamblia were tested at the same time with turbidity, the critical water quality parameter of the water treatment process. Both protozoa were removed about 1log (and up to 2log) at the optimum injection of PAC. The source water turbidity and pH affected the removal of protozoa and turbidity. At neutral and alkaline pH, 1.3-1.7log removal of protozoa for low turbid water with 5NTU, and 1.6-2.3log removal for high turbid water with 30NTU were achieved. However, at acidic pH, maximum 0.8-1.0log and 1.1-1.2log were removed for low and high turbid water, respectively, at the optimum PAC injection of 15mg/L. The relation of protozoa and turbidity removals were expressed as the 1st order equation (significantly positive relation) in the most of the tested conditions. In addition, the relation of protozoan removals with residual turbidity were also expressed the 1st order equation (significantly negative relation), although the significance of the equations were reduced at acidic pH. Therefore, residual turbidity could be a good index of efficient protozoan removal in the coagulation process, probably except at the low pH condition.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.2
• /
• pp.190-205
• /
• 2015

In this paper, the impact damage behavior of USN-150B carbon/epoxy composite laminates subjected to high velocity impact was studied experimentally and numerically. Square composite laminates stacked with $[45/0/-45/90]_{ns}$ quasi-symmetric and $[0/90]_{ns}$ cross-ply stacking sequences and a conical shape projectile with steel core, copper skin and lead filler were considered. First high-velocity impact tests were conducted under various test conditions. Three tests were repeated under the same impact condition. Projectile velocity before and after penetration were measured by infrared ray sensors and magnetic sensors. High-speed camera shots and C-Scan images were also taken to measure the projectile velocities and to obtain the information on the damage shapes of the projectile and the laminate specimens. Next, the numerical simulation was performed using explicit finite element code LS-DYNA. Both the projectile and the composite laminate were modeled using three-dimensional solid elements. Residual velocity history of the impact projectile and the failure shape and extents of the laminates were predicted and systematically examined. The results of this study can provide the understanding on the penetration process of laminated composites during ballistic impact, as well as the damage amount and modes. These were thought to be utilized to predict the decrease of mechanical properties and also to help mitigate impact damage of composite structures.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.4
• /
• pp.295-299
• /
• 2016

Residual foreign objects at the secondary side (top of the tubesheet and tube support plates) of a steam generator are likely to cause a leak by causing wear in the tube. The extent of wear is significantly affected by the material, shape, and size of the foreign object, and the corrosion properties of the tube. The presence of foreign objects at the top of the tubesheet and tube support plates has been identified using remote visual inspection methods such as the foreign object search and retrieval and eddy current test (ECT). The detection of the residual foreign object at the secondary side of a steam generator has limitations that depend on the material properties and the condition of contact with the tube. In this study, which is vertical and horizontal from the upper tubesheet, the corresponding bobbin ECT signals were collected and analyzed to measure its ability to detect foreign objects.

• Journal of the Society of Naval Architects of Korea
• /
• v.37 no.1
• /
• pp.67-81
• /
• 2000

An accurate and efficient numerical method for two-dimensional nonlinear radiation problem has been developed. The wave motion due to a moving body is described by the assumption of ideal fluid flow, and the governing Laplace equation can be effectively solved by the higher-order boundary element method with the help of the GMRES (Generalized Minimal RESidual) algorithm. The intersection or corner problem is resolved by utilizing the so-called discontinuous elements. The implicit trapezoidal rule is used in updating solutions at new time steps by considering stability and accuracy. Traveling waves caused by the oscillating body are absorbed downstream by the damping zone technique. It is demonstrated that the present method for time marching and radiation condition works efficiently for nonlinear radiation problem. To avoid the numerical instability enhanced by the local gathering of grid points, the regriding technique is employed so that all the grids on the free surface may be distributed with an equal distance. This makes it possible to reduce time interval and improve numerical stability. Special attention is paid to the local flow around the body during time integration. The nonlinear radiation force is calculated by the "acceleration potential technique". Present results show good agreement with other numerical computations and experiments.

• Journal of Environmental Health Sciences
• /
• v.39 no.3
• /
• pp.289-299
• /
• 2013

Objectives: For the field application of the dielectric barrier discharge plasma reactor, scale-up of the plasma reactor is needed. This study investigated the possibility of inactivation of microorganisms in sewage using pilot multi-plasma reactor. We also considered the possibility of degradation of total organic carbon (TOC) and nonbiodegradable matter ($UV_{254}$) in sewage. Methods: The pilot plasma reactor consists of plasma reactor with three plasma modules (discharge electrode and quartz dielectric tube), liquid-gas mixer, high voltage transformers, gas supply equipment and a liquid circulation system. In order to determine the operating conditions of the pilot plasma reactor, we performed experiments on the operation parameters such as gas and liquid flow rate and electric discharge voltage. Results: The experimental results showed that optimum operation conditions for the pilot plasma reactor in batch experiments were 1 L/min air flow rate), 4 L/min liquid circulation rate, and 13 kV electric discharge voltage, respectively. The main operation factor of the pilot plasma process was the high voltage. In continuous operation of the air plasma process, residual microorganisms, $UV_{254}$ absorbance and TOC removal rate at optimal condition of 13 kV were $10^{2.24}$ CFU/mL, 56.5% and 8.6%, respectively, while in oxygen plasma process at 10 kV, residual microorganisms, $UV_{254}$ absorbance and TOC removal rate at optimal conditions were $10^{1.0}$ CFU/mL, 73.3% and 24.4%, respectively. Electric power was increased exponentially with the increase in high voltage ($R^2$ = 0.9964). Electric power = $0.0492{\times}\exp^{(0.6027{\times}lectric\;discharge\;voltage)}$ Conclusions: Inactivation of microorganisms in sewage effluent using the pilot plasma process was done. The performance of oxygen plasma process was superior to air plasma process. The power consumption of oxygen plasma process was less than that of air plasma process. However, it was considered that the final evaluation of air and oxygen plasma must be evaluated by considering low power consumption, high process performance, operating costs and facility expenses of an oxygen generator.

• Resources Recycling
• /
• v.21 no.5
• /
• pp.44-49
• /
• 2012

In this study, the sonication method was applied to remove ink from old newspaper(ONP) using flotation. Results indicated increased whiteness and effective residual ink concentration (ERIC) with longer disintegration. Therefore 58% of whiteness and 182.9 ppm ERIC were obtained for 30 minutes of disintegration time without the change in yield. Longer disintegration than 30 minutes had no effects on whiteness without the application of ultra-sonication. On the other hand, higher than 58% of whiteness was achieved in 2 minutes of disintegration when the ultra-sonication was applied. The highest whiteness (59.32 %) was obtained by applying sonication for 20 minutes and froth flotation with kerosene as a collector under the alkaline condition (pH 11).

• Textile Coloration and Finishing
• /
• v.1 no.1
• /
• pp.54-62
• /
• 1989

The woven fabric composed of nylon 6 filaments was treated with aqueous solutions (20, 30, 40, 50, 60%) of formic acid at 3$0^{\circ}C$ for 10 minutes under unrestrained condition, and the shrinkage behavior and some kinds of properties were examined. The shrinkages of the constituent yarns and fabric were increased with formic acid concentration, but they were lower than that of the original filaments because of fabric-structural factors. And the shrinkage of the warp was lower than that of the weft because of the residual stress from weaving process. By the restraint forces such as fabric-structural factors and residual stress, the constituent filaments were damaged partially at 60% of formic acid concentration and the degree of damage on the warp was greater than on the weft. And though the fabric count were increased overall, the spacing between the warps was decreased prior to the weft and eliminated nearly at 60% of formic acid concentration. The thickness, tensile strength, elongation, and handle value of fabric were increased overall with formic acid concentration excepting that the tensile strength for both the warp and weft directions and the elongation for the warp direction were decreased instead by the damage of yarns. But the crease recovery was decreased except the case of the weft direction at 60% of formic acid concentration.

• Resources Recycling
• /
• v.12 no.6
• /
• pp.26-31
• /
• 2003

The power loss characteristics of Mn-Zn ferrite were observed with the sintering temperature. In case of $1150 ^{\circ}C$ sintering, the core loss increased with measuring temperature, and does not have minimum value at the point where the magnetocrystalline anisotropy be 'zero'. This reason mainly due to the change of core loss mechanism with grain size which affects residual loss. The grain size and sintered density slightly increased with equilibrium oxygen partial pressure at$ 1150 ^{\circ}C$ sintering. The resistivity and initial permeability showed no significance with atmosphere, these results due to complex effect of $Fe^{2+}$ concentration and microstructure change. The core loss at $100^{\circ}C$ decreased as the equilibrium oxygen partial pressure increased.e increased.