• Journal of the Korean Magnetics Society
• /
• v.14 no.3
• /
• pp.89-94
• /
• 2004

We have investigated magnetic properties of monolayer (ML)-thickness Co film deposited on InP(2${\times}$4) reconstruction surface using in situ Surface Magneto-Optical Kerr Effects (SMOKE) measurement system. InP(2${\times}$4) reconstruction surface, obtained by repeated sputtering and annealing, was confirmed by reflection hish energy electron diffraction (RHEED) and scanning tunneling microscope (STM) measurements. From both longitudinal and polar SMOKE measurements, we have observed three distinguishable regions showing different magnetic properties depending on the Co thickness. In the Co film thickness smaller than 7 $m\ell$, no SMOKE signal was detected. In the following thickness between 8 $m\ell$ and 15 $m\ell$, both longitudinal and polar Kerr hysteresis loops were observed, which implies a metastable phase coexisted of in-plane and perpendicular anisotropies. In the film thickness larger than 16 $m\ell$, only longitudinal MOKE signal without polar signal was detected, which implies existence of in-plane anisotropy in this thickness region.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.21 no.4
• /
• pp.388-394
• /
• 1999

To compare the effect of hyaluronate and dexamethasone on the temporomandibular joint arthrocentesis the author investigated 22 temporomandibular joint disorder(TMD) patients with pain and limitation of mouth opening who visited at the Department of Oral and Maxillofacial Surgery. Chosun Dental Hospital and were made a diagnosis as Wilkes stage III or IV of TMJ internal derangement clinically and radiographically. The two groups consisted of 10 patients with injection of sodium hyaluronate 10mg$(Artz^{(R)})$(hyaluronate group) on the upper joint space of the affected temporomandibular joint 5 times at intervals of a week after arthrocentesis, and 12 patients with injection of dexamethasone$(Oradexon^{(R)})$ at a time(dexamethasone group). Maximum mouth opening, pain value and satisfaction value during mastication were assessed on a visual analog scale before arthrocentesis and after 6 months. Then the within-group and between-group differences were evaluated in the obtained data and the clinical success rate of each group was calculated according to our success criteria. The results were as follows. 1. the mean of maximum mouth opening before arthrocentesis and after 6 months in the hyaluronate group were 24.9mm and 39.0mm respectively, and those before arthrocentesis and after 6 months in the dexamethasone group were 25.7mm and 41.3mm respectively. 2. The mean of pain value on a visual analog scale in the hyaluronate group before arthrocentesis and after 6 months were 6.7 and 1.8 respectively, and those in the dexamethasone group before arthrocentesis and after 6 months were 7.0 and 1.8 respectively. 3. The mean of satisfaction value during mastication on a visual analog scale in the hyaluronate group before arthrocentesis and after 6 months were 2.8 and 7.7 respectively, and those in the dexamethasone group before arthrocentesis and after 6 months were 3.1 and 7.8 respectively. 4. There were statistically significant differences between all measurements before arthrocentesis and after 6 months(P<0.001), but no difference between all measurements in the hyaluronate group and those in the dexamethasone group. 5. The over all success rate of the hyaluronate group and the dexamethasone group were 60.0% and 63.6% respectively. In summary, there was significant difference between the effect of hyaluronate and dexamethasone on the temporomandibular joint arthrocentesis but hyaluronate is better than corticosteroid as the injection drug in consideration of the side effect related with repeated injection.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.2
• /
• pp.111-123
• /
• 2019

In this paper, we propose a method for defining the input termination for on-wafer-type device under test (DUT) measurement. Using the newly defined input termination and noise wave correlation matrix (NWCM) measurement method based on noise power ratio, the NWCM of the on-wafer-type DUT was measured. We demonstrate a noise measurement configuration that includes wafer probes and bias tees to measure the on-wafer DUT. The S-parameter of the adapter that combines the bias tee, probe, and a line terminated by open is required to define the input termination for on-wafer DUT measurement. To measure the S-parameter of the adapter, a 2-port S-parameter measurement method using 1-port measurement is introduced. Using the measured S-parameters, a method for defining the new input termination for on-wafer-type DUT measurement is applied. The proposed method involves the measurement of the NWCM of the chip with a 1.5 dB noise figure. The noise parameters of the chip were obtained using the measured NWCM. The results indicate that the obtained values of the noise parameters are similar to those mentioned on a datasheet for the chip. In addition, repeated measurements yielded similar results, thereby confirming the reliability of the measurements.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.26 no.1
• /
• pp.49-61
• /
• 2021

The repeated shipboard measurements that have been conducted by the National Institute of Fisheries Science (NIFS) for more than a half century, provide the valuable long-term hydrographic data with high spatial-temporal resolution. However, this unprecedent dataset has been rarely used for oceanic climate sciences because of its reliability issue. In this study, temporal variability of salinity error in the NIFS data was quantified by means of extremely small variability of salinity in the deep layer of the south-western East Sea, in order to contribute to studies on long-term variability of the East Sea. The NIFS salinity errors estimated on the isothermal surfaces of 1℃ have a remarkable temporal variation, such as ~0.160 g/kg in the year of 1961~1980, ~0.060 g/kg in 1981~1994,~0.020 g/kg in 1995~2002, and ~0.010 g/kg in 2003~2014 on average, which basically represent bias error. In the recent years, even though the quality of salinity has been improved, there still remain relatively large bias errors in salinity data presumably due to failure of salinity sensor managements, especially in 2011, 2013, and 2014. On the contrary, the salinity in the year of 2012 was very accurate and stable, whose error was estimated as about 0.001 g/kg comparable to the salinity sensor accuracy. Thus, as long as developing proper data quality control procedures and sensor management systems, I expect that the NIFS shipboard hydrographic data could have good enough quality to support various studies on ocean response to climate variabilities. Additionally, a few points to improve the current NIFS shipboard measurements were suggested in the discussion section.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.27 no.3
• /
• pp.144-157
• /
• 2022

Noble gases, which are chemically inert and behave conservatively in marine environments, have been used as tracers of physical processes such as air-sea gas exchange, mixing of water masses, and distribution of glacial meltwater in the ocean. For precise measurements of Ne, Ar, and Kr, we developed a mass spectrometric system consisting of a quadrupole mass spectrometer (QMS), a high vacuum preparation line, an activated charcoal cryogenic trap (ACC), and a set of isotope standard gases. The high vacuum line consists of three sections: (1) a sample extraction section that extracts the dissolved gases in the sample and mixes them with the standard gases, (2) a gas preparation section that removes reactive gases using getters and separates the noble gases according to their evaporation points with the ACC, and (3) a gas analysis section that measures concentrations of each noble gas. The ACC attached to the gas preparation section markedly lowered the partial pressures of Ar and CO₂ in the QMS, which resulted in a reduced uncertainty of Ne isotope analysis. The isotope standard gases were prepared by mixing ²²Ne, ³⁶Ar, and ⁸⁶Kr. The amounts of each element in the mixed standard gases were determined by the reverse isotope dilution method with repeated measurements of the atmosphere. The analytical system achieved precisions for Ne, Ar, and Kr concentrations of 0.7%, 0.7%, and 0.4%, respectively. The accuracies confirmed by the analyses of air-equilibrated water were 0.5%, 1.0%, and 1.7% for Ne, Ar, and Kr, respectively.

• Corrosion Science and Technology
• /
• v.14 no.2
• /
• pp.47-53
• /
• 2015

Recently, the bending process is greatly applied to fabricate the pipe line. Bending process can reduce welding joints and then decrease the number of inspection. Thus, the maintenance cost will be reduced. Induction heat bending process is composed of bending deformation by repeated local heat and cooling. By this thermal process, corrosion properties and microstructure can be affected. This work focused on the effect of induction heating bending process on the properties of ASME SA106 Gr. C low carbon steel pipes. Microstructure analysis, hardness measurements, and immersion corrosion test were performed for base metal and bended area including extrados, intrados, crown up, and down parts. Microstructure was analyzed using an optical microscope and SEM. Hardness was measured using a Rockwell B scale. Induction heat bending process has influenced upon the size and distribution of ferrite and pearlite phases which were transformed into finer structure than those of base metal. Even though the fine microstructure, every bent area showed a little lower hardness than that of base metal. It is considered that softening by the bending process may be arisen. Except of I2, intrados area, the others showed a similar corrosion rate to that of base metal. But even relatively high rate of intrados area was very low and acceptable. Therefore, it is judged that induction heat bending process didn't affect boric acid corrosion behaviour of carbon steel.

• Journal of the Korean Society of Physical Medicine
• /
• v.8 no.3
• /
• pp.343-350
• /
• 2013

PURPOSE: The purpose of this study was to compare the effects of a combined non elastic taping and lumbar stabilizing exercise against lumbar stabilizing exercise only during the lumbar stabilizing exercise in chronic low back pain. METHOD: Thirty-one patients of low back pain were randomly allocated to 2 groups: lumbar stabilizing exercise group (n=16) and nonelastic taping group(n=15) with lumbar stabilizing exercise. Taping and stabilizing exercise were performed twice a week for 4 weeks. The patients were assessed using by visual analog scale (VAS) and Korean version of Oswestry disability index (KODI). The measurements of each patients were measured before the intervention and 2 weeks post-experiment and 4weeks after the intervention. All data were analyzed using by SPSS 12.0 software for Window, the experimental data was analyzed using by paired samples t-test and repeated ANOVA. All statistical tests in this study were conducted at the .05 level of significance. RESULTS: The results of this study are in the nonelastic taping group, significant difference were found in th VAS between pre-test and post-test (p<.05). In addition, there were significant differences in the VAS between the two groups at post-test(p<.05). And in the nonelastic taping group, significant difference were found in the KODI between pre-test and post-test (p<.05). However, there were no significant differences in the KODI between the two groups at post-test (p<.05). CONCLUSION: These findings suggest that combination of nonelastic taping and lumbar stabilizing exercise is more effective for low back pain than stabilizing exercise alone. In conclusion, this study indicates that stabilizing exercise combined with nonelastic taping would be recommended in the clinic.

• Asian-Australasian Journal of Animal Sciences
• /
• v.25 no.10
• /
• pp.1395-1403
• /
• 2012

The objective of the study was to quantify annual and seasonal differences in the chemical composition, in vitro gas production, in situ degradability and ruminal fermentation of grazing steers… diets. Diet samples were collected with four esophageal cannulated steers ($350{\pm}3$ kg BW); and four ruminally cannulated heifers ($342{\pm}1.5$ kg BW) were used to study the dry matter degradation and fermentation in rumen. Data were analyzed with repeated measurements split plot design. The crude protein, in vitro dry matter digestibility and metabolizable energy were higher during the first year of trial and in the summer (p<0.01). The values of calcium, phosphorus, magnesium, zinc and copper were higher in summer (p<0.05). The gas produced by the soluble and insoluble fractions, as well as the constant rate of gas production were greater in summer and fall (p<0.01). The ammonia nitrogen ($NH_3N$) and total volatile fatty acids concentrations in rumen, the soluble and degradable fractions, the constant rate of degradation and the effective degradability of DM and NDF were affected by year (p<0.05) and season (p<0.01). Our study provides new and useful knowledge for the formulation of protein, energetic and mineral supplements that grazing cattle need to improve their productive and reproductive performance.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.9
• /
• pp.3055-3060
• /
• 2012

A simple, rapid and sensitive spectrofluorometric method was developed for the determination of folic acid (FA), based on its quenching effect on the fluorescence intensity of enoxacin (ENX)-europium ($Eu^{3+}$) complex as a fluorescent probe. Fluorometric interaction between ENX-$Eu^{3+}$ complex and FA was studied using UV-visible and fluorescence spectroscopy. The quenched fluorescence intensity at an emission wavelength of 614 nm was proportional to the concentration of FA. Optimum conditions for the determination of FA were investigated. Under optimal conditions, the reduced fluorescence intensity at 614 nm was responded linearly with the concentration of FA. The linearity was maintained in the range of $1.25{\times}10^{-9}$ to $1.50{\times}10^{-7}$ M (R = 0.9986) with the limit of detection ($3S_b/m$) (where $S_b$ is the standard deviation of blank and m is the slop of linear calibration curve) of $6.94{\times}10^{-10}$ M. The relative standard deviation (RSD) for 9 repeated measurements of $1.0{\times}10^{-9}$ M FA was 1.42%. This method was simple, cost effective, and relatively free of interference from coexisting substances. Successful determinations of FA in pharmaceutical formulation and biological samples with the developed method were demonstrated.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.36T no.1
• /
• pp.19-24
• /
• 1999

$In_2O_3$-based thick films for the ozone detection of ppb range have been investigated. The $In_2O_3$ sensing layer is quite sensitive to ozone, but the saturated stable sensitivity cannot be obtained at the ozone exposure of 100 ppb for 5 min. The addition of $Fe_2O_3$ into $In_2O_3$ indicates some improvement in response time and sensitivity, but it seems the improvement is not good enough for real applications. Firing of $In_2O_3$:$Fe_2O_3$ powder induces remarkable improvement in response and recovery, although the sensitivity decrease. The sensing layer fired at $1300^{\circ}C$ and operated $550^{\circ}C$ shows excellent properties of fast response time, saturated stable sensitivity and rapid recovery characteristics to 100 ppb ozone exposure for 5 min. Especially, it shows the reproducibility of the sensor signal for repeated measurements and the linearity between the ozone concentration and the sensor resistance. The preliminary results clearly demonstrated that the sensor can be successfully applied for the ozone detection of ppb range.