• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.8
• /
• pp.63-70
• /
• 1992

Deposition properties and film characteristics of Remote PECVD silicon dioxide were investigated. Using $N_{2}O/SiH_{4}$, the effects of changing the process conditions` the pressure, the substrate temperature, and the gas mixing ration, on the film quality were observed. A comparison of film qualites of the Remote PECVD SiO$_2$ with that of a Direct PECVD SiO$_2$ was made. The experimental results show that the Remote PECVD SiO$_2$ has better electrical, physical, and annealing properties than the Direct PECVD oxide.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1995.11a
• /
• pp.93-94
• /
• 1995

• Journal of the Korean Vacuum Society
• /
• v.5 no.3
• /
• pp.223-228
• /
• 1996

$SiO_2$ insulator layers on InSb have been prepared by remote PECVD system a low temperature below $200^{\circ}C$. The effects of deposition pressure, temperature, and gas flow ratio on the physical and electrical characteristics of the $SiO_2$ were studied. The InSb MIS device using $SiO_2$ was fabricated and measured its current-voltage and capacitance-voltage characteritance-voltage charateristics at 77K. The films evaluated Auger electron spectroscopy showed that composition atoms were distributed uniformaly throughout the oxide film and the outdiffusion of substrate atoms into the oxide were few. The leakage current density of the MIS device was about 6.26nA/$\textrm{cm}^2$ at 0.75MV/cm , and the breakdown voltage was about 1MV/cm. The interface-stage density at mid-bandgap extracted from 1MHz C-V measurement was $54\times 10^{11}\textrm{cm}^2-2V^{-1}$.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.12
• /
• pp.59-64
• /
• 1996

InSb MIS devices prepared by remote PECVD SiO$_{2}$ were fabricated. The SiO$_{2}$ films on InSb were deposited at atemperature range of 67~190$^{\circ}$C. The effects of deposition temperature on the structural characteristics of the SiO$_{2}$ films evaluated Auger electron spectroscopy showed that atomic raito of silicon to oxygen was 0.5 and composition toms were distributed uniformaly throuout the oxide film. The transition region is about 100$\AA$ for SiO$_{2}$/InSb interface. The leakage current density at 1MV/cm and the breakdownelectric field of the MiS device using SiO$_{2}$ film deposited at 105$^{\circ}$C were about 22 nA/cm$^{2}$ and 3.5MV/cm, respectively. The interface-state density at mid-bandgap extracted from 1 MHz high frequency C-V measurement was about 2X10$^{11}$ cm$^{-2}$eV$^{-1}$.

• Electrical & Electronic Materials
• /
• v.8 no.2
• /
• pp.171-175
• /
• 1995

Optimum condition of remote plasma enhanced chemical vapor deposition using orthogonal array method was chosen. Characteristics of oxide films deposited by RPECVD with SiH$_{4}$ and N$_{2}$O gases were investigated. Etching rate of the optimized SiO$_{2}$ films in P-etchant was about 6[A/s] that was almost the same as that the high temperature thermal oxide. The films showed high dielectric breakdown field of more than 7[MV/cm] and a resistivity of 8*10$^{13}$ [.ohmcm] around at 7[MV/cm]. The interface trap density of SiO$_{2}$/Si interface around the midgap derived from the high frequency C-V curve was about 5*10$^{10}$ [/cm$^{2}$eV]. It was observed that the dielectric constant of the optimized SiO$_{2}$ film was 4.29.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.171-174
• /
• 1994

The drive towards ultra-large-scale integrated circuits a continuous intermetal dielectric films for multi layer interconection. Optimum condition of remote plasma enhanced chemical vapour deposition(RPECVD) was achieved by orthogonal array method. Chracteristics of SiO$_2$ films deposited by using remote PECVD with N$_2$O gas were investigated. Etching rate of SiO$_2$ films in P-echant was about 6[A/s] that was the same as the thermal oxide. The films a showed high breakdown voltage of 7(MV/cm) and a resistivity of Bx10$\^$13/[$\Omega$cm] at 7(MV/cm). The interface Trap density of SiO$_2$ has been shown excel lent properties of 5x10$\^$10/[/$\textrm{cm}^2$eV]. It was observed that the dielectric constant dropped to a value of 4. 29 for 150 [W] RF power.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.258-258
• /
• 2011

Solar Cell의 TCO로써 연구중인 ZnO 박막을 제조함에 있어 Remote ICP PECVD 방법으로 개발된 공정기술을 응용하여 공정 변수인 소스간의 혼합비율, 공정압력, 공정온도, 플라즈마 파워 등의 공정조건을 조절하여 박막의 표면구조 및 (박막) 특성을 제어하는 것이 가능하다. 공정조건을 조절하여 박막두께와 표면결정크기를 변화시킴에 따라 광학적 특성의 변화가 발생하였으며 표면결정크기와 Haze 율이 관계가 있음을 확인하였다. 일반적으로 CVD 법에 의한 ZnO 박막의 표면결정크기는 박막의 두께가 증가함에 따라 성장하지만 공정조건의 조절을 통해 동일두께에서 결정크기의 조대화가 가능함을 알 수 있었다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.97-97
• /
• 2009

원격 고주파 원도결합 플라즈마 증착공정을 이용하여 태양광의 반사도를 낮추고, 흡수효율을 개선할 수 있는 피라미드형 표면구조를 가지느니 투명전동성 ZnO 박막을 높은 증착속도로 증착할 수 있는 공정조건을 찾기 위하여 반응압력, $H_{2}O$/DEZn 유량비, 플라즈마 출력과 기판온도에 대하여 실험하였다. 실험결과 400$\sim$600nm/min 이상의 높은 증착속도을 얻을 수 있었으며, 넓은 공정 영역에서 안정적인 피라미드 표면 구조를 가지는 공정조건을 확보하였다. 증착된 박막의 표면구조와 물분석 결과와 공정조건과의 관계에 대한 연구 결과를 발표할 예정이다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1994.02a
• /
• pp.133-133
• /
• 1994

• Proceedings of the Korean Vacuum Society Conference
• /
• 1994.02a
• /
• pp.144-145
• /
• 1994