• Archives of Metallurgy and Materials
• /
• v.64 no.2
• /
• pp.571-578
• /
• 2019

The densification behavior of H13 tool steel powder by dual speed laser scanning strategy have been characterized for selective laser melting process, one of powder bed fusion based metal 3d printing. Under limited given laser power, the laser re-melting increases the relative density and hardness of H13 tool steel with closing pores. The single melt-pool analysis shows that the pores are located on top area of melt pool when the scanning speed is over 400 mm/s while the low scanning speed of 200 mm/s generates pores beneath the melt pool in the form of keyhole mode with the high energy input from the laser. With the second laser scanning, the pores on top area of melt pools are efficiently closed with proper dual combination of scan speed. However pores located beneath the melt pools could not be removed by second laser scanning. When each layer of 3d printing are re-melted, the relative density and hardness are improved for most dual combination of scanning. Among the scan speed combination, the 600 mm/s by 400 mm/s leads to the highest relative density, 99.94 % with hardness of 53.5 HRC. This densification characterization with H13 tool steel laser re-melting can be efficiently applied for tool steel component manufacturing via metal 3d printing.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.2
• /
• pp.67-71
• /
• 2003

Using motions (Maruo) and wave reflection (the author), speed loss due to wind (van Berlekom) and ITTC standard spectrum, and various effects of weather(:such as weather intensity, ship type, ship size and draught) on ship speed performance at sea were investigated. Further, a comparison of the relative effects of weather and hull roughness on speed loss was also studied for a VLCC.

• Journal of the Korean Society of Safety
• /
• v.16 no.2
• /
• pp.130-135
• /
• 2001

The additional stresses and displacements produced by the use of long rail, typical of the high-speed railway, are investigated for the Taiwan high-speed railway bridges. In addition, an important special feature of the Taiwan high Speed Railway Design Specifications specifies that service earthquake has to be considered during the rail-structure interaction analysis before evaluating the stresses and relative displacements of the bridge. As pound motion is taken into account under seismic event the seismic response of the structure is applied as displacement in the rail-structure interaction analysis. The stresses and relative displacements of the structure are checked according to the consideration of seismic loading.

• Korean Journal of Applied Biomechanics
• /
• v.17 no.4
• /
• pp.27-36
• /
• 2007

The purpose of this study was to investigate the effect of the upper body in order to increase a propulsive force in the old's walking. The subjects were each 10 males, the latter term of the aged and former term of the aged. There were three walking speeds of slow(about 5km/h), medium(about 6km/h), and maximum speed(about 7km/h). The subjects walking 11m were filmed the 5m section (from 3m to 8m) by 2-video cameras using three dimensional cinematography. And we computed different mechanical quantities and especially computed the relative momentum in order to achieve this study's aim. In this study, we was able to acquire some knowledge. The step length and step frequency increased in proportion to the walking speed, and the faster walking speed, the shorter ratio of supporting time( both legs supporting time/one step length time). When it was one leg support phase, the torso was indicated to generate the momentum in order to produce the propulsive force of walking. The upper and lower body had a cooperative relation for walking such as keeping step rate with the arms to legs and maintaining the body balance. The opposition phase for upward-and-downward direction of the torso and arms in walking was functioned to prevent the increase rapidly toward vertical direction of the center of gravity. The arms had contributed to coordinate the tempo of legs and the posture maintenance of the upper body. And by absorbing the relative momentum from the upper torso with arms to the lower torso, it had the rhythmical movement on upward-and-downward direction reducing the vertical reaction force. On account of the relations of absorption and generation of the propulsive force and the production of vertical impulse in the lower torso when walking by maximum speed, it was showed that the function of lower torso was come up as important problem for the mechanical posture stability and propulsive force coordination.

• Proceedings of the KSR Conference
• /
• 2004.06a
• /
• pp.1180-1187
• /
• 2004

Relative displacements between decks should be within the allowable limit under horizontal forces in high-speed railway bridges. Longitudinal force transmitters(LFT) have been introduced ih high-speed railway bridges for test track. The horizontal forces on the pier supporting the fixed bearing are transmitted to the near piers supporting the sliding bearings by LFT, The performance of LFT was investigated by field test in which the braking and acceleration tests using KTX were conducted in Baebang viaduct. The relative displacements between decks were measured infield test and were compared with the numerical results and the allowable limit.

• Journal of Advanced Marine Engineering and Technology
• /
• v.19 no.2
• /
• pp.81-91
• /
• 1995

A miniature size electrostatic induction motor has been fabricated and studied with emphasis on the role of the surface resistivity, the relative dielectric constant of the rotor surface materials and the rotor liner materials, which control the charge induction and relaxation on the rotor surface and the field intensity between the rotor and the stator. It is found that the higher resitivity and/or the higher relative dielectric constant, concurrently the longer relaxation time constant of the rotor surface materials make the motor speed get higher speed. In case of discrete coated rotor surface it is found that the motor speed was increased logarithmically as narrow as width of the discrete coated Ti. And the degree of width of discrete coated Ti to the axial direction of the rotor was $60^{\circ}$ and $150^{\circ}$, the motor has got a 125% higher than that at the degree of $0^{\circ}$.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.65-68
• /
• 2003

This study is intended to look into the influence of environment and construction factor on bleeding of concrete. According to the results, as wind is light, relative humidity is high and temperature is low, the amount of bleeding increases greatly, and evaporation speed is influenced greatly by order of wind, temperature and humidity. As the properties of bleeding by construction factor, the amount of bleeding increases with an increase of placing thickness, but the bleeding ratio, the amount of bleeding per unit volume, increases with a decrease of the placing thickness. Bleeding speed is fastest at about 90 minute after placing concrete. Also, as wind is light, relative humidity is high, temperature is low and the placing thickness is thick, bleeding speed grow faster.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.478-481
• /
• 2009

As a first step for aerodynamic analysis of vertical axis wind turbine, dynamic stall characteristics of airfoil was investigated. Dynamic stall of wind turbine airfoil is caused by severe variation of angle of attack and relative velocity of flow around airfoil. Angle of attack and relative velocity can be expressed with tip speed ratio. Variation of angle of attack is strongly dependent on the tip speed ratio. For tip speed ratio, 1.4 and free stream velocity, 15m/s, dynamic stall characteristics of wind turbine airfoil is compared with those of oscillating airfoil having same angle of attack variation.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2015.09a
• /
• pp.28-33
• /
• 2015

Speed log measurement has always been of utmost importance to the mariners. To date the most accurate maritime speed measurement comes from Doppler measurement, where speed may be measured relative to either water(speed through water) or seabed(speed over ground). Recently, a clarification has been issued by the International Maritime Organization (IMO) regarding the speed measuring devices, which could ultimately impact the final arrangement of these devices for ships being constructed after July 1, 2014. This paper will discuss the clarification in depth and necessary action which shall be taken by the owners and operators of the ships impacted.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.2
• /
• pp.101-105
• /
• 2006

Disk radial runout creates a periodic relative motion between the laser beam spot and tracks formed on an optical disk. While only focus control is activated, the periodic relative motion yields sinusoid-like waves in the tracking error signal, where one cycle of the sinusoid-like waves corresponds to one track. The frequency of the sinusoid-like waves varies depending on the disk rotational speed and the amount of the disk radial runout. If the frequency of the tracking error signal in the off-track state is too high due to large radial runout of the disk, it is not a simple matter to begin track-following control stably. It might take a long time to reach a steady state or tracking control might fail to reach a stable steady state in the worst case. This article proposes a simple method for reducing the relative motion caused by the disk radial runout in the off-track state. The relative motion in the off-track state is effectively reduced by a drive input obtained through measurements of the tracking error signal and simple calculations based on the measurements, which helps reduce the transient response time of the track-following control. The validity of the proposed method is verified through an experiment using an optical disk drive.