• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.40 no.1
• /
• pp.37-44
• /
• 2014

Preservatives such as paraben, phenoxyethanol, and chlorphene are commonly used in cosmetics thanks to cheap price and good antiseptic effect. Recently, consumers' concerns about their possible toxicity and skin irritation forced them to be replaced with straight 1,2-alkanediols. However, as the alkanediols may also irritate skin, limited amount of them should be used in cosmetics. Three 1,2-alkanediols including 1,2-pentanediol, 1,2-hexanediol, and 1,2-octanediol in cosmetics were analyzed simultaneously by gas chromatogrphy with flame ionization detector. As a result of method validation, the specificity was confirmed by the calibration curves of 1,2-pentanediol, 1,2-hexanediol, and 1,2-octanediol showing good linearity correlation coefficient of above 0.999 over the concentration range of $100{\sim}1,200{\mu}g/g$. The limit of detection (LOD) and quantification (LOQ) of 1,2-pentanediol, 1,2-hexanediol, and 1,2-octanediol were 31, 40, and $19{\mu}g/g$ and 98, 108, and $57{\mu}g/g$, respectively. The precision (Repeatability) of the amount in cosmetics showed less than 2.0%. Relative Standard Deviation (% RSD) and the Accuracy (% recovery) of the amount in cosmetics showed 99.3 ~ 103.3, 99.4 ~ 106.7, 97.5 ~ 107.3% respectively. As a result, simultaneous analysis of antimicrobial three 1,2-alkanediols in cosmetics were possible. This method can be utilized in accurate quantitative analysis of 1,2-alkanediols in cosmetics.

• Journal of Bio-Environment Control
• /
• v.10 no.4
• /
• pp.213-218
• /
• 2001

In 2000, domestic protected cultivation area was about 52,189 ha including 13,621 ha of heating greenhouses. Recently, heating cost accounts for 25 to 30% of total production cost which has been increased due to the rise of oil price, while the heating cost was about 15% in other advanced countries. To reduce the heating energy cost, the study of minimizing the heating space of greenhouse have been conducted from 1998 to 1999. The system was developed to control the heating space according to crop growth by moving horizontal curtain up and down. Installation of the heating space-control curtain in greenhouse decreased heating capacity to 264 m$^3$compared to 661.5 m$^3$in the traditional curtain, and consumpted fuel was saved about 56% point in semiforcing culture and 28% point in retarding culture of pepper. In addition, uniform distribution of air temperature and relative humidity in greenhouse environment resulted in earlier flowering and higher yields in hot pepper.

• Environmental and Resource Economics Review
• /
• v.13 no.3
• /
• pp.337-366
• /
• 2004

Contingent Valuation Method (CVM), as non-market valuation approach, has been criticized on that respondents may not realistically reflect their budget constraints in answering willingness to pay (WTP) for hypothetical CV questions. This paper empirically estimates the income calibration factor associated with CV responses through combining travel cost method and contingent valuation method in a utility-theoretic framework. The joint model of recreation demand function and contingent WTP function was applied to an important case study on the Man Kyoung River system, whose water quality is at issue because of the Sae Alan Kum reclamation project. Relevant economic variables such as price, income and water quality had significant influence as anticipated by the economic theory. Equally important, the income calibration factor was not significantly different from one, suggesting that the systematic discrepancies of CV responses relative to the actual behavior was not detected at least in terms of budget exaggeration. Overall, this study supports the notion that carefully designed CVM studies can provide informative data on individuals' willingness to pay for environmental quality changes.

• Journal of Mushroom
• /
• v.8 no.1
• /
• pp.11-15
• /
• 2010

The word spawn is derived from an old French verb, espandre, meaning to spread out or expand. Spawn is also defined as "the mycelium of fungi, especially of mushrooms grown to be eaten, used for propagation". The effects of bag spawn to sawdust substrate on the growth of Pleurotus ostreatus were conducted. The duration of mycelial growth and days of pinhead formation of bag spawn(2.5kg) were 18~19days and 7~8days, whereas bottle spawn ($1,000m{\ell}$) was 18days and 6days, respectively. The yield of mushroom fruitbody was that bag spawn is 100~118g, bottle spawn is 95~115g. In economical analysis, bag spawn is increased to 50%, compared to bottle spawn in relative income.

• The Korean Journal of Applied Statistics
• /
• v.29 no.1
• /
• pp.85-98
• /
• 2016

This study makes an empirical comparison of various realized volatilities (RVs) in terms of overnight returns. In financial asset markets, during overnight or holidays, no or few trading data are available causing a difficulty in computing RVs for a whole span of a day. A review will be made on several RVs reflecting overnight return variations. The comparison is made for forecast accuracies of several RVs for some financial assets: the US S&P500 index, the US NASDAQ index, the KOSPI (Korean Stock Price Index), and the foreign exchange rate of the Korea won relative to the US dollar. The RV of a day is compared with the square of the next day log-return, which is a proxy for the integrated volatility of the day. The comparison is made by investigating the Mean Absolute Error (MAE) and the Root Mean Square Error (RMSE). Statistical inference of MAE and RMSE is made by applying the model confidence set (MCS) approach and the Diebold-Mariano test. For the three index data, a specific RV emerges as the best one, which addresses overnight return variations by inflating daytime RV.

• Journal of Service Research and Studies
• /
• v.7 no.4
• /
• pp.51-68
• /
• 2017

Financial technology (FinTech) is an emerging financial service sector include innovations in financial literacy and investment, retail banking, education, and crypto-currencies like bitcoin. One of the crucial branch of financial technology-third-party payment (TPP) is undergoing rapid growth, with online/mobile systems replacing offline financial systems. System quality and user attitudes are key perceptions driving third-party payment usage, the importance of these perceptions, however, may be different with countries as users' thinking varies from country to country. Thus, the purpose of this study is to elaborate how factors differ from China to Korea by drawing on the unified theory of acceptance and use of technology (UTAUT2). Additionally, this study also aims to propose a multi-attribute evaluation of the third-party online payment system based on analytic hierarchy process (AHP), fuzzy sets and technique for order performance by similarity to ideal solution (TOPSIS), to examine the relative importance of the perceptions influencing new technology adoption intention. The results showed that the price value has the most significant influence on Chinese perceptions, while the perceived credibility has the most significant effect on Korean perceptions. Sub-criteria also performs different results to Chinese and Korean third-party online payment system.

• The Journal of Korean Academy of Prosthodontics
• /
• v.37 no.2
• /
• pp.212-234
• /
• 1999

Dental restorative materials must have the physical properties to withstand wear and corrosion. Base metal alloys possess better mechanical properties and lower price than the gold alloys. For these reasons such alloys have largely replaced the precious metal alloys. One aspect to con-sider is the release of metal substances to oral environment. The release of elements from dental alloys is a continuing concern because the elements may have the potentially harmful biological effects on local tissues. The purpose of this study was to minimize metal release on the nonprecious metal surfaces by ion beam assisted deposition(IBAD) of titanium nitride (TiN) Ni-Cr-Be alloys with and without TiN coatings were secured in an wear test machine opposing ruby ball to determine their relative resistance to wear with loom, 200m, 300m and 400m sliding distance. And the corrosion behavior of the Ni-Cr-Be alloys with and without TiN coatings and 3 dental noble alloys have been studied. Potentiodynamic curves were used to analyse the corrosion characteristics of the alloys. The measurement of the released Ni and Cr ions was conducted by analysis of the electrolyte solution with atomic absorption spectroscopy. The results were as follows : 1. The critical sliding distance that wore down TiN coatings of $2.5{\mu}m$ thickness in this study condition was 300m. 2. Ion beam assisted deposition of TiN showed a good surface modification with respect to the properties of wear and corrosion resistance. 3. X-ray diffraction showed that the strongest peak of TiN is TiN(111) in the coatings. 4. The release of Ni and Cr ions from alloys measured by means of atomic absorption spectroscopy was reduced by ion beam assisted deposition of TiN.

• Journal of Animal Science and Technology
• /
• v.57 no.5
• /
• pp.17.1-17.6
• /
• 2015

The present study investigated the nutritional and economic suitability of cashew reject meal (full fat and defatted) as replacement for groundnut cake (GNC) in the diets of laying chickens. A total of eighty four brown shavers at 25 weeks of age were randomly allotted into seven dietary treatments each containing 6 replicates of 2 birds each. The seven diets prepared included diet 1, a control with GNC at $220gkg^{-1}$ as main protein source in the diet. Diets 2, 3 and 4 consist of gradual replacement of GNC with defatted cashew reject meal (DCRM) at 50%, 75% and 100% on weight for weight basis respectively while diets 5, 6 and 7 consist of gradual inclusion of full fat cashew reject meal (FCRM) to replace 25%, 35% and 50% of GNC protein respectively. Each group was allotted a diet in a completely randomized design in a study that lasted eight weeks during which records of the chemical constituent of the test ingredients, performance characteristics, egg quality traits and economic indicators were measured. Results showed that the crude protein were 22.10 and 35.4% for FCRM and DCRM respectively. Gross energy of DCRM was 5035 kcal/kg compared to GNC, 4752 kcal/kg. Result of aflatoxin $B_1$ revealed moderate level between 10 and $17{\mu}g/Kg$ in DCRM and GNC samples respectively. Birds on control gained 10 g, while those on DCRM and FCRM gained about 35 g and 120 g respectively. Feed intake declined (P < 0.05) with increased level of FCRM. Hen day production was highest in birds fed DCRM, followed by control and lowest value (P < 0.05) was recorded for FCRM. No significant change (P > 0.05) was observed for egg weight and shell thickness. Fat deposition and cholesterol content increased (P > 0.05) with increasing level of FCRM. The cost of feed per kilogram decreased gradually with increased inclusion level of CRM. The prediction equation showed the relative worth of DCRM compared to GNC was 92.3% whereas the actual market price of GNC triples that of DCRM. It was recommended that GNC could be completely replaced by DCRM in layer's diets in regions where this by product is abundant. However, FCRM should be cautiously used in diets of laying chickens.

• Journal of Distribution Science
• /
• v.13 no.1
• /
• pp.83-91
• /
• 2015

Purpose - Despite the structural irrationality of multi-level transportation and the oil price rise, the domestic freight transportation market continues to grow, mirroring the rise in e-commerce and resultant increase in courier services and freight volumes. Several studies on courier services have been conducted. However, few studies or statistics have been published regarding regular freight services although they have played a role in the freight service market. The present study identifies the characteristics of regular freight service users to seek competitiveness enhancement measures specific to regular freight services. Research design, data, and methodology - IPA is a comparative analysis of the relative importance of and satisfaction with each attribute simultaneously. This study used IPA because it facilitates the process of analyzing importance and performance, deriving implications and a visual understanding of results. To enhance the competitiveness of regular freight services, this study surveyed its current users regarding the importance of the regular freight service factors. A total of 200 copies of a questionnaire were circulated and 190 copies were returned. In addition to demographics, respondents answered questions about the importance of and satisfaction with services on a 5-point Likert scale. Excluding 3 inappropriate copies, 187 out of 190 copies were analyzed. PASW Statistics 18 was used for statistical analysis. A total of 20 question items were selected for the service factors presented in the questionnaire based on the 1st pilot survey and previous studies. Results - According to the IPA performed to compare the importance of and satisfaction with service factors, both importance and satisfaction are high in the 1st quadrant, which involves the economic advantage of using regular freight services, quick arrival at destinations, weight freight handling, and less time constraints on freight receipt/dispatch. This area requires continuous management. Satisfaction is higher than importance in the 2nd quadrant, which involves the adequacy of freight, cost savings over ordinary courier services, notification on freight arrival, and freight tracking information. This area requires intensive investment and management. Satisfaction is lower than importance in the 3rd quadrant, involving the credit card payment system, courier delivery service, distance to freight handling sites, easy access to freight handling sites, and prompt problem solving. This area requires further intensive management. Both importance and satisfaction are low in the 4th quadrant, involving the availability of collection service, storage space at freight handling sites, kindness of collection/delivery staff, kindness of outlet staff, and easy delivery checks. This area is a set of variables should be excluded from priority control targets. Conclusions - Based on the IPA, service factors that need priority controls because of high importance and low satisfaction include the credit card payment system, delivery service, distance to freight handling sites, easy access to freight handling sites, and prompt problem solving. The findings need to be applied to future marketing strategies for regular freight services and for developing competitiveness enhancement programs.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.41 no.3
• /
• pp.168-175
• /
• 2021

The optimal determination of seeding rate is critical to minimizing uncertainties about the large variations observed in forage quality and productivity when alfalfa is cultivated under different geographical areas and growing conditions. The objective of this investigation was to provide information about the proper seeding rate according to harvest timing for alfalfa cultivation in the Northern regions of Korea. Alfalfa was sown in September 2018 at a seeding rate of 20, 30 or 40 kg/ha and harvested four times in 2019: May 3, July 2, September 11, and October 13. Regardless of seeding rate, alfalfa plant height was longest at the third harvest (113 cm) and the shortest in the last annual harvest (43.8 cm). However, seeding rate had no effect on alfalfa plant height at any harvest. Forage relative feed value was increased in the first cutting but decreased in the third cuttings as seeding rate increased. However, seeding rate had slight effect on alfalfa forage quality components at the second and fourth cuttings. Total annual DM and crude protein production (in 4 harvests) was greater at higher seeding rates. Plots seeded at a rate of 40 kg/ha produced on average 1,257 and 2,620 kg/ha more forage (DM basis) than those seeded at a rate of 30 or 20 kg/ha, respectively. Forage DM production at the first, second, third, and fourth harvests accounted for 36.1, 24.0, 27.1, and 12.8 % of total annual DM production, respectively. Overall, small differences were seen when alfalfa seeding rate was different but maximum forage DM production (in four harvests) was detected when seeding rate was 40 kg/ha. These data could be useful to the alfalfa growers by allowing them to make more accurate trade-offs between seed price and the expected magnitude of forage yield gains in order to select the best seeding rate.