• Journal of the Korean Applied Science and Technology
• /
• v.27 no.3
• /
• pp.378-384
• /
• 2010

Regenerated cellulose was prepared from Buckeye wood pulp V60 via dissolution in N-methylmorpholin N-oxide (NMMO) solvent system. The effect of antioxidants such as, n-propylgallate (PG), tris(nonylphenyl) phosphite (TRIS), ethylenediamine tetraacetic acid disodium salt (EDTA), and magnesium sulfate on the properties of regenerated cellulose was studied using X-ray diffraction, copper index calculation, and viscometry. Only addition of more than 0.01% of PG into NMMO solvent was effective to avoid the reduction of the degree of polymerization(DP) of regenerated cellulose during dissolution at $110^{\circ}C$. However, the early stage(within 0.5h of dissolution process) degradation of cellulose was not prevented eventhough up to 0.5% PG was appled to hot NMMO system. In addition, to recover the expensive NMMO after cellulose regenerating process, the washing filtrate was studied using simple techniques, such as refractive index, pH, and conductivity measurements. Through conductivity measurement result, 4-time of washing was enough to remove the NMMO completely from regenerated cellulose.

• Journal of the Korean Applied Science and Technology
• /
• v.27 no.4
• /
• pp.508-514
• /
• 2010

Regenerated cellulose fibers were prepared from three pulps containing different degree of polymerization(DP) and $\alpha$-cellulose contents by dry-jet wet spinning technique with cellulose dope in N-methylmorpholin N-oxide (NMMO). The effect of antioxidant, n-propyl gallate (PG) on the properties of different regenerated celluloses was studied using X-ray diffraction, copper number calculation, and viscometry. The degradaqtion of regenerated cellulose from pulp containing higher DP and lower $\alpha$-cellulose content was occurred more seriously. The tensile strength and initial modulus of regenerated cellulose fiber obtained from NMMO dope with PG were higher than those of fiber obtained from NMMO dope without PG. All fibers showed the round shape cross section and typical cellulose II crystalline structure.

• Fibers and Polymers
• /
• v.6 no.2
• /
• pp.95-102
• /
• 2005

Sodium cellulose carbonate (CC-Na) dissolved in $8.5\;wt\%$ NaOH/ZnO (100/2-3, w/w) aqueous solution was spun into some acidic coagulant systems. Diameter of regenerated cellulose fibers obtained was in the range of $15-50\;{\mu}m$. Serrated or circular cross sectional views were obtained by controlling salt concentration or acidity in the acid/salt/water coagulant systems. Velocity ratio of take-up to spinning was controlled up to 4/1 with increasing spinning velocity from 5 to 40 m/min. Skin structure of was developed at lower acidity or higher concentration of coagulants. Fineness, tenacity and elongation of the regenerated cellulose fibers were in the range of 1.5-27 denier, 1.2-2.2 g/d, and $8-11.3\;\%$, respectively. All of CC-Na and cellulose fibers spun from CC-Na exhibited cellulose II crystalline structure. Crystallinity index was increased with increasing take-up speed.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.41 no.4
• /
• pp.237-242
• /
• 2008

The tunic of Styela clava(SCT) consists of a proteoglycan network. Regenerated cellulose films were prepared by solution casting and coagulation of SCT in N-methylmorpholine-N-oxide(NMMO)/$H_2O$(87/13 wt%). The crystalline structure of powdered SCT was primarily that of cellulose I. The crystalline structure of SCT films exhibited a cellulose II structure, similar to that of viscose rayon. Physical characterization of SCT films and fibers revealed an intrinsic viscosity($\eta$) of 6.35 dL/g, average molecular weight($M_w$) of 423,000 g/M, and fiber density of 1.50 $g/cm^3$ with a moisture regain and water absorption of 10.20% and 365%, respectively. The results were similar to those of cellulose films regenerated from wood pulp. Films prepared with 6 wt% SCT exhibited strong tensile strength, high water absorption, and a greater degree of elongation. Scanning electron micrographs(SEM) of film cross-sections showed a layered, sponge-like structure.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.2
• /
• pp.56-65
• /
• 2013

Electron beam treatment was applied for improving dissolution of cellulose with ionic liquids. Two ionic liquids, 1-allyl-3-methylimidazolium chloride ([Amim]Cl]: AC) and 1,3-dimethylimidazolium methylphosphite ([Dmim][$(MeO)(H)PO_2$]: Me) were used for this experiment. Treatment with electron beams up to dose of 400 kGy resulted in the increase of hot water extract and alkali extract of cotton pulp and the great reduction in the molecular weight of cellulose. For the dissolution of cotton pulp with two ionic liquids, the electron beam treated samples showed faster dissolution. The dissolved cellulose with Me ionic liquid were regenerated with acetonitrile and the structure of regenerated cellulose showed distinct difference depending on the electron beam treatment. Those results provide the electron beam pre-treatment could be applied as an energy efficient and environmentally benign method to increase the dissolution of cellulose with ionic liquids.

• Proceedings of the Korean Fiber Society Conference
• /
• 2000.04a
• /
• pp.125-128
• /
• 2000

Chemical cellulose from an ascidian tunic is isolated by extraction, digestion and bleaching steps. The content of $\alpha$-cellulose was above 98 wt%, and it's DPw was about 918. A new regenerated cellulose fiber from the chemical cellulose obtained in this study was made using NMMO/water(87/13 wt%) as a solvent by dry jet-wet spinning. The effects of spinning speed and cellulose content of spinning dope on the properties were investigated.

• Textile Coloration and Finishing
• /
• v.33 no.4
• /
• pp.258-268
• /
• 2021

This study conducted on the introduction of recycled cellulose fibers, which are widely used in the textile industry as eco-friendly biomass materials, into polypropylene resins, which are mainly used for interior and exterior materials such as door trims and console parts of automobiles. In general, cellulose fibers can affect mechanical properties and have a lightening effect when used as a reinforcing agent. However, since cellulose fibers have hydrophilic properties and have relatively low compatibility with industrial polymer resins, they are used in combination through fiber hydrophobic surface treatment. Therefore, through this study, the reforming reaction conditions optimized in terms of hydrophobicity and workability for cellulose fibers are studied. Furthermore, polypropylene containing surface-modified cellulose fibers was prepared to compare physical properties by fiber content and study optimized content.

• Proceedings of the Korean Fiber Society Conference
• /
• 2001.04b
• /
• pp.55-58
• /
• 2001

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.6
• /
• pp.89-97
• /
• 2015

In this study, dissolution characteristics of 60% LiBr aqueous solution for Miscanthus sinensis holocellulose in accordance with heating time and characteristics of regenerated films were analyzed. Miscanthus sinensis holocellulose was made by peracetic acid method. During the dissolution of 60% LiBr solution for the holocellulose, the dissolution was started from the tip of the cellulose fiber after about 7 minutes, and proceeded as it swollen like a balloon. A lot of Si was identified by analyzing hollocellulose regenerated film through SEM/EDS. Cross section of regenerated film as dissolution time till 40 minutes of dissolution showed multilayered structure and fiber orientation. But after 40 minutes, multilayered structure and fiber orientation was not observed. The crystal structure of the holecellulose was transformed cellulose I into cellulose II. Therefore, dissolution for 20 minutes with 60% LiBr solution in the condition of $190^{\circ}C$ hot plate was shown as an optimum condition to manufacture the holocellulose regenerated film.

• Proceedings of the Korean Fiber Society Conference
• /
• 2002.04a
• /
• pp.359-362
• /
• 2002

이산화탄소($CO_2$)를 사용한 셀룰로오스 카보네이트 유도체의 제조 및 재생 셀룰로오스 섬유 제조와 관련한 기초 연구성과를 이미 발표한 바 있다[1~4]. 이번 연구에서는 일정한 조건에서 제조된 셀룰로오스 카보네이트 유도체를 10 wt% NaOH 수용액계에 용해시켜 방사용액(spinning dope)을 제조하고 일욕의 습식 방사장치를 이용하여 재생 셀룰로오스 섬유를 제조하였다. 이때 사용된 응고욕으로 황산, 초산, 인산 수용액계를 사용하였으며 제조된 각각의 재생 셀루로오스 섬유에 대해 물성분석을 하였다. (중략)