• Journal of the Korean Ceramic Society
• /
• v.54 no.5
• /
• pp.429-437
• /
• 2017

Micro hollow plate type silica with low refraction properties was synthesized and its hollow structure was applied as an optical structure to develop a light diffusion material that simultaneously satisfies the requirements of good light diffusibility, high transmissibility, and high luminance. The developed light diffusion material was applied to a light diffusion film and the film's optical properties were assessed. Hollow silica was synthesized by precipitation method using $Mg(OH)_2$ core particles, sodium silicate, and ammonium sulfate as the silica precursors. The concentration of the silica precursor was adjusted to control hollow silica shell thickness. The total light transmittance of the light diffusion film composed of the hollow silica was 94.55%, which was 4.57% higher than that of the PC film; new film's haze was 71.20%, which was 70.9% higher. Furthermore, the luminance increased by 5.34% compared to that of the light source. The reason for the results is not only that the micro plate type hollow silica, which has a low refractive property, played a role in reducing the difference in refractive index between the medium boundaries, but also that there was a light-concentrating effect due to the changing of light paths to the front direction inside the hollow structure. Optical simulation verified the enhanced optical properties when hollow silica was applied to the light diffusion film.

• Journal of Korean Society on Water Environment
• /
• v.25 no.4
• /
• pp.547-552
• /
• 2009

Because of refractory property of light, the travel path of UV light becomes longer than the straight line and shorter solely in water as UV light passes sequentially through air, quartz and water. Note that water significantly absorbs UV light. Hence, UV intensity shall be estimated to be lower when refraction is neglected than it is considered. Reflection is also critical for the design of UV radiation system. While the reflection at the interface of air and quartz is low enough to ignore, it is too high to be ignored at the interface of quartz and water. Assuming constant power, smaller length to width ratio of UV reactor is beneficial and single-lamp system is preferred to multi-lamps. Under the given cross section, optimal lamp positions could be decided. For example of an elliptical reactor with dual lamps, the optimal lamp locations shall be the 1/3 and 2/3 position of the longer axis.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.2
• /
• pp.178-185
• /
• 2016

In this study, we have fabricated light guide plates (LGPs) in thin film form for edge type back light unit (BLU) by using UV imprint lithography. In the LGPs, the pattern of functional resins on PC and PMMA substrates were successfully transferred from original master mold through PVC stamp. Optimized pattern arrays with slowly-sloped density were designed to obtain high brightness and uniformity. We could obtain a relatively improved brightness of $950cd/m^2$ and a uniformity of 87.3% by using the NP-S20 functional resins at an input power of 1.3 W because NP-S20 resin could show high formability after UV hardening process. The LGP prepared on polymethylmethacrylate (PMMA) substrate exhibited higher brightness than that on polycarbonate (PC) substrate because PMMA has lower refractive index resulting in more refraction toward the vertical direction.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.429-429
• /
• 2007

In this study, it was investigated about the variation of luminance properties in LED backlight with geometrical shape such as prism or lens shape on the light-entering face. Generally, LED light source has the loss in backlight system because it has horizontal direction light. PMMA(Poly-Methyl-Meta-Acrylate) is used LGP(Light-Guide-Plate) in conventional backlight system. PMMA has low refraction angle. so that. horizontal direction light was not used in backlight system. The addition of geometrical shape in light-entering face in LGP improves the luminance characteristics because it prevents horizontal direction light generation in light-entering-face. Prism or lens shape in same pitch disposition was almost same without these treatment such as the value of 1% rising. Besides. It is particular that the gap of these shape such as the value of 0.407~0.22mm prevents horizontal direction light, so then it contributes luminance rising at 5.6%.

• Journal of Korean Elementary Science Education
• /
• v.41 no.2
• /
• pp.283-294
• /
• 2022

Although the concept of light is important in the elementary school curriculum, substantial research suggests that students and teachers have difficulties in understanding it. Therefore, it is necessary to analyze the reasons for these difficulties-whether it is due to the content or due to the presentation method of contents, structure, and expression. The national curriculum and textbooks of Korea, the US, China, and Japan were comparatively analyzed from the following perspectives: 1) key concepts of light, 2) structure of light units in the textbook, 3) materials, light sources, and optics used in light units. Consequently, there were differences between countries in their inclusion of the concept of light in the curriculum. In particular, the Korean curriculum studies the concept of refraction by a convex lens, whereas the concept of light, light source, and vision is not introduced. Furthermore, countries also differed in their structuring of units. The Korean curriculum was presented segmentally by concept rather than structured according to core ideas or perspectives, and the connection between concepts was unclear. In addition, there were differences between the countries in materials, light sources, and optical instruments to explain key concepts. On using light, the US curriculum provides a purpose and uses light to achieve it, and China and Korea understand the concept. It was divided into the method of using the material to deepen. Based on the results of this analysis, the implications for the elementary science curriculum in Korea were derived as follows. First, it is necessary to introduce concepts sequentially and organize them so that the connection between concepts is well expressed. Second, it is necessary to introduce light and light sources as the predominant concepts. Third, it is necessary to include the principle of seeing objects. Fourth, it is necessary to adjust the material and content level of the refraction concept included in the light and lens unit. Fifth, an integrated approach is required because light has a deep connection with various concepts included in the elementary science curriculum.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.12
• /
• pp.60-66
• /
• 2011

There are several technological problems have to be resolved for LEDs to be used as a general purpose light source. In addition, there are several differences between existing luminaires and the general planer LED luminaire for the intensity distribution. Therefore, the optical engineer then faces the challenging a problem of designing for a spatially extended and non-uniform light source. In the previous studies on the optical design of luminaires, a lot of studies on reflectors and light source have been conducted but the ones on prisms and lenses are insufficient at present. This study developed the numerical model of planar prism LED luminaire to control luminous intensity distribution of LED luminaires. And this study presents an optical calculation process for the prism optical design of a planar prism LED luminaire and a comparison of the simulation results between the developed numerical model and Photopia 2.0 to verify the accuracy of the numerical model. In addition, this study showed a method for the control of various luminous intensity distribution from the developed numerical model.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.6
• /
• pp.471-476
• /
• 2010

This paper has studied dissymmetrical light distribution design using the secondary optics in the simulation. fundamental Lambertian radiation distribution based on LED has been cut off by the secondary optics, and the first surface slope of lens and second surface slope of total reflection area have been calculated through formula. PMMA (the index of refraction: 1.49361) which is material of lens has been selected. critical angle($42.02993^{\circ}$) between Air and PMMA has been calulated by snell's law, and total reflection angle slope has been selected about $16.67^{\circ}$ to occur the total reflection. when the first surface slope and the second surface slope has been set up, Rays of all total reflection area have generated the total reflection. finally, designed LED Module has been estimated by Korean Industrial Standards for LED safety street lighting. dissymmetrical light distribution have been analyzed with reached effect of road illuminance, and average road illuminance which are each 70.6 lx, 40.35 lx, and 25.88 lx have been satisfied with Korean Industrial Standards for LED safety street lighting.

• Korean Journal of Metals and Materials
• /
• v.46 no.6
• /
• pp.377-381
• /
• 2008

Prism sheet of LCD BLU which depends on supply from Japan and U.S.A was studied by using Si anisotropic etching and injection molding technologies. First, the prism sheet was patterned on Si wafer through photolithography, and the best conditions of Si etching were determined through etching Si wafer with TMAH to obtain straight optimized zigzag patterns, and a cross pattern to provide light diffusion and concurrent focusing. The etch rate of TMAH was concluded to be constant for $25wt%-70^{\circ}C$ condition. Ni stamp of prism sheet was made by electrodeposition using patterned Si wafer, normal or fast H/C(Heating/Cooling) injections were carried out to fabricate prism sheet. It was known that fast H/C injection could fabricate prism sheet more accurately than normal injection. Zigzag patterns and the cross pattern showed higher transmissivity than the straight patterns because of light diffusion through diagonal direction. The fast H/C injection for zigzag patterns showed lower transmissivity than normal injection because there occurred more light diffusion through precise injection patterns, but the fast H/C injection for straight patterns showed only refraction without diffusion, causing lower transmissivity than normal injection.

• Design & Manufacturing
• /
• v.13 no.4
• /
• pp.40-44
• /
• 2019

The light diffusion component spreads the light from one point evenly over a large area. Various types of light diffusion parts such as films and lenses are applied in the high-tech industries such as LCD display devices, lighting devices, and solar energy generation. Among these, a diffuser sheet (Diffuser Sheet) has a function to uniformly distribute the light, and various studies have been conducted to improve its function. The shape of the conventional light diffusion pattern is mainly made of a dot or hemispherical shape. In this study, a rectangular cone-shaped structure having a light diffusion function and an advantage of controlling the angle of refraction of light was fabricated by using a solenoid indentation process. The change in shape of the indentation structure was analyzed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.174-174
• /
• 2014

Memristor devices are one of the most promising candidate approaches to next-generation memory technologies. Memristive switching phenomena usually rely on repeated electrical resistive switching between non-volatile resistance states in an active material under the application of an electrical stimulus, such as a voltage or current. Recent reports have explored the use of variety of external operating parameters, such as the modulation of an applied magnetic field, temperature, or illumination conditions to activate changes in the memristive switching behaviors. Among these possible choices of signal controlling factors of memristor, photon is particularly attractive because photonic signals are not only easier to reach directly over long distances than electrical signal, but they also efficiently manage the interactions between logic devices without any signal interference. Furthermore, due to the inherent wave characteristics of photons, the facile manipulation of the light ray enables incident light angle controlled memristive switching. So that, in the tautological sense, device orienting position with regard to a photon source determines the occurrence of memristive switching as well. To demonstrate this position controlled memory device functionality, we have fabricated a metal-semiconductor-metal memristive switching nanodevice using ZnO nanorods. Superhydrophobicity employed in this memristor gives rise to illumination direction selectivity as an extra controlling parameter which is important feature in emerging. When light irradiates from a point source in water to the surface treated device, refraction of light ray takes place at the water/air interface because of the optical density differences in two media (water/air). When incident light travels through a higher refractive index medium (water; n=1.33) to lower one (air; n=1), a total reflection occurs for incidence angles over the critical value. Thus, when we watch the submerged NW arrays at the view angles over the critical angle, a mirror-like surface is observed due to the presence of air pocket layer. From this processes, the reversible switching characteristics were verified by modulating the light incident angle between the resistor and memristor.