• Journal of Energy Engineering
• /
• v.26 no.3
• /
• pp.131-136
• /
• 2017

Automobile engine oil is the most important lubricant for operating as the engine is started. Recently, manufacturers of the automotive industry and lubricants are considerably improving the quality of oil with additive to extend change cycle period. Most customers are recommended genuine oil among different types from shop expert. Through this report we suggest another reference point for consumer to pick highly efficient lubricant. This report is investigated oil compounds to compare with 6 different automotive considering actual running condition for 7 months. we conducted experiment from physical and chemical perspectives. In the field, through various experiments oil compounds between mineral oil and synthetic oil are largely distinguished in oxidation, viscosity, fluid and TBN. These are influenced by engine part wear as piston, bearing etc. Comparing various investigation with different oil the performance of synthetic oil is shown better condition in flash point, oxidation stability and also found less in change pollutant iron, Al compounds. Additives of oil show clear difference Ca level in detergent-dispersant both mineral oil and synthetic oil. And Zn in extreme pressure additives and P in Lubricity improver make no difference to both.

• Journal of Radiation Protection and Research
• /
• v.31 no.1
• /
• pp.37-46
• /
• 2006

For the first step to develop a reference disposal container of spent fuel to be used in a deep geological repository, this paper examined safe dimensions of the disposal container on the points of nuclear criticality and radiation safety and mechanical structural safety and provided basic information for dimensioning the container and configuration of the container components, and establishing the favorable and safe disposal conditions. When the safety factor for stress due to the external loads (hydrostatic and swelling pressure) is taken as 2.0, the safe diameter of the filler material to provide enough container strength under the assumed external loads is found to be 112cm with 13cm spacing between inner baskets in PWR container. Also the thickness of the thinner section between the fuel basket and the surface of the cast insert is determined to be 150 mm. Regarding these dimensions of the container, the PWR fuel container is sketched to accommodate 4 square assemblies or 297 CANDU fuel 297 bundles (33 circle tubes x 9 stacks). However the top and bottom parts need to be checked again through the detail radiation shielding analysis with respects to the emplacement position and handling processes of the disposal container.

• Nutrition Research and Practice
• /
• v.12 no.3
• /
• pp.258-264
• /
• 2018

BACKGROUND/OBJECTIVES: Diet quality scores or indices, based on dietary guidelines, are used to summarize dietary intake into a single numeric variable. The aim of this study was to examine the association between the modified diet quality index for Koreans (DQI-K) and mortality among Health Examinees-Gem (HEXA-G) study participants. SUBJECTS/METHODS: The DQI-K was modified from the original diet quality index. A total of 134,547 participants (45,207 men and 89,340 women) from the HEXA-G study (2004 and 2013) were included. The DQI-K is based on eight components: 1) daily protein intake, 2) percent of energy from fat, 3) percent of energy from saturated fat, 4) daily cholesterol intake, 5) daily whole-grain intake, 6) daily fruit intake, 7) daily vegetable intake, and 8) daily sodium intake. The association between all-cause mortality and the DQI-K was examined using Cox proportional hazard regression models. Hazard ratios and confidence intervals were estimated after adjusting for age, gender, income, smoking status, alcohol drinking, body mass index, and total energy intake. RESULTS: The total DQI-K score was calculated by summing the scores of the eight components (range 0-9). In the multivariable adjusted models, with good diet quality (score 0-4) as a reference, poor diet quality (score 5-9) was associated with an increased risk of all-cause mortality (hazard ratios = 1.23, 95% confidence intervals = 1.06-1.43). Moreover, a one-unit increase in DQI-K score resulted in a 6% higher mortality risk. CONCLUSIONS: A poor diet quality DQI-K score was associated with an increased risk of mortality. The DQI-K in the present study may be used to assess the diet quality of Korean adults.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.6 no.2
• /
• pp.119-128
• /
• 2008

Thermal assessment of a new CANDU spent fuel disposal system, which improves the retrievability of the spent fuel and enhances the densification factor compared with the Korean Reference disposal System, is carried out in this study. The canisters for CANDU spent fuels are stored for long term and cooled by natural convection in the proposed disposal system for the retrievability. The steady state thermal analyses for proposed CANDU disposal system are carried out with the ANSYS 10.0 CFX code. The thermal analyses are performed through two steps. At the first step, the sensitivity of the disposal tunnel spacing is analysed. The differences of maximum temperatures by several tunnel spacings are calculated at three points in the disposal tunnel. The result shows that the differences of the temperature at the three points are almost negligible because 99% of the decay heat is removed by natural convection. At the second procedure, 60m tunnel spacing with a ventilation system instead of natural convection is considered. The result is applied to the calculation of the canister surface temperature in disposal tunnel as boundary conditions. Consequently, the average and the maximum surface temperature of disposal canisters are $79.9^{\circ}C$ and $119^{\circ}C$, respectively. The inner maximum temperature of a basket in the disposal canister is calculated as $140.9^{\circ}C$. The maximum temperature of the basket meets the thermal requirement for the CANDU spent fuel cladding.

• Journal of the Korea Society of Computer and Information
• /
• v.18 no.11
• /
• pp.77-86
• /
• 2013

In this paper, we propose a fast video retargeting method which preserves the contents of a video and converts the image size. Since the conventional Seam Carving which is the well-known content-aware image retargeting technique uses the dynamic programming method, the repetitive update procedure of the accumulation energy is absolutely needed to obtain seam. The energy update procedure cannot avoid the processing time delay because of many operations by the image full-searching. By applying the proposed method, frames which have similar features in video are classified into a scene, and the first frame of a scene is resized by the modified Seam Carving where multiple seams are extracted from candidate seams to reduce the repetitive update procedure. After resizing the first frame of a scene, all continuous frames of the same scene are resized with reference to the seam information stored in the previous frame without the calculation of the accumulation energy. Therefore, although the fast processing is possible with reducing complexity and without analyzing all frames of scene, the quality of an image can be analogously maintained with an existing method. The experimental results show that the proposed method can preserve the contents of an image and can be practically applied to retarget the image on real time.

• Korean Journal of Remote Sensing
• /
• v.34 no.6_1
• /
• pp.925-939
• /
• 2018

Absorbed shortwave radiation at the surface is an important component of energy analysis among the atmosphere, land, and ocean. In this study, the absorbed shortwave radiation was calculated using a radiation model and surface broadband albedo data for application to Geostationary Earth Orbit Korea Multi-Purpose SATellite (GEO-KOMPSAT-2A; GK-2A). And the results (GWNU algorithm) were compared with CERES data and calculation results using pyranometer and MODIS (Moderate Resolution Imaging Spectroradiometer) data to be selected as the reference absorbed shortwave radiation. This GWNU algorithm was also compared with the physical and statistical algorithms of GOSE-R ABI and two algorithms (Li et al., 1993; Kim and Jeong, 2016) using regression equation. As a result, the absorbed shortwave radiation calculated by GWNU algorithm was more accurate than the values calculated by the other algorithms. However, if the problem about computing time and accuracy of albedo data arise when absorbed shortwave radiation is calculated by GWNU algorithm, then the empirical algorithms explained above should be used with GWNU algorithm.

• Tunnel and Underground Space
• /
• v.28 no.6
• /
• pp.528-546
• /
• 2018

Cases of TBM tunnelling have been consistently increasing worldwide. In many recent subsea and urban tunnelling projects, TBM excavation has been preferably considered due to its advantages over drill and blast tunnelling. Difficult ground conditions are highly probable to appear in subsea and urban tunnels because of the shallow working depth and alluvial characteristics. Under the difficult ground conditions, ground reinforcement measures should be considered including grouting, while it is of great importance to select the optimal grout material and injection method to cope with the ground condition. The benefits from TBM excavation, such as fast excavation, increased safety, and reduced environmental impact, can be achieved by applying appropriate ground reinforcement with the minimum overrun of cost and time. In this report, various grouting methods were reviewed so that they can be applied in difficult ground conditions. In addition, domestic and international cases of successful ground reinforcement for difficult grounds were introduced for future reference.

• Tunnel and Underground Space
• /
• v.31 no.1
• /
• pp.10-24
• /
• 2021

Rock mass classification for construction of underground facilities is essential to secure their stabilities. Therefore, the reliable values for rock mass classification from the precise information on rock discontinuities are most important factors, because rock mass discontinuities can affect exclusively on the physical and mechanical properties of rock mass. The conventional classification operation for rock mass has been usually performed by hand mapping. However, there have been many issues for its precision and reliability; for instance, in large-scale survey area for regional geological survey, or rock mass classification operation by non-professional engineers. For these reasons, automated rock mass classification using LiDAR becomes popular for obtaining the quick and precise information. But there are several suggested algorithms for analyzing the rock mass discontinuities from point cloud data by LiDAR scanning, and it is known that the different algorithm gives usually different solution. Also, it is not simple to obtain the exact same value to hand mapping. In this paper, several discontinuity extract algorithms have been explained, and their processes for extracting rock mass discontinuities have been simulated for real rock bench. The application process for several algorithms is anticipated to be a good reference for future researches on extracting rock mass discontinuities from digital point cloud data by laser scanner, such as LiDAR.

• Geophysics and Geophysical Exploration
• /
• v.24 no.3
• /
• pp.113-130
• /
• 2021

Recently, ground-penetrating radar (GPR) surveys have been actively employed to obtain a large amount of data on occurrences such as ground subsidence and road safety. However, considering the cost and time efficiency, more intuitive and accurate interpretation methods are required, as interpreting a whole survey data set is a cost-intensive process. For this purpose, GPR data can be subjected to attribute analysis, which allows quantitative interpretation. Among the seismic attributes that have been widely used in the field of exploration, complex trace analysis and similarity are the most suitable methods for analyzing GPR data. Further, recently proposed attributes such as edge detecting and texture attributes are also effective for GPR data analysis because of the advances in image processing. In this paper, as a reference for research on the attribute analysis of GPR data, we introduce the useful attributes for GPR data and describe their concepts. Further, we present an analysis of the interpretation methods based on the attribute analysis and past cases.

• Journal of the Korean Society of Radiology
• /
• v.16 no.6
• /
• pp.719-725
• /
• 2022

This study aimed to measure, quantitatively evaluate, and set the criteria for the minimum lead(Pb) shield thickness per level of clinically applied electron beam energy. The lead shield thickness per electron beam energy was measured using the primary field 95% reduction based on the open field at the depth of maximum dose (d_max) and depth from the surface as the reference depth of tissue dose(10 mm). The measured values were 1.906 mmPb and 1.992 mmPb at the d_max and 10 mm, respectively, regarding the lead shield thickness for 6 MeV electron beam; 2.746 mmPb and 3.743 mmPb for 9 MeV electron beam, 3.718 mmPb and 6.093 mmPb for 12 MeV electron beam, 7.300 mmPb and 15.270 mmPb for 16 MeV electron beam, and 16.825 mmPb and 25.090 mmPb for 20 MeV electron beam. Consequently, a thicker lead shield was required if the measurement was at 10 mm. The required lead shield thickness was also higher than that of the theoretical formula for electron beams of ≥ 16 MeV.