• Journal of Korean Society for Quality Management
• /
• v.20 no.2
• /
• pp.94-108
• /
• 1992

This study involves an experiment for the cognitive experiment design and the human reliability in software engineering. Its overall objectives are to analyze common-cause human domain error and reliability in human-software interaction. A laboratory study was performed to analyze software engineers' task behavior in software production and to identify software design factors contributing to the effects in common cause failure redundancy. Common-cause model and its function were developed, then the main experiment using programming experts was conducted in order to define a new cognitive paradigm, in the aspects of identification, pattern recognition, and behavior domain for human reliability and quality control in software development. The results and analytical procedures developed in this research can be applied to reliability improvement and cost reduction in software development for many applications. Results are also expected to provide guidelines for software engineering quality control and for more effective design of human-software interface system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.101-116
• /
• 2002

Modern vehicles require a high degree of refinement, including good driveability to meet customer demands. Vehicle driveability, which becomes a key decisive factor for marketability, is affected by many parameters such as engine control and the dynamic characteristics in drive lines. Therefore, Engine and drive train characteristics should be considered to achieve a well balanced vehicle response simultaneously. This paper describes analysis procedures using a mathematical model which has been developed to simulate spark timing control logic. Inertia mass moment, stiffness and damping coefficient of engine and drive train were simulated to analyze the effect of parameters which were related vehicle dynamic behavior. Inertia mass moment of engine and stiffness of drive line were shown key factors for the shuffle characteristics. It was found that torque increase rate, torque reduction rate and torque recovery timing and rate influenced the shuffle characteristics at the tip-in condition for the given system in this study.

• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2352-2354
• /
• 1999

The purpose of substation grounding system is to provide reference potential with power system and protect field workers from electrical shock resulted from unsymetrical power system faults. For this purpose, grounding grid should be designed to maintain max, touch voltage under safety criteria in fault conditions. It is difficult, however, to design a safe grounding grid at very resistive or narrow area. This paper describes an example of substation grounding grid design procedures in such areas with very severe design conditions. By using grounding conductors, which is located close to earth surface, earth surface potential could be controlled effectively, so that maximum touch voltages is to be maintained under safety criteria.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 1997.10a
• /
• pp.201-208
• /
• 1997

In most seismic codes such as the Uniform Building Code(UBC), the response modification factor(or the force reduction factor)is used to reflect the capability of a structure in dissipating energy through inelastic behavior. The response modification factor is assigned according to structural system type. Ductile systems such as special moment-resisting steel frames are assigned larger values of the response modification factor, and are consequently designed for smaller seismic design forces. Therefore, structural damage may occur during a severe earthquake. To ensure safety of the structures, the suitability of the response modification factor used in aseismic design procedures shall be evaluated. The object of this study is to develop a method for the evaluating of the response modification factor. The validity of the evaluating method has been examined for several cases of different structures and different earthquake excitations.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 1997.10a
• /
• pp.193-200
• /
• 1997

Current seismic design code is based of the assumption that the designed structures would be behaved inelastically during a severe earthquake ground motion. For this reason, seismic design forces calculated by seismic codes are much lower than the forces generated by design earthquakes which makes structures responding elastically. Present procedures for calculating seismic design forces are based on the use of elastic spectra reduced by a strength reduction factors known as "response modificaion factor". Because these factors were determined empirically, it is difficult to know how much inelastic behaviors of the structures exhibit. In this study, base shear forces required to maintain target ductility ratio were first calculated from nonlinear dynamic analysis on the single degree of freedom system. And then, base shear foeces specified in seismic design code compare with above results. If the strength(base shear) required strength should be filled by overstrength and/or redundancy. Therefore, overstrength of moment resisting frame structure will be estimated from the results of static nonlinear analysis(push-over analysis).analysis).

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1997.10a
• /
• pp.207-214
• /
• 1997

Current seismic design code is based on the assumption that the designed structures would be behaved inelastically during a severe earthquake ground motion. For this reason, seismic design forces calculated by seismic codes are much lower than the forces generated by design earthquakes which makes structures responding elastically. Present procedures for calculating seismic design forces are based on the use of elastic spectra reduced by a strength reduction factors known as "response modificaion factor". The effect of hysteretic behavior, as well as maximum ductility ratio and period on the inelastic strength demand is investigated. Special emphasis is given to the effects of the hysteretic characteristics such as strength degradation or pinching. Results indicate that inelastic strength demands are strongly dependent on level of inelastic deformation, period and hysteretic behavior.

• The Journal of Korean Medicine
• /
• v.37 no.4
• /
• pp.30-35
• /
• 2016

Objectives: The patients who had arteriosclerotic occlusive disease were treated by reperforating procedures or vessel replacing operations. We divided them by two groups. one(control group) is treated by Pletaal(cilostazole), the other(CP group) is by Pletaal with cardiotonic pills(CP). Methods : Control group was treated by Pletaal, CP group was treated by Pretaal with CP for 8 weeks. We primarily evaluated the outcomes by visual analogue scale(VAS) of pain, coldness, numbness, and edema, secondarily hematologic tests. Results : Coldness, numbness and edema were reduced at both groups. In CP group, the VAS dropped more sharply than control group, but not significant. Otherwise, there was significant reduction of VAS on pain. In hematologic tests, there were no abnormal results of all items. Conclusion : The therapy of Pletaal with CP is effective to relieve PRS specially in pain and safety on hematologic tests.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.10a
• /
• pp.507-511
• /
• 2018

This paper proposes a method for system development for high speed (300MHz) test of system IC semiconductors. The high-speed test system proposes a high-speed test circuit interface and a PCB design method for noise reduction. This paper proposes evaluation items and procedures for verifying the performance of the developed system. System IC The development of high speed test systems will help optimize the development of domestic system IC test equipment.

• Journal of Applied Reliability
• /
• v.1 no.1
• /
• pp.47-54
• /
• 2001

This paper considers the parameter estimation problem of the failure intensity function and maintenance effect in a repairable system. We propose estimation procedures for repairable systems on which preventive maintenance is performed. The failure process is modeled by a proportional age reduction model [Brown, Mahoney and Sivazlian(1983)] which is useful to model the imperfect effect of preventive maintenance. When failure and maintenance (preventive) times are given, the maximum likelihood method is used to estimate the maintenance effect and the parameters of intensity function, simultaneously We obtain the maximum likelihood estimators using a genetic algorithm. A numerical example is also presented.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.24 no.62
• /
• pp.97-109
• /
• 2001

This research is concerned with jobshop scheduling problem for an advanced manufacturing system like flexible manufacturing which consists of two machine centers and a single automated guided vehicle(AGV). The objective is to develop and evaluate heuristic scheduling procedures that minimize makespan to be included travel time of AGV. A new heuristic algorithm is proposed and illustrates the proposed algorithm. The heuristic algorithm is implemented for various cases by SLAM II. The results show that the proposed algorithm provides better solutions in reduction ratio and frequency than the previous algorithm.