• Korean Chemical Engineering Research
• /
• v.45 no.6
• /
• pp.619-626
• /
• 2007

It is of special interest in our membrane separation technology due to its low energy consumption and cost, relatively simple equipment, low investment and operation cost, et al. Full scale utilization of such processes can be widely utilized to the various fields. Using the difference of permeability of gas molecules between the filter layers, it is able to separate effectually pure gases from the mixed gases. In this paper, the membranes of PDMS, ${\gamma}-radiated$ PDMS, PTFE, PTFE-X are chosen to develop the predictive model for the separation of pure gases such as oxygen, nitrogen, hydrogen, and other gases from mixed gases. By utilizing the thermodynamic gas properties($\sigma$, $\varepsilon/k$) and experimental data of gas transport characteristics for different polymer membranes, it is able to develop the predictive model equation under the influence of temperature, pressure and polymer characteristics. Predictive model developed in this research showed good agreement with experimental data of gas permeability characteristics for develop four different polymer membranes. The proposed model can also be extended to the general equation for predicting the separation of gases based on the properties of polymeric membranes.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.11
• /
• pp.1123-1129
• /
• 2015

A pair of two-way valves typically is used in automotive washing machines, where the water flow direction is frequently reversed and highly pressurized clean water is sprayed to remove the oil and dirt remaining on machined engine and transmission blocks. Although this valve system has been widely used because of its competitive price, its application is sometimes restricted by surging effects, such as pressure ripples occurring in rapid changes in water flow caused by inaccurate valve control. As an alternative, one three-way reversing valve can replace the valve system because it provides rapid and accurate changes to the water flow direction without any precise control device. However, a cavitation effect occurs because of the complicated bottom plug shape of the valve. In this study, the cavitation index and percent of cavitation (POC) were introduced to numerically evaluate fluid flows via computational fluid dynamics (CFD) analysis. To reduce the cavitation effect generated by the bottom plug, the optimal shape design was carried out through a parametric study, in which a simple computer-aided engineering (CAE) model was applied to avoid time-consuming CFD analysis and difficulties in achieving convergence. The optimal shape design process using full factorial design of experiments (DOEs) and an artificial neural network meta-model yielded the optimal waist and tail length of the bottom plug with a POC value of less than 30%, which meets the requirement of no cavitation occurrence. The optimal waist length, tail length and POC value were found to 6.42 mm, 6.96 mm and 27%, respectively.

• Journal of Korea Technology Innovation Society
• /
• v.11 no.2
• /
• pp.264-286
• /
• 2008

In 2006, the share of energy in Korea amounted to 28% from the total import, 97% from overseas dependency, and 83% for the national Greenhouse Gas (GHG) emission in 2004. Thus, from the aspects of economical and environmental policies, an energy analysis is very important, for the industry to cope with the imminent pressure for climate change. However, the estimation of GHG gas emissions due to an energy use is still done in a primitive way, whereby each industry's usage is multiplied by coefficients recommended from international organizations in Korea. At this level, it is impossible to formulate the prevailing logic and policies in face of a new paradigm that seeks to force participation of developing countries through so called post-Kyoto Protocol. In this study, a hybrid energy input-output (E-IO) analysis is conducted on the basis of the input-output(IO) table of 2000 issued by the Bank of Korea in 2003. Furthermore, according to economic sectors, emission of the GHG relative to an energy use is characterized. The analysis is accomplished from four points of view as follows: 1) estimating the GHG emission intensity by 96 sectors, 2) measuring the contribution ratio to GHG emissions by 14 energy sources, 3) calculating the emission factor of 3 GHG compounds, and 4) estimating the total amount of national GHG emission. The total amount estimated in this study is compared with a national official statistical number. The approach could be an appropriate model for the recently spreading concept of a Life Cycle Analysis as it analyzes not only a direct GHG emission from a direct energy use but also an associated emission from an indirect use. We expect this model can provide a form for the basis of a future GHG reduction policy making.

• Korean Journal of Food Science and Technology
• /
• v.29 no.2
• /
• pp.302-308
• /
• 1997

${\beta}-Cyclodextrin\;({\beta}-CD)$ polymers were prepared using epichlorohydrin as a cross linking agent. The polymers were separated into ${\beta}-CD$ soluble polymer $({\beta}-CD\;SP)$ and ${\beta}-CD$ insoluble polymer $({\beta}-CD\;ISP)$ on a 10,000 molecular weight cut-off membrane (YM 10). Optimum separation conditions in the YM 10 were: transmembrane pressure 51.7 kPa, separation temperature $35^{\circ}C$, and volume concentration ratio 10. The flux was $0.025\;mL/cm^{2}/min$ under the optimum conditions. Gel permeation chromatography indicated that ${\beta}-CD\;SP\;and\;{\beta}-CD\;ISP$ had a degree of polymerization of $2{\sim}8$ and over 10, respectively. The formation of an inclusion complex with hydrophobic compounds such as 4-dimethylaminoazobenzene, methyl red, and naringin was compared among ${\beta}-CD,\;{\beta}-CD\;SP\;and\;{\beta}-CD\;ISP$. The molar absorptivity for the two chromatic compounds was increased and the absorption peak was shifted in the presence of ${\beta}-CD$ polymers. Naringin, the principal flavonoid bitter tasting component of citrus fruit, had a low water solubility. The solubility of naringin was increased through the formation of an inclusion complex with ${\beta}-CD$ polymers. There was no significant difference in the formation of an inclusion complex between ${\beta}-CD\;SP\;and\;{\beta}-CD\;ISP$. Reduction of the bitter components from citrus products was shown to be possible when employing ${\beta}-CD\;SP$, while the usage of ${\beta}-CD$ monomer has been limited due to the low water solubility.

• Korean Chemical Engineering Research
• /
• v.46 no.3
• /
• pp.555-560
• /
• 2008

Extraction was performed to prepare ash-free coal from low rank coal under the temperature of $200-430^{\circ}C$ and initial pressure of 0.1MPa. Three kinds of coal samples with different rank were used and N-methyl-2-pyrrolidinone(NMP, polar), 1-methyl naphthalene(I-MN, non-polar), Light Cycle Oil(LCO, non-polar) were used as solvents. Results showed that higher extraction yield could be obtained with NMP than with 1-MN and LCO, but the ash concentration shows minimun in the case of 1-MN. Three operation modes were compared, that is, idle, agitation and ultrasonic extraction mode. From the results, it was found that the extraction yield and ash concentration were 70.09% and 1.03% under the agitation mode, 80.7% and 0.76% under the ultrasonic operation mode respectively in the case of NMP used at the temperature of $350^{\circ}C$. Similar results were obtained with 1-MN. Effect of ultrasonic on the extraction was estimated as 15-20% increase in the yields and 26% reduction in the ash concentration.

• Journal of Wetlands Research
• /
• v.6 no.1
• /
• pp.149-166
• /
• 2004

Water quality and ecological environment in the Han River estuary was analyzed using the longterm water quality monitoring data from National Fisheries Research and Development Institute (NFRDI) and the existing data collected in this area. Based on the salinity distribution and changes of current direction in the lower Han River and its estuary, boundaries of the estuary were identified and also, distribution patterns of the phyto- and zooplankton, benthos, ichthyoplankton and fish were discussed related with the salinity changes in the macrotidal subestuary of Han River. Seasonal and spatial distribution of salinity suggested that the direct impact of freshwater be limited to the Incheon North Harbour all the year round and even extended to the southern area of Gyunggi Bay near Palmi island during limited time, usually in summer. Upper limit of salt water intrusion through the Han River is likely to be Singok underwater dam located Gimpo, Gyunggi Province, and normally limited to much lower part of the river, Jeonryuri, Gimpo. Biological boundaries of the Han River estuary exceeded the physical boundaries based on the salinity distribution. Many estuarine species in plankton and fish were found at the totally freshwater or saltwater depending on the seasons and tidal cycles. Some estuarine ichthyoplanktons showed extremely limited distributions in the estuary whereas adult fish revealed wide ranges of salinity adaptation. Critical environmental issues in the Han River estuary and its drainage basin are likely to be 1) pressure on development-promoted district for new town in the drainage area of the estuary, 2) reduction of tidal flat by reclamation, 3) pollutant input through river from municipal sewages and industrial wastes, and 4) ecological barrier between river and terrestrial systems by the military wire fence and riverside road.

• Applied Chemistry for Engineering
• /
• v.4 no.2
• /
• pp.365-372
• /
• 1993

$CO_2$ methanation was performed over Ni supported on cation-exchanged Y zeolites under atmospheric pressure at $250{\sim}550^{\circ}C$ and $H_2/CO_2$ mole ratio of 4. Adsorption strength between carbon dioxide and nickel was found to be Influenced by the cation exchanged in the zeolite. TPD(Temperature-programmed desorption) results show that the adsorption strength decreases in the order of Ni/NaY>Ni/MaY>Ni/HY. TPSR(Temperature-programmed surface reaction) results indicate that enhanced methanation activity is obtained when the adsorption strength between carbon dioxide and nickel is stroing. As the reduction temperature increases, the methantion activity of the catalyst increase. From this result the larger size nickel particle seems advantageous for $CO_2$ methanation reaction. The maximum activity is obtained when nickel loading is 3.3wt%. Carbon monoxide is produced as a by-product throughout the reaction temperature range, and as the contact time increases, the selectivity to methane increases and the selectivity to carbon monoxide decreases steadily. Thus methane seems to be produced from $CO_2$ via CO as an intermediate species. In the temperature range of $410{\sim}450^{\circ}C$, the methane production rate is found to be dependent on the orders of 3.3~-0.5 and 1.4~3.6 with respect to $CO_2$ and $H_2$ partial pressures, respectively. This clearly shows that $CO_2$ and $H_2$ are competing for adsorption sites and as the reaction temperature increases, it becomes increasingly difficult for $H_2$ to be adsorbed on the catalyst surface.

• Journal of the Korean Magnetics Society
• /
• v.25 no.6
• /
• pp.189-197
• /
• 2015

As enforced the regulation of fuel efficiency, the electrification of automotive components in internal combustion vehicle has been applied instead of hydraulic pressure. A typical example of such parts is the EPS (electric power steering), and it is applied to most automotive at present. In electric power steering system, the core component is motor. The reduction of cogging torque and torque ripple is required to improve steering feeling and reduce NVH (Noise Vibration Harshness) in EPS. Generally the skewed design of stator or rotor is applied in order to reduce cogging torque and torque ripple. This paper propose the design and analysis methodology of Brusheless PMSM (Permanent Magnet Synchronous Motor) which is applied to skewed stator. The proposed methodology is as follows: First Intial Design PMSM with skewed stator for EPS, Second Optimal design using RSM (Response surface method), Third Performance Analysis such as Phase Back EMF, Inductance, Load torque using FEA (Finite Element Method). Finally, the reliability of proposed design methodology will be verified through the experiments of prototype sample.

• Elastomers and Composites
• /
• v.41 no.2
• /
• pp.116-124
• /
• 2006

Cloud-point data to $160^{\circ}C$ and 1,000 bar are presented with poly(ethylene-co-15.3 mole% octene) copolymers ($PEO_{15}$) in pure 1-octene and mixtures of ethylene - 1-octene. The cloud-point curves for $PEO_{15}$ - ethylene - 1-octene mixture dramatically increase in pressure to as high as 1,000 bar with an increasing ethylene concentration. At ethylene concentrations less than 18 wt%, the ternary mixture has bubble- and cloud-point curves. As the ethylene concentration of the ternary mixture increases, the bubble-point curve and the single-phase region reduce. The reduction in the single phase region with increasing ethylene concentrations is the result of reduced dispersion interactions between $PEO_{15}$ and the mixed solvent. The single-phase region decreases with increasing temperatures when ethylene concentrations are lower than 36 wt%, whereas the single-phase region increases with temperatures at ethylene concentrations greater than 50 wt%. At ethylene concentrations greater than 50 wt% the effect of the polar interactions of the mixed solvent, which is unfavorable to dissolve PEO, is greater than the effect of the density of the mixed solvent. Therefore, the cloud-point pressures increase with a decreasing temperature. However, at ethylene concentrations less than 50 wt%, the cloud-point pressures decrease with temperature, because the effect of the polar interactions is less than the density effect.

• KSBB Journal
• /
• v.21 no.2
• /
• pp.79-84
• /
• 2006

In order to minimize the reduction of lysine productivity by accumulation of lysine and byproducts in the end of fed-batch fermentations, a salt-tolerant mutant C14-49-3-15-7-3-20, which could grow at high concentrations of NaCl was isolated through mutagenesis from the Corynebacterium glutamicum mother strain I. In the evaluation of L-lysine productivity by fed-batch fermentations using a 5 L jar fermenter, the salt-tolerant mutant strain C14-49-3-15-7-3-20 produced 130.6 g/L of L-lysine with a 48.6% of yield. The mother strain I produced L-lysine concentration only 104.9 g/L with a yield 41.8%, implying the improvement of L-lysine productivity by introduction of salt-tolerance character.