• Journal of Biosystems Engineering
• /
• v.1 no.1
• /
• pp.1-6
• /
• 1976

This paper is the third one of the study on balanced type oscillating mole-drainer, the first one was presented in No 9. Gyeongsang College Report and the second one in Vol. 17, No.4 of the KSAE. In the first part of this study, the characteristics of traction forces between the nonoscillating earth working equipments and oscillating ones was compared. A model of the balanced type oscillating mole-drainer, which composed of a mechanism that may reduce the machine vibration, was designed following the dimensional analysis and similitude technique. The model test was carried out to clarify the balancing mechanism of the oscillating parts and other parts of the machine. In the light of the results from the model tests, a prototype machine was made for experimental purpose. Results from the field test by a reported in the near future. In the second report, the model tests were carried out under the same soil conditions, i.e, . oscillating frequency, running velocity, and oscillating amplitude, etc. It was clear that use of balanced type oscillating model could substantially reduce the vibration of the whole system of the machine, when compared with the nonoscillating type model. In this paper(the third report), results of investigation on the traction force, power requirement, and moment. etc, is presented. Analysis of variance technique was used for analyzing the effect of the frequency, amplitude, and running velocity on the draft force, torque, power requirements, and moments. The results obtained from the model tests are as follows, 1) By practicing a balanced-type oscillating mole-drainer, it was possible to reduce the traction resistance by 55.1-61. 2 percent of traction resistance, however, was 1.75 - 1.95 times greater than the value of resistance which was induced by use of a mole-drainer with single bullet. The resistance of rear shank against soil was considered as a main causing factor of the above results. 2) As the oscillation frequency was increased, the traction resistance was decreased. Considering on the effect of oscillation the greater the amplitude, and the slower the running velocity was, the greater the reduction ratio of traction resistance was. 3) The ratio of the traction resistance of oscillating mole-drainer to that of non-oscillating one could be represented as a function of dimensionless variable (V/$Af$). The results from the tests were well agreed with the reported results from the experim ents on oscillation plow or hoe. 4) By taking a lower value of (V/$Af$), reducing the traction resistance was possible. This fact meant, however, that the efficiency of mole drain practice would be lower. 5) It was experimentally confirmed under the same condition of soil that the variable (R/$rD1^3$) could be represented as a function of a variable($V^2/gD$) when a non\ulcornerocillating mole-drainer was used. 6) When a oscillating mole-drainer was used, the variable(R/$rD_1^{3}$) could be represented as a function of two variables ($v^2/gD_1$) and (V^2/gD_1$). 7) The torque was not affected by a change of frequency. However, a relation of proportionality existed between torque and amplitude, running velocity, and ratio of bullet diameter. When a balanced type oscillating mole-drainer with two bullets was used, torque was increased by 52.8-78. 4 percent and total power requirement was also increased. 8) Total power requirement was increased linearly in accordance with the increasing frequency, 41.96 percent of total power was used for oscillating action. The magnitude of total power requirement was 1. 8-9. 4 times greater than that of a non-oscillating mechanism. In the view point of power requirement, it was not advisable to increase the frequency, amplitude, running velocity, and ratio of bullet diameter at the same time. 9) Only the positive moment occured in the rear shank. Change of the diameter of a rear bullet, could not affect the balancing against the soil resistance. It was necessary for rear bullet to have a large resistance against soil only when the rear bullet was in backward motion. 10) Within an extent of the experimental base, optimum limits for several design factors were A=0.5cm, $f$=22.5Hz, V=O. 05m/sec, and $\lambda$=1.0 By adapting these values traction resistance was reduced by 40 percent and vibration acceleration wa s reduced by 60 percent. Even though the total , power requirements for operating a balanced type oscillation mechanism was greater ~than that of non-oscillating one, using a oscillating mechanism would be more effective. Because a balanced type oscillating mechanism is used, tractive resistance will be reduced and then the lighter . tractive equipment could be used.

• Journal of Food Hygiene and Safety
• /
• v.33 no.3
• /
• pp.200-206
• /
• 2018

This study was to investigate the optimal condition of mixture ratio for development of functional food ingredient from Sarcodon aspratus and rice bran. First, $^{\circ}Brix$ was measured along with extraction time. Five kinds of mixtures of Sarcodon aspratus and rice bran (10:0, 7:3, 5:5, 3:7, 0:10) were extracted in $95^{\circ}C$ water over a one-hour period and the extraction yield was evaluated. We further evaluated ${\beta}-glucan$ content, DPPH radical scavenging activity, ferric ion reducing antioxidant power (FRAP), total phenolic content and total flavonoids content. As a result, both Sarcodon aspratus and rice bran showed a constant $^{\circ}Brix$ after 45 minutes of extraction time. The content of ${\beta}-glucan$ was highest in the Sarcodon aspratus and rice bran mixture with a ratio of 3:7. As the ratio of rice bran increased in all mixtures, the antioxidant capacity also increased. In conclusion, to create a functional food ingredient the optimal mixing ratio of Sarcodon aspratus to rice bran is 3:7.

• Clean Technology
• /
• v.26 no.2
• /
• pp.151-157
• /
• 2020

Rapid urbanization has elevated the risk of urban flooding due to the increase in the impervious surface, causing environmental disasters and environmental pollution problems, such as lowering the groundwater level and increasing water pollution. In Korea, low impact development (LID) techniques have been introduced to minimize these environmental impacts and maintain the water cycle soundness. However, most small-scale development projects are in blind spots because there is no legal basis for rainfall runoff management. Small-scale development projects that increase the surface runoff of rainwater are required to mandate the application of LID facilities in accordance with the polluters' responsibility principle. Therefore, it is necessary to implement a preliminary consultation system for water cycle recovery. This study focuses on the cost-benefit analysis on the application of LID techniques for small-scale development projects. The scale of nationwide small-scale development projects used for cost-benefit analysis were defined as buildings with a land area of more than 1,000 ㎡ or a total floor area of 1,500 ㎡. As a result of analyzing the cost-benefits from the installation of LID facilities, they were found to be much lower than the economic standard value of 1. This might be due to the high cost of facilities compared to the scale of the project. However, considering the overall environmental value of improving the water environment and air quality by the installation of LID facilities and the publicity of reducing the operating cost of sewage treatment facilities, the introduction of a prior consultation for small-scale development projects is inevitable. In the future, institutional and financial support from local governments is required to improve the cost-benefits with the introduction of a prior consultation for small-scale development projects.

• Journal of Korean Society of societal Security
• /
• v.4 no.2
• /
• pp.73-78
• /
• 2011

In order to resolve the problem of change in global climate which is worsening as days go by and to preemptively cope with strengthened restriction on carbon emission, the government enacted 'Framework Act on Low Carbon Green Growth' in 2010 and selected green technology and green industry as new national growth engines. For this reason, the necessity to use the un-utilized waste heat across the whole industrial system has become an issue, and studies on and applications of recycling in the agricultural and fishery fields such as cultivation of tropical crops and flatfishes by utilizing the waste heat and thermal effluent generated by large industrial complexes including power plants are being actively carried out. In this study, we looked into the domestic and overseas examples of having utilized waste heat abandoned in the form of power plant thermal effluent, and carried out economic efficiency evaluation of sturgeon aquaculture utilizing thermal effluent of Yeongwol LNG Combined Cycle Power Plant in Gangwon-do. In this analysis, we analyzed the economic efficiency of a model business plan divided into three steps, starting from a small scale in order to minimize the investment risk and financial burden, which is then gradually expanded. The business operation period was assumed to be 10 years (2012~2021), and the NVP (Net Present Value) and economic efficiency (B/C) for the operation period (10 years) were estimated for different loan size by dividing the size of external loan by stage into 80% and 40% based on the basic statistics secured through a site survey. Through the result of analysis, we can see that reducing the size of the external loan is an important factor in securing greater economic efficiency as, while the B/C is 1.79 in the case the external loan is 80% of the total investment, it is presumed to be improved to 1.81 when the loan is 40%. As the findings of this study showed that the economic efficiency of sturgeon aquaculture utilizing thermal effluent of power plant can be secured, it is presumed that regional development project items with high added value can be derived though this, and, in addition, this study will greatly contribute to reinforcement of the capability of local governments to cope with climate change.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.6
• /
• pp.406-413
• /
• 2012

Effect of three additives, chitosan, ferric chloride, and MPE50 on membrane fouling reduction was studied. They were introduced with various dosing rate into activated sludge, and changes in filtration resistance measured by the batch cell filtration test were evaluated. Both the filtration resistance and the specific cake resistance were minimized at 20 mg/g-MLSS with chitosan, 70 mg/g-MLSS with ferric chloride, and 20 mg/g-MLSS with MPE50 addition, respectively. Introduction of the additives into the activated sludge resulted in reduction of not only cake resistance, but also fouling resistance. However, the chitosan addition to three different activated sludge resulted in three different optimal dose of 10, 20, 30 mg/g-MLSS, respectively. This implies that the optimal dose is dependent on sludge characteristics rather than a constant value. Overdose above the optimal dosage always aggravated filterability in all cases. Zeta potential of sludge flocs, relative hydrophobicity, floc size distribution, soluble EPS concentration and supernatant turbidity were measured in order to analyze fouling reduction mechanism. Nearly neutral surface charge along with the largest particle size was observed at the optimal dose. This could be explained by particle destabilization and restabilization mechanism as positively charged additives were injected into sludge flocs of negative surface charge. Both soluble EPS concentration and supernatant turbidity also showed the lowest value at the optimal dose. These foulants are believed to be coagulated and entrapped in sludge flocs during flocculation. Chitosan and MPE50 which are cationic polymeric substances showed higher reduction in both soluble EPS and fine particles comparing with ferric chloride.

• Korean Business Review
• /
• v.14
• /
• pp.1-30
• /
• 2001

To prevent the VAT evasion and to form a sound VAT paying culture, we can draw the policy directions for government as follows: First, it is necessary to strengthen the tax supervision of small business and the administration of tax sources of cash-income industry. Second, the tax-deductible rate of the received tax invoices should be increased in a short-term base, and a simplified taxation system should be abolished in a long-term base. Third, in cases a trader has not received a tax invoice, an additional tax should be applied. Forth, to issue the tax invoice faster and conveniently, it is requested to introduce a new system which issues electronic card of registration when a businessman applies for his/her business registration. Fifth, to make tax standard transparent, it is desirable to punish the violator, relating to credit card regulations, stricter than present and to enforce the electronic bookkeeping. Sixth, for the reduction of noncompliance rate and creating a climate for autonomous, faithful tax return, it is necessary to expand and intensify tax investigation. And also it is necessary to make the level of penalty tax higher up and the level of criminal punishment less down, to keep up tax audit coverage. Seventh, a trader who is eligible for simplified taxation, whose tax base is under 12,000 thousand won, should not be required to pay the value added tax. But it is desirable to cut down them for the fairness of tax burden. Eighth, the effective date of the revised tax law should be fixed. Ninth, it is necessary to reinforce publicity and to educate on tax system and administration, for reducing tax evasion or tax avoidance and encouraging faithful tax return. Tenth, as the tendency of VAT evasion of distribution industry turns out to be the highest, it is requested not only to intensify tax administration on them but also to establish system and incentives, for introducing information system in distribution industry(introducing POS system, computerization of transaction record, establishing EDI between traders).

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.7
• /
• pp.1082-1090
• /
• 2005

Jocheong was prepared by adding Lentinus edodes extract to improve its quality and to give some functional properties. Contents of crude protein, ash and crude lipid were similar to those of control, while carbohydrate content was decreased. Total mineral content were $1,916.03\~2,674.24mg/kg$ that was no difference between test samples. From HPLC determination of free sugars, Jocheong was found to contain maltose as the highest sugar, followed by glucose and fructose. In amino acid analysis, seventeen amino acid were identified and quantified. Glutamic acid in Jocheong was major amino acid. The major fatty acids in Jocheong $(0\%,\;control)$ were linoleic acid, palmitic acid, oleic acid, myristic acid and caproic acid. There was no significant differences in fatty acid composition, pH and reducing sugar content among the Jocheong samples. The viscosity and solid contents tended to decrease with the addition of Lentinus edodes extract. Increasing the ratio of mushroom extract in Jocheong tended to decrease the lightness, yellowness and redness in Hunter's color value. Although sensory value decreased with increasing Lentinus edodes extracts, use of mushroom extracts (7: 3; saccharification liquids: Lentinus edodes extracts) is recommended for making Jocheong.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.43 no.3
• /
• pp.211-221
• /
• 2017

This study was performed to investigate the functional properties and characteristics of Dolnamul (Sedum sarmentosum) as a cosmetic ingredient. Lyophilized sedum powder was extracted with ethanol and stored at $-20^{\circ}C$ for the following experiments. Total polyphenol compounds of the ethanol extract of sedum (SE) was $27.98{\pm}0.34g/kg$(dry weight): epicatechin ($162.14{\pm}5.07mg/kg$), epigallocatechin ($55.99{\pm}2.49mg/kg$), and kaempferol ($47.96{\pm}3.02mg/kg$) were contained in the SE. The SE had organic radical scavenging capacity ($78.43{\pm}1.08%$) and metal reducing power (FRAP value $2.54{\pm}0.12$). FTC and TBARS assays confirmed that the SE inhibited the early stage of lipid peroxidation ($62.03{\pm}0.38%$) as well as the final stage of lipid peroxidation ($55.36{\pm}2.05%$), respectively. The SE (5 mg/mL, dry weight) was proved to have antibacterial effect on the growth of Propionibacterium acnes. The inhibitory percentages of the SE on elastase and collagenase activities were $38.94{\pm}7.09%$ and $78.94{\pm}2.49%$, respectively. Compare to the control group, the SE treated group induced an increase of Col3A1 expression and collagen production ($58.11{\pm}1.07%$). The oil in water emulsion (0.5% SE adding group) showed pH 6.88 and 1.47 g/mL of density. The hardness changes of the SE adding emulsions were not detected during the stored periods at various temperatures ($-20-45^{\circ}C$) for four weeks. It is considered that the SE has antibacterial, antioxidant, and antiaging activities.

• Food Science and Preservation
• /
• v.15 no.3
• /
• pp.461-468
• /
• 2008

To obtain basic da1a on the preparation of Cudrania tricuspidata leaves tea, the quality and anti-oxidative characteristics of dried raw leaves (RT), pan-fired leaves tea (PT) and fermented leaves tea (FT) were investigated. General characteristics of RT, PT and FT, respectively, were: moisture content 18.47, 6.23 and 8.50%; crude protein content 17.77, 20.46 and 19.13%; and carbohydrate content 54.42, 62.52 and 61.96%. The crude lipid and ash contents were in the range 0.05 - 0.07% and 9.27 -10.74% respectively; the water soluble solid content was in the order FT > PT > RT and ranged from 23.10 - 37.38%; there were no significant differences in the total polyphenol content (815.24 - 835.16 mg%). Although $L^*$ values of PT (20.94) and FT (20.85) were lower than those of RT (34.71), the $a^*$ value in PT and the $b^*$ value in FT were highest. In all ethanol extracts the reducing power, electron-donating ability and superoxide dismutase (SOD)-like activity increased in a concentration-dependent manner. Furthermore, the activity in FT was higher than in PT or RT. The total free amino-acid content was higher in FT (1429.93 mg%) than RT (1108.94 mg%) or PT (833.13 mg%). The major amino acids were L-asparagine and L-valine in RT, L-cysteine and L-glutamic acid in PT and L-proline in FT. In a sensory evaluation of PT and FT, bitter and astringent tastes were decreased relative to RT, while sweet and savory tastes, flavor, color and overall acceptability were increased. These results indicate that FT bas a higher antioxidant effect and free-amino-acid content than PT, while the sensory quality of FT is similar to that of PT.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.16 no.1
• /
• pp.27-38
• /
• 2004

In this study, the reliability design method developed by Shimosako and Takahashi in 1999 for calculation of the expected sliding distance of the caisson of a vertical breakwater is extended to take into account the variability in wave direction such as directional spreading of waves, obliquity of the deep-water design principal wave direction from the shore-normal direction, and its variation about the design value. To calculate the transformation of random directional waves, the model developed by Kweon et al. in 1997 is used instead of Goda's model, which was developed in 1975 for unidirectional random waves normally incident to a straight coast with parallel depth contours and has been used by Shimosako and Takahashi. The effects of directional spreading and the variation of deep-water principal wave directions were minor compared with those of the obliquity of the deep-water design principal wave direction from the shore-normal direction, which tends to reduce the expected sliding distance as it increases. Especially when we used the field data in a part of east coast of Korea, considering the variability in wave directions reduced the expected sliding distance to about one third of that not considering the directional variability. Reducing the significant wave height calculated at the design site by 6％ to correct the effect of wave refraction neglected in using Goda's model was found to be proper when the deep-water design principal wave direction is about 20 degrees. When it is smaller than 20 degrees, a value smaller than 6％ should be used, or vice versa. When we designed the caisson with the expected sliding distance to be 30㎝, in the area of water depth of 25 m or smaller, we could reduce the caisson width by about 30％ at the maximum compared with the deterministic design, even if we did not consider the variability in wave directions. When we used the field data in a part of east coast of Korea, considering the variability in wave directions reduced the necessary caisson width by about 10% at the maximum compared with that not considering the directional variability, and is needed a caisson width smaller than that of the deterministic design in the whole range of water depth considered (10∼30 m).