• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.816-821
• /
• 2005

The cycloid reducer has very high efficiency, high ratios, high stiffness and small size, in comparison with a conventional gear mechanism, which makes it an attractive candidate for limited space and precision application such as industrial robot. There are several publications on analysis and design of the cycloid reducer, however, it was assumed that the contact stiffness of pin rollers and cycloid disk is constant regardless of their contact geometry. Moreover, the torsional stiffness of the cycloid reducer couldn't be calculated due to the assumption. In this paper, we present a new procedure of calculating torsional stiffness of the cycloid reducer using Hertz contact theory. First, conventional force analysis of the cycloid reducer is briefly reviewed. Then, iterative numerical calculation procedure of the contact stiffness is proposed based on the Hertz contact theory where the contact stiffness depends on the contact force. In addition, total torsional stiffness of the cycloid reducer is estimated considering its rolling element bearing stiffness. The torsional stiffness of the cycloid reducer is dominated by the rolling element bearing stiffness since the contact stiffness of the cycloid disk is too large.

• Tribology and Lubricants
• /
• 제35권1호
• /
• pp.71-76
• /
• 2019

The differential planetary gear reducer as a main component of the concrete mixer driving mechanism requires a strong torque to mix concrete compounds. As this component is currently dependent on imports, it is necessary to develop it by conducting a study on vibration analysis and the resonance problem. The noise and vibration of a concrete mixer reducer increase owing to the transmission error of planetary gears, and the damage of components occurs owing to the problems in design and production. In this study, the tooth-passing frequency is calculated to evaluate the noise and vibration of a mixer reducer, and a fast Fourier transform (FFT) analysis is conducted through a vibration test using an acceleration sensor. The vibration of the reducer is measured at three points of input and output of the shaft and planetary gear housing with fixed and variable revolutions per minute. The operating conditions of gears and bearings are evaluated by performing the FFT analysis, and the resonance problem is verified. The results show that No. 1 pinion and ring gears revolve disproportionately. The amplitude values appear high, and the wear of tooth faces occur in tooth-passing frequencies and harmonic components of No. 1 and No. 2 pinion-ring gears. Therefore, we conclude that design changes in the reducer and a correction of tooth profiles are required.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.540-543
• /
• 2002

Conventional robot manipulators actuated by motors with the speed reducer such as the harmonic drive have weakness in the load capacity, since the speed reducer does not have enough strength. To overcome this, we proposed and constructed a new type of the robot actuator which is four-bar-link mechanism driven by the ball screw. We developed a new type of a revolute-jointed robot manipulator composed of four axes. The base axis is actuated with conventional speed reducer, but the others are actuated by the proposed actuators. We analyzed the mechanism of the actuators of the robot joints, and developed the dynamics model. The dynamics are expressed in the joint coordinates, and then they are mapped into the sliding coordinates of the ball screw. The structure specifications of the manipulator shown.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.697-701
• /
• 2007

In this paper, noise sources of a planocentric gear reducer are identified by experimental mehod. This study consider a reduction method of a noise/vibration about the gear, axle, bearing and others. Namely, the purpose of this study is to reduce a noise/vibration for a stability of the total system. Form the data to be measured through an experimental method, the problems of the gear, axle, bearing and others are examined closely, and the reducer is derived the model to be the engineering. The mechanism of the problem occurrence is examined through a parametric research about an each influence factor(Load). Lastly, the results of this study propose the model to be improved.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.389-390
• /
• 2006

The cycloidal reducer is one of the velocity controlling equipments in machinery. It has advantages of the higher reduction ratio, the higher accuracy, the easier adjustment of the transmission ratio and the smaller workspace than any other kinds of the reducers. This paper proposes a simple and exact approach for the lobe profile design of the two teeth difference cycloidal plate gear, which is different from the standard cycloidal reducer, by means of the principle of the instant velocity center in the general contact mechanism and the homogeneous coordinate transformation.

• 한국가스학회지
• /
• 제26권2호
• /
• pp.9-13
• /
• 2022

벨트나 체인을 이용한 감속기는 간단한 장치이긴 하지만 공간을 많이 차지하여 공간상의 제약이 있기 때문에 전동휠체어 구동부에는 부적합하다. 하지만 유성기어형태의 감속기는 동일 축에서 감속이 이루어지기 때문에 부피를 작게 할 수 있어 공간의 제약이 벨트나 체인형태의 감속기보다 덜하다. 따라서 본 연구에서는 수·전동전환이 가능한 휠체어의 구동부에 대한 연구를 통하여 유성기어형태를 이용한 감속기로 큰 추진력을 얻을 수 있는 구동부를 개발하였다. 그에 따라 감속기에 적용되는 유성기어의 치형을 Kisssoft 프로그램을 이용하여 설계를 진행하였다. 또한 기존 휠체어 바퀴에 적용 가능하도록 구동부의 설계를 진행하였고, 구동부의 수·전동 전환원리 및 작동원리에 대한 메커니즘의 최적화를 진행하였다. 연구내용을 토대로 하나의 선기어와 2개의 유성기어, 하나의 링기어를 갖는 유성기어 형태의 휠체어 감속기 구동부의 최종 설계 및 제작을 진행하였다.

• 대한기계학회논문집A
• /
• 제28권5호
• /
• pp.539-546
• /
• 2004

Conventional robot manipulators actuated by motors with the speed reducer such as the harmonic drive have weakness in the load capacity, since the speed reducer does not have enough strength. To overcome this, a new type of the robot actuator based on the four-bar-link mechanism driven by the ball screw was proposed and constructed. Also, a new type of a revolute-jointed robot manipulator composed of the developed actuators was developed. The base axis is actuated by the motor with the conventional speed reducer, but the other axes are actuated by the proposed actuators. The kinematics and dynamics of the robot were analyzed, and the performance test of the robot was made. Through the test results, the performance of superior load capacity versus the robot weight is shown.

• 대한기계학회논문집A
• /
• 제36권5호
• /
• pp.537-543
• /
• 2012

본 연구는 운전조건 하에서 감속기 내부기어의 가공정밀도와 소음의 연관 특성에 관한 실험적 연구이다. 이를 위하여 유성기어열로 이루어진 감속기를 제작하였으며, 내부 기어는 정밀도를 다르게 가공한 기어로서 4 세트를 제작하여 비교 실험하였다. 감속기에 대한 소음 및 진동 신호는 신호분석법에 의해 채집되었으며, 정지상태로부터 운전 가능 최고 속도까지 균등하게 증속하며 신호를 채집하였다. 또한 소음 레벨은 소음계를 이용하여 측정하여 비교하였다. 기어의 가공정밀도에 대한 평가는 한국 산업기술 시험원(ktl)에 의뢰하여 일본공업규격(JIS)에 준하여 객관적으로 평가되었으며, 이를 소음, 진동 신호와 함께 비교 분석하였다.

• 한국기계가공학회지
• /
• 제7권2호
• /
• pp.45-51
• /
• 2008

The objective of this study is to develop an automatic object changer unit to improve processing problems existed in the conventional horizontal machining center. In order to perform this objective, a upward and downward traverse unit in which a unit that consists of a motor and reducer, chain and sprocket wheel, and upper and lower base employed in an automatic object changer unit performs sliding contact motion in a frame was designed. To achieve this design, constraint conditions for the upward and downward traverse unit first designed. Then, an operation mechanism was designed and that was introduced as a sum of kinetic energy for the sprocket wheel and upper and lower base based on the moment of inertia, which is the kinetic energy of the converted upward and downward traverse unit in the side of the reducer. In addition, The work required to rotate the converted upward and downward traverse unit in the side of the reducer by one revolution can be calculated using the sum of work that is required in the sprocket wheel and upper and lower base that is a part of the upward and downward traverse unit. Furthermore, the converted equation of motion in the side of the motor can be introduced using the equation of motion using the converted upward and downward traverse unit in the side of the motor. Then, Then, a proper motor can be determined using predetermined specifications employed in the motor and several parameters in the upward and downward traverse unit in order to verify such predetermined specifications. Also, a design of a horizontal traverse unit that performs sliding motion on a upward and downward traverse unit and simulation that verifies the results of this design are required as a future study.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.360-366
• /
• 2001

This paper show the designing, manufacturing and performance test procedure of a high speed, fixed ratio planetary roller type traction drive as a speed reducer. The arrangement and size design for sun roller, planetary rollers and ring roller are carried out and a proper pre-load mechanism are adopted. To improve transmitting power capacity and endurance limit, nitro-carburized bearing steel and a synthetic traction oil are used. The manufactured and assembled traction drive operated successfully under unloaded conditions. Further tests for various load and speed conditions are executing now to improve the performance of the traction drive.