• Korean Journal of Materials Research
• /
• v.24 no.9
• /
• pp.443-450
• /
• 2014

Amorphous (a-Si) films were epitaxially crystallized on a very thin large-grained poly-Si seed layer by a silicide-enhanced rapid thermal annealing (SERTA) process. The poly-Si seed layer contained a small amount of nickel silicide which can enhance crystallization of the upper layer of the a-Si film at lower temperature. A 5-nm thick poly-Si seed layer was then prepared by the crystallization of an a-Si film using the vapor-induced crystallization process in a $NiCl_2$ environment. After removing surface oxide on the seed layer, a 45-nm thick a-Si film was deposited on the poly-Si seed layer by hot-wire chemical vapor deposition at $200^{\circ}C$. The epitaxial crystallization of the top a-Si layer was performed by the rapid thermal annealing (RTA) process at $730^{\circ}C$ for 5 min in Ar as an ambient atmosphere. Considering the needle-like grains as well as the crystallization temperature of the top layer as produced by the SERTA process, it was thought that the top a-Si layer was epitaxially crystallized with the help of $NiSi_2$ precipitates that originated from the poly-Si seed layer. The crystallinity of the SERTA processed poly-Si thin films was better than the other crystallization process, due to the high-temperature RTA process. The Ni concentration in the poly-Si film fabricated by the SERTA process was reduced to $1{\times}10^{18}cm^{-3}$. The maximum field-effect mobility and substrate swing of the p-channel poly-Si thin-film transistors (TFTs) using the poly-Si film prepared by the SERTA process were $85cm^2/V{\cdot}s$ and 1.23 V/decade at $V_{ds}=-3V$, respectively. The off current was little increased under reverse bias from $1.0{\times}10^{-11}$ A. Our results showed that the SERTA process is a promising technology for high quality poly-Si film, which enables the fabrication of high mobility TFTs. In addition, it is expected that poly-Si TFTs with low leakage current can be fabricated with more precise experiments.

• Journal of the Ergonomics Society of Korea
• /
• v.36 no.2
• /
• pp.145-156
• /
• 2017

Objective: This study aims to compare the usability of the adaptive touch design method with that of the height adjustable design method that are applied to the Korean QWERTY keyboard and Naratgul keyboard on smartphones, examine the results, and present practical implications. Background: Smartphone manufacturers have failed to satisfy every user with their uniform touch keyboard designs that do not consider the high use rates of keypad use. In reality, touch keyboard designing customized for every individual is impossible, but there need to be researches on was to improve usability by having touch areas changed automatically depending on user behaviors or having users adjust the keyboard height depending on their hand size. Method: As for the design methods, an object group was given smartphones with the adaptive touch design method and the other group those with the height adjustable design method. As they entered the same characters in the smartphones, typing error rates and text input speed were measured and the average values were compared. 35 individuals who would frequently use smartphones in daily life participated in the experiment. The group variable was the type of touch keyboards, and the test variables were typing error rates and text input speed, for which a T-test was implemented. Results: As for the QWERTY keyboard, the significant improvement effect was verified as the typing error rate of the adaptive touch design method was 4.21% but that of the height adjustable design method was 3.28% although there was no significant difference in terms of text input speed. As for the Naratgul keyboard, in contrast, the typing error rate of the adaptive touch design method was 2.5% while that of the height adjustable design method was 1.48%, which indicates a measure of improvement, but the effect was not significant. On the other hand, the text input speed per minute was improved as much as 22.2%, which is significant. Conclusion: First, the Korean touch keyboard usability of the adaptive touch design method and that of the height adjustable design method, when applied to Model A of Company L, showed significant difference from each other. Second, the height adjustable design method was applied to the QWERTY keyboard, the typing error rate was improved significantly. This indicates that as the keyboard height was raised, the number of buttons within the range of fingering decreased, decreasing the touch bias was reduced. Third, the height adjustable design method was applied to the Naratgul keyboard, the text input speed was improved. Application: When the QWERTY keyboard was applied to a smartphone as small as 5.5inch or less, it is highly probably that the height adjustable design method decreases the typing error rate. It may be considered to develop additional UX functions to make the keyboard font larger or give users the option to adjust button intervals in utilization of the SW advantages of the height adjustable design method.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.327-327
• /
• 2009

ZnO with a large band gap (~3.37 eV) and exciton binding energy (~60 meV), is suitable for optoelectronic applications such as ultraviolet (UV) light emitting diodes (LEDs) and detectors. However, the ZnO-based p-n homojunction is not readily available because it is difficult to fabricate reproducible p-type ZnO with high hall concentration and mobility. In order to solve this problem, there have been numerous attempts to develop p-n heterojunction LEDs with ZnO as the n-type layer. The n-ZnO/p-GaN heterostructure is a good candidate for ZnO-based heterojunction LEDs because of their similar physical properties and the reproducible availability of p-type GaN. Especially, the reduced lattice mismatch (~1.8 %) and similar crystal structure result in the advantage of acquiring high performance LED devices. In particular, a number of ZnO films show UV band-edge emission with visible deep-level emission, which is originated from point defects such as oxygen vacancy, oxygen interstitial, zinc interstitial[1]. Thus, defect-related peak positions can be controlled by variation of growth or annealing conditions. In this work, the undoped ZnO film was grown on the p-GaN:Mg film using RF magnetron sputtering method. The undoped ZnO/p-GaN:Mg heterojunctions were annealed in a horizontal tube furnace. The annealing process was performed at $800^{\circ}C$ during 30 to 90 min in air ambient to observe the variation of the defect states in the ZnO film. Photoluminescence measurements were performed in order to confirm the deep-level position of the ZnO film. As a result, the deep-level emission showed orange-red color in the as-deposited film, while the defect-related peak positions of annealed films were shifted to greenish side as increasing annealing time. Furthermore, the electrical resistivity of the ZnO film was decreased after annealing process. The I-V characteristic of the LEDs showed nonlinear and rectifying behavior. The room-temperature electroluminescence (EL) was observed under forward bias. The EL showed a weak white and strong yellowish emission colors (~575 nm) in the undoped ZnO/p-GaN:Mg heterojunctions before and after annealing process, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.12
• /
• pp.1167-1172
• /
• 2013

This paper presents a X-band doppler radar with high conversion gain using a self-oscillating-mixer(SOM) that oscillation and frequency mixing is realized at the same time. To improve phase noise of the SOM oscillator, a ${\lambda}/2$ slotted square patch resonator(SSPR) was proposed, which shows high Q-factor of 175.4 and the 50 % reduced circuit area compared to the conventional resonator. To implement the low power system, low biasing voltage of 1.7 V was supplied. To enhance the conversion gain of the SOM, bias circuit is configured near the pinch-off region of transistor, and the conversion gain was optimized. The output power of the proposed SOM was -3.16 dBm at 10.65 GHz. A high conversion gain of 9.48 dB was obtained whereas DC Power consumption is relatively low about 7.65 mW. The phase noise is -90.91 dBc/Hz at 100 kHz offset. The figure-of-merit(FOM) of the proposed SOM was measured as -181.8 dBc/Hz, which is supplier to other SOMs by more than about 7 dB.

• Journal of the Korean earth science society
• /
• v.33 no.7
• /
• pp.596-607
• /
• 2012

The R-Z relationship is one of important error factors to determine the accuracy of radar rainfall estimation. In this study, we have explored the effect of the R-Z relationships derived from disdrometer data in estimating the radar rainfall. The heavy rain event that produced flooding in St-Remi, Quebec, Canada has been occurred. We have tried to investigate the severity of rain for this event using high temporal (2.5 min) and spatial resolution ($1^{\circ}$ by 250 m) radar data obtained from the McGill S-band radar. Radar data revealed that the heavy rain cells pass directly over St-Remi while the coarse raingauge network was not sufficient to detect this rain event. The maximum 30 min (1 h) accumulation reaches about 39 (42) mm in St-Remi. During the rain event, the two disdrometers (POSS; Precipitation Occurrence Sensor System) were available: One used for the reflectivity calibration by comparing disdrometer Z and radar Z and the other for deriving disdrometric R-Z relationships. The result shows the significant improvement with the disdrometric reflectivity-dependent R-Z relationships against the climatological R-Z relationship. The bias in radar rain estimation is reduced from +12% to -2% and the root-mean squared error from 16 to 10% for daily accumulation. Using the estimated radar rainfall rate with disdrometric R-Z relationships, the flood event was well captured with proper timing and amount.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.4
• /
• pp.913-920
• /
• 2011

In this paper, a logic process based 1-kbit EEPROM IP for RFID tag chips of 900MHz is designed. The cell array of the designed 1-kbit EEPROM IP is arranged in a form of four blocks of 16 rows x 16 columns, that is in a two-dimensional arrangement of one-word EEPROM phantom cells. We can reduce the IP size by making four memory blocks share CG (control gate) and TG (tunnel gate) driver circuits. We propose a TG switch circuit to supply respective TG bias voltages according to operational modes and to keep voltages between devices within 5.5V in terms of reliability in order to share the TG driver circuit. Also, we can reduce the power consumption in the read mode by using a partial activation method to activate just one of four memory blocks. Furthermore, we can reduce the access time by making BL (bit line) switching times faster in the read mode from reduced number of cells connected to each column. We design and compare two 1-kbit EEPROM IPs, two blocks of 32 rows ${\times}$ 16 columns and four blocks of 16 rows ${\times}$ 16 columns, which use Tower's $0.18{\mu}m$ CMOS process. The four-block IP is smaller by 11.9% in the layout size and by 51% in the power consumption in the read mode than the two-block counterpart.

• Journal of Applied Biological Chemistry
• /
• v.57 no.1
• /
• pp.83-87
• /
• 2014

The effects of combined treatment of aqueous chlorine dioxide ($ClO_2$) and fumaric acid on the microbial growth in fresh-cut paprika were investigated. After the combined treatment, the populations of total aerobic bacteria and inoculated Listeria monocytogenes in the paprika sample were reduced by 0.82 and 1.21 log CFU/g, respectively, compared to those of the control. In addition, after 10 d of storage at $10^{\circ}C$, the populations were decreased by 1.21 and 2.10 log CFU/g, respectively. The predictive model for the populations of total aerobic bacteria and L. monocytogenes in the paprika was applied during storage. The prediction equation using Gompertz model was appropriate, based on the statistical analysis such as accuracy factor and bias factor. These results suggest that the combined treatment of aqueous $ClO_2$ and fumaric acid can be an effective technology for microbial decontamination and it can improve microbial safety by decreasing maximum growth rate and increasing lag time of bacteria in the fresh-cut paprika.

• Journal of Environmental Health Sciences
• /
• v.32 no.4 s.91
• /
• pp.304-315
• /
• 2006

This study is performed to reexamine the association between ambient air pollution and daily mortality in seven major cities of Korea using a method of meta-analysis with the data filed for the period 1998-2001. These cities account for half of the Korean population (about 23 million). The observed concentrations of carbon monoxide (CO, mean=1.08 ppm), ozone ($O_3$, mean=33.97 ppb), particulate matter less than 10 ${\mu}m$ ($PM_{10},\;mean=57.11\;{\mu}g/m^3$), nitrogen dioxide ($NO_2$, mean=25.09 ppb), and sulfur dioxide ($SO_2$, mean=9.14 ppb) during the study period were at levels below Korea's current ambient air quality standards. Generalized additive models were applied to allow for the highly flexible fitting of seasonal and long-term time trends in air pollution as well as nonlinear associations with weather variables, such as air temperature and relative humidity. Also, we calculated a weighted mean as a meta-analysis summary of the estimates and its standard error. In city-specific analyses, an increase of $41.17{\mu}g/m^3(IQR)\;of\;PM_{10}$ corresponded to $1{\sim}12%$ more deaths, given constant weather conditions. Like most of air pollution epidemiologic studies, this meta-analysis cannot avoid fleeing from measurement misclassification since no personal measurement was taken. However, we can expect that a measurement bias be reduced in district-specific estimate since a monitoring station is better representative of air quality of the matched district. Significant heterogeneity was found for the effect of all pollutants. The estimated relative risks from meta-like analysis increased compared to those relative risks from pooled analysis. The similar results to those from the previous studies indicated existence of health effect of air pollution at current levels in many industrialized countries, including Korea.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1203-1206
• /
• 2005

Electron temperature and plasma density in coplanar alternating-current plasma display panels (AC-PDP's) have been experimentally investigated in accordance with discharge time by a micro-probe in this experiment. The resolution of a step mortor to move in micro-Langmuir probe is 10um.[1-3] The used gas in this experiment is He-Ne-Xe (4%) mixure gas. And sustain voltage is 320V which is above of firing voltage for degradation. The electron temperature and plasma density can be obtained from current-voltage (I-V) characteristics of micro Langmuir probe, in which negative to positive bias voltage was applied to the probe. And Efficiency is calculated by formula related discharge power and light emission. Those experiments operated as various discharge time ($0{\sim}72$ Hours). As a result of this experiment, Electron Temperature was increased from 2eV to 5eV after discharge running time of 20 hours and saturates beyond 20 hours. The plasma density is inversely proportional to the square root of electron temperature. So the plasma density was decreased from $1.8{\times}10^{12}cm^{-3}$ to $8{\times}10^{11}cm^{-3}$ at above discharge running time. And the Efficiency was reduced to 70% at 60hours of discharge running time.

• Journal of Environmental Science International
• /
• v.26 no.5
• /
• pp.573-584
• /
• 2017

In order to simulate a typhoon precisely, the satellite observation data has been assimilated using WRF (Weather Research and Forecasting model) three-Dimensional Variational (3DVAR) data assimilation system. The observation data used in 3DVAR was GPS Radio Occultation (GPS-RO) data which is loaded on Low-Earth Orbit (LEO) satellite. The refractivity of Earth is deduced by temperature, pressure, and water vapor. GPS-RO data can be obtained with this refractivity when the satellite passes the limb position with respect to its original orbit. In this paper, two typhoon cases were simulated to examine the characteristics of data assimilation. One had been occurred in the Western Pacific from 16 to 25 October, 2015, and the other had affected Korean Peninsula from 22 to 29 August, 2012. In the simulation results, the typhoon track between background (BGR) and assimilation (3DV) run were significantly different when the track appeared to be rapidly change. The surface wind speed showed large difference for the long forecasting time because the GPS-RO data contained much information in the upper level, and it took a time to impact on the surface wind. Along with the modified typhoon track, the differences in the horizontal distribution of accumulated rain rate was remarkable with the range of -600~500 mm. During 7 days, we estimated the characteristics between daily assimilated simulation (3DV) and initial time assimilation (3DV_7). Because 3DV_7 demonstrated the accurate track of typhoon and its meteorological variables, the differences in two experiments have found to be insignificant. Using observed rain rate data at 79 surface observatories, the statistical analysis has been carried on for the evaluation of quantitative improvement. Although all experiments showed underestimated rain amount because of low model resolution (27 km), the reduced Mean Bias and Root-Mean-Square Error were found to be 2.92 mm and 4.53 mm, respectively.