• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.847-849
• /
• 1993

Two new schemes of three-phase rectifier using softing switching methods are introduced for the input power factor correction. These three-phase rectifiers are employed the zero voltage switching for the parallel resonant and zero current switching for the series resonant AC link type rectifiers. The dynamic modeling and discontinuous integral cycle mode control technique are also presented. With the proposed circuits and control technique, the high power factor can be obtained.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.2
• /
• pp.243-250
• /
• 2005

A new technique for improving the efficiency of single-Phase high-frequency switch-mode boost rectifiers is proposed. This rectifier includes an additional boost converter that parallels the main high-frequency switching device. The additional converter. which is controlled at lower frequencies. bypasses most of the current in the main switch and the high frequency switching loss is greatly reduced accordingly. The rectifier works cooperatively in high efficiency and as if it were a conventional rectifier with one switching device. The proposed scheme is verified by computer simulation using software PSIM.

• Journal of Power Electronics
• /
• v.19 no.1
• /
• pp.99-107
• /
• 2019

This study proposes a new modulation strategy to deal with unbalanced output voltage that is based on three-level neutral-point-clamped cascaded rectifiers. The fundament idea is to reallocate the value of the voltage levels generated by each of the modules on the basis of space vector pulse width modulation. This proposed modulation strategy can reduce the switching frequency while maintaining the mutual-module voltage balance. First, an analysis of unbalanced output voltage is reflected. Then a new modulation strategy is introduced in detail. Internal module capacitor voltages are balanced by the selection of redundant vectors. Moreover, the voltage balance ability is calculated. Finally, the feasibility of this modulation strategy is verified through experimental results.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.235-240
• /
• 1998

A procedure for the optimal design of high quality rectifiers is introduced in this paper. The procedure is capable of producing different optimal designs for the same rectifier based on the objective performance required from that rectifier. A FORTRAN-based computer system designed to solve large-scale optimization problems was used in this work to obtain the optimal designs. The optimization program uses Wolfe algorithm in conjunction with a quasi-Newton algorithm as well as a projected augmented Lagrangian algorithm to solve the highly nonlinear optimization problem. The paper also introduces a detailed analysis and an application of the procedure on a boost-type zero-current switch (ZCS) single-switch three-phase rectifier introduced recently in the literature. The obtained results are compared with popular simulation packages (i. e. PSPICE and SIMCAD) to support the validity of the proposed concept.

• Electric Engineers Magazine
• /
• v.222 no.2
• /
• pp.30-36
• /
• 2001

전회에 걸쳐서 AC 전력계통의 3상 단락전류와 1선 지락전류 및 계통접지 방식에 대하여 살펴 보았다. 본 장에서는 실제로 현장에서 사용되고 있는 Batteries, Rectifiers, DC Generators 등으로 구성되는 DC System의 제반 특성과 고장전류 계산을 쉽게 이해하도록 해설하고자 한다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.7
• /
• pp.916-922
• /
• 2014

Diode rectifiers have been widely used for an AC to DC converter. But a big problem is that they include large harmonics components in the input currents. A 12-pulse configuration with phase shifting transformer is useful for reducing them. however, it still includes the ($12{\pm}1$)th (m; integer) harmonics in the input currents. In this paper, we propose a single-phase square wave auxiliary voltage supply which is inserted in the middle DC bus. It reduces harmonics especially the 11th and 13th and the harmonic characteristic becomes almost equivalent to a 24-pulse rectifier. Theoretical analysis of the combined 12-pulse diode rectifier with the auxiliary supply is presented and a control method of the auxiliary supply is proposed. The reduction in the input current harmonics is verified by simulation using software PSIM.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.5 no.2
• /
• pp.154-162
• /
• 2000

A technique to suppress the low frequency ripple voltage of the DC output ${\gamma}$oltage in three-phase buck d diode rectifiers is presented in this paper. The proposed pulse frequency modulation method is employed to r regulate the output voltage of the buck diode rectifiers and guarantee zero-current switching of the switch over the Vvide load range. The pulse frequency control method used in tIns paper shows generally good p performance such as low THD of the input line current and unity power factor. In addition, the pulse f freιluency method can be effectively used to suppress the low frequency voltage ripple appeared in the dc output voltage. The proposed technique illustrates its validity and effectiveness through the respective s simulations and experiments.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.278-281
• /
• 2014

This paper presents the performance comparison of three types of full-wave rectifiers for vibration energy harvesting. The first rectifier is consisted of two active diodes and two MOSFETs, and the comparators of the active diodes are powered from the output of the rectifier. The second one is a 2-stage full-wave rectifier. It comprises the basic rectifier consisted of four MOSFETs and an active diode. The comparator is also powered from the output of the rectifier. The third one is an input powered rectifier. It has the same structure as the second rectifier, but the comparator is powered from the input of the rectifier. These rectifiers have been designed using a 0.35um CMOS process and their performances have been compared through simulations. In terms of efficiency, the first rectifier shows the best performance at heavy loads, but the second one is suitable at light loads. When the power consumption during absence of vibration is more important than efficiency, the input-powered rectifier is proper.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.10
• /
• pp.5116-5131
• /
• 2017

This paper studies the radio frequency to direct current (RF-DC) conversion efficiency of rectennas applicable to wireless power transfer systems, where multiple receive antennas are arranged in serial, parallel or cascaded form. To begin with, a 2.45 GHz dual-diode rectifier is designed and its equivalent linear model is applied to analyze its output voltage and current. Then, using Advanced Design System (ADS), it is shown that the rectifying efficiency is as large as 66.2% in case the input power is 15.4 dBm. On the other hand, to boost the DC output, three composite rectennas are designed by inter-connecting two dual-diode rectifiers in serial, parallel and cascade forms; and their output voltage and current are investigated using their respective equivalent linear models. Simulation and experimental results demonstrate that all composite rectennas have almost the same RF-DC conversion efficiency as the dual-diode rectifier, yet the output of voltage or current can be significantly increased; in particular, the cascade rectenna obtains the highest rectifying efficiency.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.7 no.6
• /
• pp.563-569
• /
• 2002

This paper proposes an inverter for the grid-connected photovoltaic system based on the transformer-less inverter. This system consists of a high frequency DC-DC converter, high frequency transformer, diode bridge rectifiers, a DC filter, a low frequency inverter, and an AC filter. The 20kHz switched high frequency converter is used to generate bipolar PWM pulse, and the high frequency transformer transforms its voltage twice, which is subsequently rectified by diode bridge rectifiers for a full-wave rectified 60 Hz sine wave power output. Even though the high frequency link system needs more power semiconductors, a reduced size, light weight, and saved parts cost make this system more comparative than other power conditioning systems due to elimination of 60Hz transformer.