• 한국자동차공학회논문집
• /
• 제4권1호
• /
• pp.218-228
• /
• 1996

The behaviors of the mixture at the downstream of throttle valve in a TBI type gasoline engine plays a greater role in design of intake system. A good mixture has been influencing directly not only on the engine power but also on the pollutant emission. The mixture flow in an intake manifold is very complex, and the flow characteristics are varied with the valve type, valve angle, inlet air flow rate, and the other flow factors. Three kinds of valve are chosen in this study, and the informations of the mixture flow are observed experimentally using a PIV apparatus. Perforate valve has a smaller recirculation zone than the case of solid valve with a lower valve loss coefficient, and iti is verified that the perforated valve is also suitable to control the flow rate in a mixture flow system.

• 한국산학기술학회논문지
• /
• 제19권8호
• /
• pp.8-13
• /
• 2018

질소산화물은 최근에 초미세먼지 발생에 많은 영향을 주고 있어서 대기환경 개선 측면에서 사회적으로도 크게 관심이 되고 있다. 질소산화물은 주로 화력발전 등의 연소기기에서 고온의 연소가스 분위기에서 공기 중의 질소와 산소가 반응하여 발생한다. 이에 대한 저감 방법으로 원통형 버너에 코안다 노즐을 이용한 배관으로 배기가스를 재순환하는 연소에 대한 연구가 최근에 이루어지고 있다. 본 연구에서는 코안다 노즐을 사용하여 배기가스를 재순환하는 원통형 버너의 연소가스 출구의 위치를 오른쪽으로 하는 버너(Case 1 버너), 양쪽을 출구로 하는 버너(Case 2 버너), 왼쪽을 출구로 하는 버너(Case 3 버너) 형상에 대하여 전산유체해석을 통해 연구를 수행하였으며 연소 유동의 압력, 유선, 온도, 연소 반응 속도와 질소산화물의 분포 특성을 비교 분석하였다. 연소반응은 Case 1과 Case 2버너는 연소가스 재순환 유입구가 있는 오른쪽 방향으로 일어나고 Case 3 버너는 혼합가스 유입구 부근에서 일어나고 있었다. 출구에서의 온도는 Case 2버너가 양쪽으로 배출되면서 다른 버너 보다 약 $100^{\circ}C$ 정도 온도가 낮게 나타났으며 출구에서의 NOx 농도는 Case 1버너가 다른 형상 버너 보다 약 20배 크게 나타났다. 이로부터 NOx 저감을 위해서는 배기가스 재순환 버너의 출구는 양쪽으로 배출되게 하거나 연소가스 재순환 유입구 반대 방향으로 배출 되도록 하는 것이 효과적임을 알 수 있었다.

• 청정기술
• /
• 제28권3호
• /
• pp.238-248
• /
• 2022

세계는 탄소 중립 사회로의 전환을 추진하고 있으며, 탄화수소계 연료를 수소로 대체함으로써 탄소 중립에 대한 기여를 기대할 수 있다. 하지만 수소 연소에 따른 질소산화물을 제어하기 위한 기술이 필요하며, 무화염 연소 기술이 하나의 대안이 될 수 있다. 본 연구는 수소 함량 및 배가스 재순환율에 따른 메탄-수소 연료의 연소 및 반응 특성을 분석하기 위해 Chemkin 기반의 1차원 대향류 확산화염 모델을 이용하여 해석을 수행하였다. 메탄 연소시 재순환율이 2에서 3으로 증가할 때 열방출의 흡열 구간이 없고 최대 열방출률 영역이 하나로 병합되는 무화염 연소가 달성되었다. 재순환율 3의 수소 전소 시 열방출 측면에서 무화염 연소가 달성되었으나, 화염 구조의 측면에서는 무화염 연소 달성 여부의 판단이 어렵다. 하지만 NO 생성량은 메탄 무화염 연소와 비교하여 유사한 수준으로 예측되었기에 수소 무화염 연소를 규정하기 위해서는 화염 구조, 열방출, NOx 생성에 대한 복합적인 고려가 필요하다.

• 한국분무공학회지
• /
• 제20권2호
• /
• pp.76-81
• /
• 2015

Swirl flow has an impact on the stabilization of the flame by the recirculation flow, improvement of the combustion efficiency. The swirl flow in the gun type burner is created by the spinner which is inside the airtube that guide the combustion air. Burner has generally the combustion device composed electronic spark plug, injection nozzle, combustion device adaptor, and spinner. These inner components change the air flow behavior passing through airtube. So, this study analyzed exhaust flow characteristics of the gun type burner according to the ratio of airtube diameter. Turbulence characteristics by the spinner was mean velocity, turbulence intensity, kinetic energy, shear stress and flattness factor of the air flow of axial direction and tangential direction from the exit of the airtube.

• Korea-Australia Rheology Journal
• /
• 제21권2호
• /
• pp.119-126
• /
• 2009

A numerical analysis is performed to investigate the effect of rotation on the blood flow characteristics with four different angular velocities. The artery has a cylindrical shape with 50% stenosis rate symmetrically distributed at the middle. Blood flow is considered a non-Newtonian fluid. Using the Carreau model, we apply the pulsatile velocity profile at the inlet boundary. The period of the heart beat is one second. In comparison with no-rotation case, the flow recirculation zone (FRZ) contracts and its duration is reduced in axially rotating artery. Also wall shear stress is larger after the FRZ disappears. Although the geometry of artery is axisymmetry, the spiral wave and asymmetric flow occur clearly at the small rotation rate. It is caused that the flow is influenced by the effects of the rotation and the stenosis at same time.

• 한국가시화정보학회지
• /
• 제7권1호
• /
• pp.14-20
• /
• 2009

In comparison with previous researches fur swirling flow, the spiral flow self-generated in the spiral flow nozzle has some different characteristics. It is not needed a compulsive tangential momentum to get its velocity component and has long potential core, relatively low swirl ratio, and high focusing ability. In this study, the self-generated mechanism of the spiral flow was clarified and the effect on the width of annular slit on spiral flow characteristics was investigated experimentally and numerically. As a result, the existence of tangential velocity component regardless of a compulsive angular momentum is clarified and the results obtained by experiment have a satisfactory agreement with those by numerical method, quantitatively and qualitatively.

• 한국소음진동공학회논문집
• /
• 제20권8호
• /
• pp.734-741
• /
• 2010

In this paper, an intake RCV system for low noise turbo engine was developed through optimization process of a geometric path of compressor housing and an open rate of recirculation valve. At first, the critical customer requirement from voice of customer was defined and quality function deployment of an intake RCV system was executed. And then, the renovative concept design using pugh matrix method was selected as final concept for satisfaction of requirement. Simultaneously, system analysis was carried by function diagram and fishbone diagram. Next, control factors and levels for the optimal design were performed. And, the optimal design of an intake RCV system was studied using design of experiment. Conclusively, we achieved not only cancellation tip-out noise at the driving condition but also improvement of NVH commodity through optimization process of an intake RCV system, which is optimal configuration of compressor housing and recirculation valve.

• 한국해양공학회지
• /
• 제24권4호
• /
• pp.38-46
• /
• 2010

The wall thinning phenomenon of pipes was simulated as metal loss due to erosion and corrosion. Such wall thinning defects in the pipes of power plants are a very important safety consideration. In this study, we analyzed wall thinning defects that occurred by weld bead of weld zone of boost pump recirculation pipe. From the results of the analysis of pipe failures, numerical analysis was performed by Fluent v6.3.26 using the standard k-$\varepsilon$ model of the weld bead shape, such as an elliptical or a spherical shape, on the inner wall of the pipe. Using the results obtained, we showed the overlap effect by cavitations corrosion and erosion-corrosion at the bottom of the wall-thinning defect.

• 한국미생물·생명공학회지
• /
• 제22권1호
• /
• pp.80-84
• /
• 1994

In order to induce the rapid alcohol fermentation through the increases of the cell density in a continuous alcohol fermentation of naked barley, the single-cultivation with S. cerevisiae IS-019(SCM, ordinary control), mixed-cultivation with Saccharomyces uvarum IS-026 having a flocculent ability and S. cerevisiae IS-019(MCM), and mash recirculation by single-cultivation of S. cerevisiae IS-019(MRM) modes were investigated. The cell mass in the mixed-cultivation mode was about 10% higher than that of ordinary control but the final alcohol yield was slightlyl decreased. When recycled the mash with the flow rate of 7 l/h from V$_{6}$ to V$_{5}$ fermentors under the ordinary control, the cell density was distributed at 140~170$\times $10$^{6}$ cell/ml depending upon the fermentorsorders, higher about 20% than that of the ordinary control. Under these conditions the alcohol productivity of the maximum and the overall was 12.16 g/l$\cdot $h with an alcohol of 7.6% at the V$_{5}$ fermentor and 1.19 g/l$\cdot $h with an alcohol of 8.94%, respectively. For higher cell mass it was more effective to apply the mash recirculation mode with the single-cultivation of S. cerevisiae IS-019 in a pilot scale multi-stage CSTR.

• 한국자동차공학회논문집
• /
• 제7권7호
• /
• pp.187-194
• /
• 1999

In the design of catalytic converter, velocity distribution is more important than pressure drop because monolith pressure drop is about 80% of overall pressure drop. For the catalytic converter with single diffuser, pressure drop is decreased as the angle of diffuser decrease, but when the angle is below 18$^{\circ}$, the effect is almost negligible . For the catalytic converter with double diffuser, variation of the angle of the first diffuser shows the same trend as the pressure drop while the shape of diffuser gives little influence on that The outlet shape gives negligible effect on the pressure drop and velocity . distribution . Results show that recirculation region of commercial model is aoubt 30% of the total area in the front of monolith. For the catalytic converter with Model 11 that was presented in the study, recirculation region was not detected more uniform velocity distribution was obtained, and pressure drop was also decreased.