• Journal of Korea Foundry Society
• /
• v.22 no.2
• /
• pp.89-96
• /
• 2002

This study examined the effects of adding Zn to Sn-3.5Ag solder on the microstructure changes and behavior of interface reaction of the solder joint with Cu substrate. The solder/Cu joints were examined with microscope to observe the characteristics of microstructure changes and interfacial reaction layer with aging treatment for up to 120 days at $150^{\circ}C$. Results of the microstructure changes showed that the microstructures were coarsened with aging treatment, while adding 1%Zn suppresses coarsening microstructures. The Sn-3.5Ag/Cu had a fast growth rate of the reaction layer in comparison with the Sn-3.5Ag-1Zn at the aging temperature of $150^{\circ}C$. Through the SEM/EDS analysis of solder joint, it was proved that intermetallic layer was $Cu_6Sn_5$ phase and aged specimens showed that intermetallic layer grew in proportion to $t^{1/2}$, and the precipitate of $Ag_3Sn$ occur to both inner layer and interface of layer and solder. In case of Zn-containing composite solder, $Cu_6Sn_5$ phase formed at the side of substrate and Cu-Zn-Sn phase formed at the other side in double layer. It seems that Cu-Zn-Sn phase formed at solder side did a roll of banrier to suppress the growth of the $Cu_6Sn_5$ layer during the aging treatment.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.515-518
• /
• 1997

Resident time of the centrifugal extractor for organic phase extraction using a height controlled separator weir and a divert plate is the important factor that affects significantly the chemical material extraction and the productivity in the chemical and mechanical processes. In this paper, it describes the design of the device for extraction of an organic phase from radioactive wastes, and considers phase separating weir and divert disk, both being designed to be adjustable in their positions, for effectively separating an organic phase. A height-adjustable separating weir unit used for separating the organic phase from the aqueous phase using a phase separating weir and designed to control the height of the separating weir as desired so as to allow the weir to be positioned at a boundary layer between two separated phases. The centrifugal extractor controls satisfactorily the mixed reaction time of two phases within the separator regardless of the variations of the mixing ratio of the two phases and the rotating speed of the extractor, is designed to be adjustable in its position in the vertical direction, thus allowing the user to appropriately select the mixed reaction time of the two phases within the extractor as desired. From development of a centrifugal extractor, it can effectively recover such usable elements, and preferably reducing the output quantity of radioactive wastes.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.10
• /
• pp.2877-2883
• /
• 2010

The folding kinetics of $WT^*$ ubiquitin variant with valine to alanine mutation at sequence position 26 (HubWA) was studied by stopped-flow fluorescence spectroscopy. While unfolding kinetics showed a single exponential phase, refolding reaction showed three exponential phases. The semi-logarithmic plot of urea concentration vs. rate constant for the first phase showed v-shape pattern while the second phase showed v-shape with roll-over effect at low urea concentration. The rate constant and the amplitude of the third phase were constant throughout the urea concentrations, suggesting that this phase represents parallel process due to the configurational isomerization. Interestingly, the first and second phases appeared to be coupled since the amplitude of the second phase increased at the expense of the amplitude of the first phase in increasing urea concentrations. This observation together with the roll-over effect in the second folding phase indicates the presence of intermediate state during the folding reaction of HubWA. Quantitative analysis of Hub-WA folding kinetics indicated that this intermediate state is on the folding pathway. Folding kinetics measurement of a mutant HubWA with hydrophobic core residue mutation, Val to Ala at residue position 17, suggested that the intermediate state has significant amount of native interactions, supporting the interpretation that the intermediate is on the folding pathway. It is considered that HubWA is a useful model protein to study the contribution of residues to protein folding process using folding kinetics measurements in conjunction with protein engineering.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.11
• /
• pp.1049-1054
• /
• 1998

The LiCo$O_2$ powder was synthesized by a solution phase reaction. This shows a high (003) peak intensity and low (104) or (101) peak intensities in X-ray diffraction spectra. The LiCo$O_2$/Li cell shows an initial discharge capacity of 102.9mAh/g and an average discharge potential or 3.877V at a current density of 50mA/g between 3.0~4.2V. The peaks of dQ/dV plot are associated with Li ion intercalation/deintercalation reaction. To evaluate the cycleability of an actual battery system, cylindrical lithium ion cell was manufactured using graphitized MPCF anode and LiCoO$_2$ cathode. After 100th cycle, this cel maintains 80% capacity of 10th cycle value. The LiCoO$_2$/MPCF cell has a high discharge voltage of 3.6~3.7V and a good cycle life performance on cycling between 4.2~2.7V.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.2
• /
• pp.292-300
• /
• 1997

PSZT powders having the particle size of 0.5~5 $\mu\textrm{m}$ with cubic shapes, were prepared by a hydrothermal reaction in the temperature range of 150~$^{\190circ}C$ for a 2 h reaction. Experimental results showed that as the reaction temperature increased, the nucleation and crystal growth were accelerated and the the particle size became larger. However, the particle size became smaller with its narrow distribution as the concentration of a mineralizer (KOH) increased. It was possible to reduce the reaction temperature by increasing mineralizer concentrations. With increase in Zr/Ti ratio, the major crystal phase of synthetic PSZT powders was seen to change from tetragonal phase to rhombohedral phase.

• Journal of the Korean Ceramic Society
• /
• v.23 no.1
• /
• pp.33-43
• /
• 1986

The synthesis of high-purity AlN by a vapor-phase reaction was investigated using the $NH_3-AlCl_3-H_2$ reacting system. The theoretical yields of AlN were determined from th thermodynamic equilibrium composi-tions. It was shown that the yields above 90% could by obtained even in the range of relatively low temper-ature of 600-1200K. The reaction temperature and the initial amounts/ratios of the reacting gases showed significant effects on the yields but the total pressure did not. The experimental results showed that a high-purity AlN having a needle shape was the only product as a solid phase and its amount produced increased with the reaction temperature. While the degree of agglmera-tion of the synthesized AlN increased with the reaction temperature the size of each particle consisting of the agglomerates was independent of the temperature but grew from 0.09 to 0.115${\mu}{\textrm}{m}$ with the flow rate of NH3. These experimental results were compared with the theoretical aspects for the synthesis of a high-purity AlN.

• Journal of Powder Materials
• /
• v.20 no.3
• /
• pp.221-227
• /
• 2013

$TiB_2$-reinforced iron matrix composite (Fe-$TiB_2$) powder was in-situ fabricated from titanium hydride ($TiH_2$) and iron boride (FeB) powders by the mechanical activation and a subsequent reaction. Phase formation of the composite powder was identified by X-ray diffraction (XRD). The morphology and phase composition were observed and measured by field emission-scanning electron microscopy (FE-SEM) and energy-dispersive X-ray spectroscopy (EDS), respectively. The results showed that $TiB_2$ particles formed in nanoscale were uniformly distributed in Fe matrix. $Fe_2B$ phase existed due to an incomplete reaction of Ti and FeB. Effect of milling process and synthesis temperature on the formation of composite were discussed.

• Journal of the Korean Ceramic Society
• /
• v.33 no.8
• /
• pp.921-927
• /
• 1996

The liquid-phase concentration from the interior to the surface region and its influence on the microstructural changes were investigated in pressureless sintered $\beta$-SiC Surface reaction-layer was formed by reaction of packing powder and volatile components on the surface during sintering which was induced the concentration of liquid-phase in the surface regions. The microstructural changes between the surface region and the interior were appeared in sintered specimen which was resulted from the difference of liquid-phase content during sintering. Microstructural changes were observd with the depth of about 250${\mu}{\textrm}{m}$ from he surface. The grain size and aspect ratio of SiC in the interior are larger than those in the surface region and the rate of transforma-tion of $\beta$-to $\alpha$-SiC during sintering is higher in the interior than that in the surface region.

• Journal of the Korean Ceramic Society
• /
• v.33 no.12
• /
• pp.1421-1425
• /
• 1996

Sintered Si3N4 and Inconel composed of Ni(58-63%) Cr(21-25%) Al(1-17%) Mn(<1%) fe(balance) were pressurelessly joined by using Ag-Cu-Ti brazing filler metal at 950℃ and 1200℃ under N2 gas atmosphere of 1atm and their interfacial structures were investigated. In case that the reaction temperature was low as 950℃ its interfacial structure was "Inconel metal/Ti-rich phase layer/brazing filler metal layer/Si3N4 " Ti used as reactive metal existed in between inconel steel and brazing metal and moved to the interface of between brazing filler metal nd Si3N4 according as reaction temperature increased up to 1200℃. The interfacial structure of inconel steel-Si3N4 reacted at 1200℃ was ' inconel metal/Ni-rich phase layer containing of Fe. Cr and Si/Cu-rich phase layer containing of Mn and Si/Si3N4 " Cr Mn, Ni and Fe diffused to the interface of between brazing filler metal and Si3N4 and reacted with Si3N4 The most reactive components of ingredients of inconel metal were Cr and Mn. On the other hand Ti added as reactive components to Ag-Cu eutectic segregated into Ni-rich phase layer,.

• Journal of the Korean Ceramic Society
• /
• v.35 no.5
• /
• pp.458-464
• /
• 1998

Variations of reaction sequence of $Pb(Zn_{0.6}Mg_{0.4})_{1/3}Nb_{2/3}O_3$[PZMN] with precusor mixing methods were ex-amined using X-ray diffraction and dielectric characteristics. In the present study three different types of precursor mixing methods (oxide mixing PbO+$ZnNb_2O_6+MgNb_2O_6$[Zn+MN] and PbO+(Zn,Mg)$Nb_2O_6$[ZMN] precursor mixing) were adopted. When the oxide mixing method was used for the PZMN synthesis a Zn-rich perovskite phase and pyrochlore phase were formed. Compared with PbO+ZN+MN precursor mixing method the PbO-ZMN precursor led to a lowering of the formation temperature for perovskite sin-gle phase. These variation of composition and formation temperature of the perovskite phase were dis-cussed in terms of the difference in the solid-reaction requence between these three different types of pre-cursor mixing.