• 대한기계학회논문집B
• /
• 제35권12호
• /
• pp.1391-1398
• /
• 2011

반동도에 따른 증기터빈의 설계 및 성능 해석을 컴퓨터 시뮬레이션으로 수행하였다. 깃 각도와 출구면적, 노즐면적과 같은 설계변수들과 터빈동력, 선도효율, 축방향 추력과 같은 성능변수들을 반동도에 따라 나타내었다. 추가적인 설계 및 성능변수에 대한 정보를 제공하기 위하여, 깃 각도와 터빈동력, 선도효율, 축방향 추력과 같은 주된 설계 및 성능변수들을 유동계수(주속도에 대한 축방향속도)의 함수로 제시하였다. 터빈동력, 선도효율을 최대로 하는 반동도 및 유동계수가 존재함이 밝혀졌으며, 반동도가 증가함에 따라 동익의 깃 형상은 대칭형으로부터 많이 벗어남을 보여주었다.

• Advances in concrete construction
• /
• 제3권1호
• /
• pp.71-90
• /
• 2015

In order to investigate the feasibility and advantage of tuff used as pozzolan in cement-based composite, the representative specimens of tuff were collected, and their chemical compositions, proportion of vitreous phase, mineral species, and rock structure were measured by chemical composition analysis, petrographic analysis, and XRD. Pozzolanic activity strength index of tuff was tested by the ratio of the compression strength of the tuff/cement mortar to that of a control cement mortar. Pozzolanic reaction degree, and the contents of CH and bond water in the tuff/cement paste were determined by selective hydrochloric acid dissolution, and DSC-TG, respectively. The tuffs were demonstrated to be qualified supplementary binding material in cement-based composite according to relevant standards. The tuffs possessed abundant $SiO_2+Al_2O_3$ on chemical composition and plentiful content of amorphous phase on rock texture. The pozzolanic reaction degrees of the tuffs in the tuff/cement pastes were gradually increased with prolongation of curing time. The consistency of CH consumption and pozzolanic reaction degree was revealed. Variation of the pozzolanic reaction degree was enhanced with the bond water content and relationship between them appeared to satisfy an approximating linear law. The fitting linear regression equation can be applied to mutual conversion between pozzolanic reaction degree and bond water content.

• 펄프종이기술
• /
• 제35권1호
• /
• pp.41-47
• /
• 2003

Recently, interest in utilization plan of recycling paper have been enhanced. Therefore, this research aimed to develop the manufacture process of cellulose acetate using old newsprint by acetosolv pulping process. And the manufactured cellulose acetate was also analyzed, especially based on chemical properties. The summarized results in this research were as follows; Reaction time, kind and amount of catalyst, and ratio of liquor to material were varied during acetosolv pulping process of old newsprint. Ratio of liquor to material did not give the significant difference in reaction product. Delignification rate was increased with increasing reaction time during acetosolv pulping, but yield and degree of substitution decreased with increasing reaction time. Sulfuric acid are better catalyst than hydrochloric acid in acetosolv pulping process for old newsprint, and optimal addition amount of catalyst was 1% based on reaction material. Delignification, yield, and degree of substitution were influenced by the catalyst and reaction time. Under pulping condition of $120^{\circ}C$ in 1/12 liquor to material ratio and 60min, degree of substitution was about 0.7. The acetylation reaction was not completely caused by these reaction condition. The examination of the FT-IR spectra revealed that absorption band(1200$\textrm{cm}^{-2}$, 1,750$\textrm{cm}^{-1}$) caused by carbonyl group were confirmed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.32-36
• /
• 2001

Recently, reaction injection molding has been used broadly for rapid prototyping, because of its convenience and versatility. Since the properties of molded products are dependent on the process variables and the production is very short(less than 2minutes), the control of process variables is important. Generally, the two significant process variables are degree of cure and temperature of the reactants. In this paper, the relation between the degree of cure and the temperature of reactants was investigated to find the optimal curing condition of reaction injection molding for rapid prototyping. The degree of cure during reaction injection molding was measured by the Lacomtech sensor and dielectrometry equipment employing Wheatstone bridge type circuit.

• 한국미생물·생명공학회지
• /
• 제23권4호
• /
• pp.416-424
• /
• 1995

Mechanism of the cyclodextrin (CD) production reaction by cyclodextrin glucanotransferase (CGTase) using swollen extrusion starch as substrate was investigated emphasizing the structural features of starch granule. The degree of gelatinization was identified to be the most representative structural characteristic of swollen starch. The most suitable degree of gelatinization of swollen starch for CD production was around 63.52%. The structural transformation of starch granule during enzyme reaction was also followed by measuring the changes of the degree of gelatinization, microcrystallinity, and accessible and inaccessible portion to CGTase action of residual swollen starch. The adsorption phenomenon of CGTase to swollen starch was also examined under various conditions. The inhibition mechanism of CGTase by various CDs was identified to be competitive, most severely by a-CD. The mechanism elucidated will be used for development of a kinetic model describes CD production reaction in heterogeneous enzyme reaction system utilizing swollen extrusion starch.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표대회 논문집(III)
• /
• pp.883-887
• /
• 1998

Hydration is the main reason for the growth of the material properties. A exact parameter to control the chemical and physical process is not the time, but the degree of hydration. Therefore, it is reasonable that development all material properties should be formulated in terms of degree of hydration. Mathematical formulation of degree of hydration is based on combination of reaction rate functions. The effect of moisture conditions as well as temperature on the rate of reaction is considered in the degree of hydration model. This effect is subdivided into two contributions: water shortage and water distribution. The former is associated with the effect of on the progress of hydration. The water needed for progress of hydration do not exist and there is not enough space for the reaction products to form. The latter is associated with the effect of free capillary water distribution in the pore system. Physically absorption layer does not contribute to progress of hydration and only free water is available for further hydration.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 추계 학술논문 발표대회
• /
• pp.13-14
• /
• 2014

Ultra high performance concrete (UHPC) consists of cement, silica fume (SF), sand, fibers, water and superplasticizer. Typical water/binder-ratios are 0.15-0.20 with 20-30% of silica fume. The development off properties of hardening UHPC relates with both hydration of cement and pozzolanic reaction of silicafume. In this paper, by considering the production of calcium hydroxide in cement hydration and its consumption in the pozzolanic reaction, a numerical model is proposed to simulate the hydration of UHPC. The degree of hydration of cement and degree of reaction of silica fume are obtained as accompanied results from the proposed hydration model. The properties of hardening UHPC, such as degree of hydration of cement, calcium hydroxide contents, and compressive strength, are predicted from the contribution of cement hydration and pozzolanic reaction. The proposed model is verified through experimental data on concrete with different water-to-binder ratios and silica fume substitution ratios.

• 폴리머
• /
• 제26권3호
• /
• pp.287-292
• /
• 2002

산소분위기에서 전자선을 조사하여 과산화물을 생성시킨 폴리프로필렌에 benzoyl peroxide (BPO)를 개시제로 사용하여 비닐계 단량체인 스티렌과 glycidyl methacrylate (GMA)를 기상 그라프트 반응시켰다. 합성체의 그라프트율은 반응온도가 증가함에 따라 증가하는 경향을 나타내었고, 단량체가 스티렌의 경우 $70^{\circ}C$에서 최대였으며, GMA의 경우 반응온도 $80^{\circ}C$에서 최대로 나타났다. 반응시간에 따른 최대 그라프트율은 스티렌이 GMA보다 높게 나타났다 단량체 내 증류수의 조성에 따른 그라프트율은 사용되어지는 단량체의 비등점에 영향을 받는 것으로 나타났다.

• 한국전기전자재료학회논문지
• /
• 제17권9호
• /
• pp.967-972
• /
• 2004

Hardness and surface property of coated gel materials are considerably different according to kinds(particle size/stabilized ion) of colloidal silica(CS), kinds of silanes, content ratio of silane versus CS, and reaction degree in sol solution. We report the properties of sol-gel coating materials in which the factors of reaction are kinds of CS, contents ratio of CS and MTMS, and reaction time of sol. The contact angles of the coated films obtained from the mixed CS system showed a little good relationship with MTMS content increase to those from HSA CS reaction system and the change of contact angle didn't have much effect on reaction time of sol. In the coating films obtained from HSA CS reaction system, the surface was much rough in case of that the content MTMS decreased and the reaction of sol kept long. The surface roughness of films obtained from the mixed CS reaction system showed similar tendency, though its degree was a little different. In synthesis of sol-gel coating materials, we could identify that choice of CS kinds and content ratio of CS and silane were important and it was desirable the reaction time of sol is not long.

• 멤브레인
• /
• 제15권4호
• /
• pp.281-288
• /
• 2005

생체 적합성이 우수한 히아루론산과 생분해성이 우수한 폴리 락타이드의 이량체를 결합하여 약물 방출 시스템에 적용할 수 있는 생체 재료를 제조하고자 하였다. 냉동 건조법을 이용하여 히아루론산과 락타이드를 가교제 1-ethyl-3-(3-dimethyl aminopropyl) carbodiimide (EDC)로 가교시켰다. 생성된 막을 핵자기 공명 분광법으로 분석하여 락타이드 반응도와 EDC 반응도를 결정하였다. 히아루론산에 대한 락타이드 몰비, 가교제 농도가 증가할수록 혹은 가교 온도가 감소할수록, 락타이드 반응도가 증가하였으며 팽윤도는 감소하였다. 서로 다른 락타이드 반응도를 가진 막으로 약물 방출 실험을 수행한 결과 락타이드 반응도가 증가하면 약물 방출 속도가 감소하는 경향을 보였다. 또 친수성이 다른 여러 가지 약물로 약물 방출 실험을 수행한 결과 친수성이 우수한 약물일수록 서서히 방출되었다.