• 전기의세계
• /
• v.28 no.9
• /
• pp.51-59
• /
• 1979

The forming and design method of D.C thyristor chopper circuit for DC Series motor control is suggested, ard the computation method of thyristor commutaing element's, value which makes it all the more important, is possible. Also the trigger circuit was dealt with. In this paper, in order to control the duty cycle, the duty time is kept on constancy and variable chopping frequency was adopted. By above mentioned circuit design method, the D.C thyristor chopper circuit was implemented and tested. In this circuit, the result of D.C motor control was good and reliable. The relation between the $K_{d}$ and the ratio of input-output current, or the characteristic of speed was varied lineary at the range 0.1 ~ 0.9 of duty cycle. This confirms the fact that D.C to D.C power conversion which is the merit of chopper control is operated most likely a transformer.ormer.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.11a
• /
• pp.251-255
• /
• 2005

This paper proposes a new soft switching technique for a phase-shift controlled bi-directional DC-DC converter. The described converter employs a low profile high frequency transformer and two active full-bridge converters for bidirectional power flow capability. A new soft switching technique is proposed, which guarantees soft switching over wide range (no load to full load) without any additional circuit components. In the proposed switching scheme, the switch pairs in the diagonal position of the converter each are turned on/off simultaneously by the switching signals with a variable duty ratio depending on the phase shift amount, and the converter is operated without freewheeling interval.

• Journal of Power Electronics
• /
• v.6 no.3
• /
• pp.205-213
• /
• 2006

A cost-effective magnetic-coupled AC-PDP sustain driver with low switching loss is proposed. The transformer reduces current stress in the energy recovery switches which affects circuit cost and reliability. The turns-ratio can be used to adjust the sustain pulse slopes which affect gas discharge uniformity. Dividing the recovery paths prevents abrupt changes in the output capacitance and thereby switching losses of the recovery switches is reduced. In addition, the proposed circuit has a more simple structure because it does not use the recovery path diodes which also afford a large recovery current. By reducing the current stress and device count in the energy recovery circuit, the proposed driver may have decreased circuit cost and improved circuit reliability.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.205-207
• /
• 2007

Position information is very important when driving the Permanent Magnet Synchronous Motor(PMSM). Generally, resolver is used to obtain exact position information. However, it generates periodic position errors due to the transformer ratio difference and excitation signal distortion. When the vector control is done with the position information that includes position error, torque ripple is periodically generated. This paper proposes the solution through analysis of above problem. Also, it’s validity is verified by simulation and experiment.

• Proceedings of the KIEE Conference
• /
• 2004.05b
• /
• pp.180-182
• /
• 2004

We have investigated characteristics of varnish and oil impregnant. When transformers are manufactured with some moisture and varnish impregnant not entirely dried, those should be caused by factors that deteriorate the electrical or mechanical property after installation. Therefore, in this study we experienced moisture content of the new insulating paper and the varnish impregnant paper in the ratio of time for confirming factors that deteriorate the paper characteristics. Besides, we investigated a property study that was experienced the value of dielectric strength and tensile strength as no serviced insulating samples of transformer.

• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.143-145
• /
• 1996

This paper presents the hybrid type based expert system for fault diagnosis in transformers. The proposed system uses the novel fault diagnostic technique based on dissolved gas analysis(DGA) in oil-immersed transformers. The uncertainty of key gas analysis, norm threshold, and gas ratio boundaries are managed by using a fuzzy set. Also, the uncertainty of the fault diagnostic rules are handled by using fuzzy measures. Finally, kohnen's feature map performs fault classification in transformers. To verify the effectiveness of the proposed diagnosis technique, the hybrid type based expert system for fault diagnosis has been tested by using KEPCO's transformer gas records.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.8
• /
• pp.70-75
• /
• 2015

High Step-up DC-DC Converters have been demanded for renewable energy applications. Transformer or coupled inductor is generally used to boost output voltage of converters. This methods can relatively obtain high voltage than others, whereas have heavy weight and high cost. To complement these disadvantages, we studied transformerless high step-up DC-DC converter. In various transformerless topologies, Boost converters combined with Cockcroft-Walton have studied. In this paper, we proposed a symmetrical Cockcroft-Walton circuit for transformerless high step-up DC-DC converter. Finally, we simulated proposed converter to compare with existing converter. As a result, proposed converter has higher duty ratio or lower cost than existing transformerless converters which are discussed in this paper.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.429-430
• /
• 2012

본 논문에서는 LED 구동용 전원장치의 필터커패시터와 변압기 권선비에 따른 MOSFET의 전압 정격 및 스위칭 손실 특성 등을 다루었다. 스위칭 손실을 최소화 하려면 변압기 권선비를 최적화할 필요가 있다. 또한 필터커패시터 값이 MOSFET의 전압정격에 영향을 미치므로 이를 고려한 설계가 필요함을 확인하였다.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.19-20
• /
• 2012

본 논문은 마이크로그리드에서 에너지 저장 시스템으로 이용되는 슈퍼커패시터 충방전용 양방향 DC-DC 컨버터의 효율을 고려한 변압기 권선비 설계에 관한 것이다. 본 논문에서 다루고자 하는 시스템은 Dual Full-Bridge 방식의 양방향 DC-DC 컨버터이다. 슈퍼커패시터측의 방전 동작시 컨버터는 부스트 컨버터로 등가화 할 수 있다. 따라서 등가화한 부스트 컨버터에 대해 권선비를 달리하면서 동일한 출력 조건에서 스위치 손실을 계산하였으며, 이를 통하여 최소의 손실을 가지는 출력전압 즉, 권선비를 찾는 방법을 제안한다.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.518-519
• /
• 2012

This paper suggested a fuel cell generation system which combined interleaved full-bridge converter with half-bridge inverter. High ratio step-up converter is essential to use the power as general voltage source. Full-bridge converter has high efficiency and can boost the input voltage to high output with transformer. With series connected capacitors, interleaved full-bridge converter and half-bridge inverter are combined. Half-bridge inverter has two fewer switches compared to full-bridge type. Also, switching loss can be reduced. The performance is verified through simulation with 1.5[kW] fuel cell generation system.