• Resources Recycling
• /
• v.22 no.6
• /
• pp.73-80
• /
• 2013

Marine mineral resources are classified into submarine and seawater mineral resources. In seawater, huge amounts of useful minerals, such as uranium, lithium, magnesium, aluminum, zinc, iron, silver, copper, vanadium, nickel, titanium and cobalt are present. If the rare metals recovery technology from seawater is developed, the commercialization of the precess will be possible. For the 21st century, countries rich in resoures tend to weaponize the resources, according to the depletion of reserves and quality degradation of metal resources in the land. Therefore, Korea that relies on imports for most of the metal resources, should focus on the research and development of the rare metals recovery technology from seawater by using the geographical characteristics of the country that is on three sea-sides.

• Journal of Korea Foundry Society
• /
• v.26 no.4
• /
• pp.174-179
• /
• 2006

This study aims to investigate the microstructures and mechanical properties of DCI manufactured by sand and metal mold casting. To prohibit the formation of the chill, carbon, silicon and rare earth($0{\sim}0.2\;wt%$) were controlled and temperature of metal mold was constantly kept at $160^{\circ}C$. The sizes, counts and nodularity ratios of nodules were analyzed by image analysis device. Wear test using pin-on-disc wear tester was carried out under the conditions of load 47.2N, velocity 0.4 m/s and distance 2000 m. Tensile test using Instron type testing machine was performed with velocity of 0.1 mm/min according to the KS B 0802. The formation of the chill was not observed when percentage of the carbon and silicon were 3.8 and 2.5. Mechanical properties of GCD manufactured by metal mold were better than sand casting.

• Mineral and Industry
• /
• v.28
• /
• pp.45-54
• /
• 2015

• Mineral and Industry
• /
• v.28
• /
• pp.23-37
• /
• 2015

• Mineral and Industry
• /
• v.28
• /
• pp.38-44
• /
• 2015

• Mineral and Industry
• /
• v.28
• /
• pp.55-66
• /
• 2015

• Journal of Korea Foundry Society
• /
• v.28 no.2
• /
• pp.57-63
• /
• 2008

• Resources Recycling
• /
• v.31 no.1
• /
• pp.12-20
• /
• 2022

The smelting reduction of spent lithium-ion batteries results in metallic alloys containing Co, Cu, Fe, Mn, Ni, and Si. A process to separate metal ions from the sulfuric acid leaching solution of these metallic alloys has been reported. In this process, ionic liquids are employed to separate Fe(III) and Cu(II). In this study, D2EHPA and Cyanex 301 were employed to replace these ionic liquids. Fe(III) and Cu(II) from the sulfate solution were sequentially extracted using 0.5 M D2EHPA with three stages of cross-current and 0.3 M Cyanex 301. The stripping of Fe(III) and Cu(II) from the loaded phases was performed using 50% (v/v) and 60% (v/v) aqua regia solutions, respectively. The mass balance results from this process indicated that the recovery and purity percentages of the metals were greater than 99%.

• Resources Recycling
• /
• v.31 no.3
• /
• pp.73-80
• /
• 2022

Reduction smelting of spent lithium-ion batteries at high temperature produces metallic alloys. Following solvent extraction of the leaching solutions of these metallic alloys with either sulfuric or hydrochloric acid, the raffinate is found to contain Ni(II), Co(II), Mn(II), and Si(IV). In this study, two cationic exchange resins (Diphonix and P204) were employed to investigate the loading behavior of these ions from synthetic sulfate and chloride solutions. Experimental results showed that Ni(II), Co(II), and Mn(II) could be selectively loaded onto the Diphonix resin from a sulfate solution of pH 3.0. With a chloride solution of pH 6.0, Mn(II) was selectively loaded onto the P204 resin, leaving Ni(II) and Si(IV) in the effluent. Elution experiments with H₂SO₄ and/or HCl resulted in the complete recovery of metal ions from the loaded resin.

• Macromolecular Research
• /
• v.17 no.8
• /
• pp.563-567
• /
• 2009

In order to improve the thermomechanical performance of polyketone, a third monomer (4-methylstyrene) was added to the copolymerization system. The terpolymer of CO, styrene, and 4-methylstyrene was synthesized in the presence of multi component catalysts containing palladium acetate and rare earth metal phosphonates. The products were characterized by infrared spectroscopy (IR), and nuclear magnetic resonance spectroscopy (NMR). The effects of the different components, including the third monomer, palladium acetate, 2,2'-bipyridyl, rare earth phosphonate, p-toluene-sulphonic acid, and p-benzoquinone, were also studied. The highest catalytic activity of 965.51 g/(gPd h) was obtained with a catalyst containing palladium acetate and rare earth phosphonate.