• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.376-376
• /
• 2012

Semiconductor nanowires (NWs) are future building block for nano-scale devices. Especially, Ge NWs are fascinated material due to the high electrical conductivity with high carrier mobility. It is strong candidate material for post-CMOS technology. However, thermal stability of Ge NWs are poor than conventional semiconductor material such as Si. Especially, when it reduced size as small as nano-scale it will be melted around CMOS process temperature due to the melting point depression. Recently, Graphene have been intensively interested since it has high carrier mobility with single atomic thickness. In addition, it is chemically very stable due to the $sp^2$ hybridization. Graphene films shows good protecting layer for oxidation resistance and corrosion resistance of metal surface using its chemical properties. Recently, we successfully demonstrated CVD growth of monolayer graphene using Ge catalyst. Using our growth method, we synthesized Ge/graphene core/shell (Ge@G) NW and conducted it for highly thermal stability required devices. We confirm the existence of graphene shell and morphology of NWs using SEM, TEM and Raman spectra. SEM and TEM images clearly show very thin graphene shell. We annealed NWs in vacuum at high temperature. Our results indicated that surface melting phenomena of Ge NWs due to the high surface energy from curvature of NWs start around $550^{\circ}C$ which is $270^{\circ}C$ lower than bulk melting point. When we increases annealing temperature, tip of Ge NWs start to make sphere shape in order to reduce its surface energy. On the contrary, Ge@G NWs prevent surface melting of Ge NWs and no Ge spheres generated. Furthermore, we fabricated filed emission devices using pure Ge NWs and Ge@G NWs. Compare with pure Ge NWs, graphene protected Ge NWs show enhancement of reliability. This growth approach serves a thermal stability enhancement of semiconductor NWs.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.26-26
• /
• 2009

Vertically aligned arrays of mm-long multi-walled carbon nanotubes (MWCNTs) on Si substrates have been synthesized by water-assisted thermal chemical vapor deposition (CVD). The growth of CNTs was investigated by changing the experimental parameters such as growth temperature, growth time, gas composition, annealing time, catalyst thickness, and Al underlayer thickness. The 0.5-nm-thick Fe served as catalyst, underneath which Al was coated as a catalyst support as well as a diffusion barrier on the Si substrate. We grew CNTs by adding a little amount of water vapor to enhance the activity and the lifetime of the catalyst. Al was very good at producing the nm-size catalyst particles by preventing "Ostwald ripening". The Al underlayer was varied over the range of 15~40 nm in thickness. The optimum conditions for the synthesis parameters were as follows: pressure of 95 torr, growth temperature of $815^{\circ}C$, growth for 30 min, 60 sccm Ar + 60 sccm $H_2$ + 20 sccm $C_2H_2$. The water vapor also had a great effect on the growth of CNTs. CNTs grew 5.03 mm long for 30 min with the water vapor added while CNTs were 1.73 mm long without water vapor at the same condition. As-grown CNTs were characterized by using scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM), and Raman spectroscopy. High-resolution transmission electron microscopy showed that the as-grown CNTs were of ~3 graphitic walls and ~6.6 nm in diameter.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.393-393
• /
• 2012

Optically active nanostructures such as subwavelength moth-eye antireflective structures or surface enhanced Raman spectroscopy (SERS) active structures have been demonstrated to provide the effective suppression of unwanted reflections as in subwavelength structure (SWS) or effective enhancement of selective signals as in SERS. While various nanopatterning techniques such as photolithography, electron-beam lithography, wafer level nanoimprinting lithography, and interference lithography can be employed to fabricate these nanostructures, roll-to-roll (R2R) nanoimprinting is gaining interests due to its low cost, continuous, and scalable process. R2R nanoimprinting requires a master to produce a stamp that can be wrapped around a quartz roller for repeated nanoimprinting process. Among many possibilities, two different types of mask can be employed to fabricate optically active nanostructures. One is self-assembled Au nanoparticles on Si substrate by depositing Au film with sputtering followed by annealing process. The other is monolayer silica particles dissolved in ethanol spread on the wafer by spin-coating method. The process is optimized by considering the density of Au and silica nano particles, depth and shape of the patterns. The depth of the pattern can be controlled with dry etch process using reactive ion etching (RIE) with the mixture of SF6 and CHF3. The resultant nanostructures are characterized for their reflectance using UV-Vis-NIR spectrophotometer (Agilent technology, Cary 5000) and for surface morphology using scanning electron microscope (SEM, JEOL JSM-7100F). Once optimized, these optically active nanostructures can be used to replicate with roll-to-roll process or soft lithography for various applications including displays, solar cells, and biosensors.

• Journal of the Korean Chemical Society
• /
• v.29 no.5
• /
• pp.490-495
• /
• 1985

Novel palladium (II) complexes, $[Pd((ieaa)_2-en)]$ and [PdCl((ieaa)-l-pn)] ($(ieaa)_2-en)]$ and (ieaa)-l-pn denote N,N'-ethylenebis(isonitrosoethylacetoacetate imine) and l-N-(2-aminopropyl)-isonitrosoethylacetoacetate imine, respectively), have been prepared. The palladium (II) complexes were characterized on the bases of the electronic absorption, circular dichroism (CD), $^{13}C$ NMR, infrared, and Raman spectra. The reaction of palladium(II) cliloride and isonitrosoethylacetoacetate (ieaa) with methylenediamine gives an $(ieaa)_2-en)]$ type Schiff base, while similar reaction using l-propylenediamine instead of ethylenediamine gives an (ieaa)-l-pn type Schiff base. The difference in formation is discussed from the stereochemical viewpoint of the diamine employed.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.2
• /
• pp.141-148
• /
• 1999

High quality pure and Nb-doped $PbWO_{4}$ Single Crystal were grown from a 50 %~50 % mixture of Lead oxide (PbO) and Tungsten oxide $(WO_{3})$ by Czochralski method in Iridium crucible. The stoichiometric deviation correspond to the selective loss of the crystal constituents is found to be responsible for the yellowish coloration of $PbWO_{4}$. Through the X-ray powder diffraction experiment, we have investigated the lattice constant variations of each $PbWO_{4}$ crystals. We also present information on their photoluminescence (PL), optical absoption properties and Raman spectra. The temperature dependence of PL intensity and FWHM (Full Width Half Maximum) were measured in the temperature range 10 K~300 K. One observes a slight temperature dependence in the low temperature region and PL intensity decreases over 200 K by thermal quenching. The activation energy, Huang-Rhys coupling constant and inhomogenious brodenning acquired from their temperature dependence.

• Current Photovoltaic Research
• /
• v.2 no.1
• /
• pp.1-7
• /
• 2014

We developed a method of growing thin Si film at $600^{\circ}C$ by hot wire CVD using a very thin large-grained poly-Si seed layer for thin-film Si solar cells. The seed layer was prepared by crystallizing an amorphous Si film by vapor-induced crystallization using $AlCl_3$ vapor. The average grain size of the p-type epitaxial Si layer was about $20{\mu}m$ and crystallographic defects in the epitaxial layer were mainly low-angle grain boundaries and coincident-site lattice boundaries, which are special boundaries with less electrical activity. Moreover, with a decreasing in-situ boron doping time, the mis-orientation angle between grain boundaries and in-grain defects in epitaxial Si decreased. Due to fewer defects, the epitaxial Si film was high quality evidenced from Raman and TEM analysis. The highest mobility of $360cm^2/V{\cdot}s$ was achieved by decreasing the in-situ boron doping time. The performance of our preliminary thin-film solar cells with a single-side HIT structure and $CoSi_2$ back contact was poor. However, the result showed that the epitaxial Si film has considerable potential for improved performance with a reduced boron doping concentration.

• Current Photovoltaic Research
• /
• v.4 no.1
• /
• pp.16-20
• /
• 2016

$Cu_2ZnSnS_4$ (CZTS) thin films were fabricated by successive electrodeposition of layers of precursor elements followed by sulfurization of an electrodeposited Cu-Zn-Sn precursor. In order to improve quality of the CZTS films, we tried to optimize the deposition condition of absorber layers. In particular, I have conducted optimization experiments by changing the Cu-layer deposition time. The CZTS absorber layers were synthesized by different Cu-layer conditions ranging from 10 to 16 minutes. The sulfurization of Cu/Sn/Zn stacked metallic precursor thin films has been conducted in a graphite box using rapid thermal annealing (RTA). The structural, morphological, compositional, and optical properties of CZTS thin films were investigated using X-ray diffraction (XRD), Field emission scanning electron microscopy (FE-SEM), Raman spectroscopy, and X-ray Flourescenece Spectrometry (XRF). Especially, the CZTS TFSCs exhibits the best power conversion efficiency of 4.62% with $V_{oc}$ of 570 mV, $J_{sc}$ of $18.15mA/cm^2$ and FF of 45%. As the time of deposition of the Cu-layer to increasing, the properties were confirmed to be systematically changed. And we have been discussed in detail below.

• Carbon letters
• /
• v.24
• /
• pp.97-102
• /
• 2017

Graphite fibers are materials with a high specific modulus that have attracted much interest in the aerospace industry, but their high manufacturing cost and low yield are still problems that prevent their wide applications in practice. This paper presents a laser-based process for graphitization of carbon fiber (CF) and explores the effect of laser radiation on the microstructure of CF. The obtained Raman spectra indicate that the outer surface of CF evolves from turbostratic structures into a three-dimensional ordered state after being irradiated by a laser. The X-ray diffraction data revealed that the growth of crystallite was parallel to the fiber axis, and the interlayer spacing $d_{002}$ decreased from 0.353 to 0.345 nm. The results of scanning electron microscopy revealed that the surface of irradiated CFs was rougher than that of the unirradiated ones and there were scale-like small fragments that had peeled off from the fibers. The tensile modulus increased by 17.51% and the Weibull average tensile strength decreased by 30.53% after being irradiated by a laser. These results demonstrate that the laser irradiation was able to increase the graphitization degree of the CFs, which showed some properties comparable to graphite fibers.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.222.2-222.2
• /
• 2016

트랜지스터 응용 등에 관한 연구가 활발해 지면서 에너지 밴드갭이 0 eV에 가까운 그래핀 이외의 밴드 갭 조절이 가능한 MoS2 (molybdenum disulfide), BN (boron nitride), Bi2Te3 (bismuth telluride), WS2 (tungsten disulfide) 등과 같은 이차원 Transition Metal DiChalcogenides (TMDC) 물질이 반도체 물질로 각광받고 있다. 특히 MoS2의 경우 단결정 덩어리 상태에서는 약 1.3 eV의 밴드갭을 가지나 두께가 줄어들어 두 층일 경우에는 약 1.65 eV, 단일층이 되면 약 1.9 eV의 밴드갭을 가져 박막 층수에 따라 에너지 밴드갭 조절이 가능한 것으로 알려져있다. 하지만 두께 조절이 가능하면서 대면적, 고품질을 가지는 MoS2 박막 합성은 아직 제한적이라 할 수 있으며 새로운 방법 및 물질에 대한 연구가 지속적으로 이루어 지고 있다. 따라서 본 연구에서는 다양한 층수를 지니는 MoS2 합성을 위해 나노 두께의 MoS2 박막을 CF4 plasma 를 이용하여 layer etching 진행하고 CF4 plasma 100초 etching 진행한 2 layer 두께의 MoS2를 기준으로 H2S plasma를 이용하여 treatment 진행하였다. 물리적, 화학적 분석은 Raman spectroscopy, XPS(X-ray Photoelectron Spectroscopy), AFM (Atomic Force Microscopy) 등을 이용해 진행하였고 이를 통해 MoS2 layer 감소 및 damage recovery 등을 확인하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.375.2-375.2
• /
• 2016

그래핀(Graphene)은 원자 한 층 두께의 얇은 특성에 기인하여 우수한 투과도(~97.3%)를 나타내며, 높은 전자 이동도($200,000cm^2V^{-1}s^{-1}$)로 인하여 전기 전도도가 우수한 2차원 전자소재이다. 또한 유연하고 우수한 기계적 물성을 가지고 있어 실제로 다양한 소자에서 활용되고 있다. 그래핀을 이용하여 다양한 소자로 응용하기 위한 과정 중 하나인 포토리소그래피 공정(Photolithography process)은 원하는 패턴을 만들기 위해 제작하고자 하는 기판 위에 포토레지스트(Photoresist)를 코팅하는 과정을 거치게 된다. 하지만 이러한 과정은 소자 제작에 있어서 포토레지스트 잔여물을 남기게 된다. 그래핀 위에 남은 포토레지스트 잔여물은 그래핀의 우수한 전기적 특성을 저하시켜 소자특성에 불이익을 주게 된다. 본 연구에서는 수소 플라즈마를 이용하여 그래핀 위에 남은 중합체(Polymer) 잔여물을 제거한다. 사용한 그래핀은 화학 기상 증착법(Chemical vapor deposition)을 이용하여 성장시켰으며, PMMA(Poly(methyl methacrylate))를 이용하여 이산화규소(silicon dioxide) 기판에 전사하였다. 그래핀의 손상 없이 중합체 잔여물을 제거하기 위해 플라즈마 처리시간을 15초부터 1분까지 늘려가며 연구를 진행하였으며, 플라즈마 처리 시간에 따른 중합체 잔여물의 제거 정도와 그래핀의 보존 여부를 확인하기 위해 라만 분광법(Raman spectroscopy)과 원자간력현미경(Atomic force microscopy)을 사용하였다. 본 연구 결과를 통해 간단한 플라즈마 처리로 보다 나은 특성의 그래핀 소자를 얻게 됨으로써, 향상된 특성을 가진 그래핀 소자로 산업적 응용 가능성을 높일 수 있을 것이라 생각된다.