• 신재생에너지
• /
• 제10권1호
• /
• pp.6-19
• /
• 2014

Organic Rankine cycle (ORC) has been widely used to convert renewable energy such as solar energy, geothermal energy, or waste energy etc., to electric power. For a small scale output power less than 10 kW, turbo-expander is not widely used than positive displacement expander. However, the turbo-expander has merits that it can operate well at off-design points. Usually, the available thermal energy for a small scale ORC is not supplied continuously. So, the mass flowrate should be adjusted in the expander to maintain the cycle. In this study, nozzles was adopted as stator to control the mass flowrate, and radial-type turbine was used as expander. The turbine operated at partial admission. R245fa was adopted as working fluid, and supersonic nozzle was designed to get the supersonic flow at the nozzle exit. When the inlet operating condition of the working fluid was varied corresponding to the fluctuation of the available thermal energy, optimal operating condition was investigated at off-design due to the variation of mass flowrate.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제36회 춘계학술대회논문집
• /
• pp.61-65
• /
• 2011

본 연구에서는 초음속 충동형 터빈의 노즐에서 나타나는 유동의 과소 과대팽창 문제를 최적화 기법을 이용하여 비대칭형상을 포함해 설계함으로써 개선시키고자 하였다. 노즐 형상 설계를 위해 8개의 설계변수를 설정하였으며 목적함수로는 후류 영역 출구까지의 정효율이 최대가 되도록 하였다. 최적화에는 iSIGHT-FD가 사용되었으며 근사최적화를 위한 방법으로는 Radial Basis Function을 이용하였다. 노즐유동의 계산에는 상용 코드인 FLUENT 6.3을 사용하였으며 개선된 노즐의 정효율은 기존 대비 1.35% 증가하였고 손실계수는 19.85% 감소하였다.

• 한국유체기계학회 논문집
• /
• 제17권6호
• /
• pp.38-43
• /
• 2014

In Ocean, the temperature of the deep sea water is always lower than that of the surface sea water. The temperature difference between the surface water and deep sea water is about $20^{\circ}C$. Based on thermodynamics, this temperature difference can be converted into mechanical power. The mechanical power can be converted to electricity through a generator. However, the temperature difference is relatively small compared with that of traditional steam turbines. It is difficult to apply the steam turbine technology for this small temperature difference directly. Therefore, the turbine for OTEC system using low temperature difference should be designed to meet the system requirement. The present study focuses on the development of the turbine for 20 kW OTEC system using R32. The paper includes the determination of working fluids, meridional design, turbine layout and 3D CFD results. With off-design points analysis, the full performance of 20kW OTEC turbine is investigated. Through the research, one stage radial type turbine with R32 as working fluid is successfully developed and can be applied to other high temperature heat source.

• 한국해양공학회지
• /
• 제28권4호
• /
• pp.314-323
• /
• 2014

In this study, a gearbox and blade were modeled in the MASTA program, and the housing and carrier components were modeled using a finite element method. Using substructure synthesis, all the components were combined and used to establish a vibration model of a 2.5-MW wind turbine gearbox. In addition, the safety displacement factor was evaluated using an AGMA data sheet about bearing's outer race for the input shaft and output shaft. As a result, the bearing's outer race for the input shaft, and the radial and axial responses were satisfied by the $1^{st}$ and $2^{nd}$ planetary gears and the $3^{nd}$ helical gear transmission error(TE), respectively. However, the output shaft support bearing's outer race responses were not satisfied with the radial response by the $2^{nd}$ TE and axial response by the $3^{rd}$ TE. To reduce the vibration, tooth modification was needed. After profile tooth modification, at the outer race of the output shaft support bearing, the radial response was reduced by approximately $20{\mu}m$, and the axial response was reduced by approximately $6{\mu}m$.

• 대한기계학회논문집B
• /
• 제38권12호
• /
• pp.1057-1064
• /
• 2014

최근 전세계적으로 재생에너지의 관심이 증가하고 있다. 그 중 많은 관심을 받고 있는 것이 상대적으로 낮은 온도의 폐열을 사용하는 유기랭킨사이클(ORC)이다. 유기랭킨사이클은 기존의 증기터빈사이클과 유사한 기술을 사용하지만 낮은 온도의 폐열을 사용하기 위해서 증기대신 냉매를 작동유체로 사용한다. 작동유체를 냉매로 사용함으로 인해 이상기체 가정을 사용할 수 없고, 이는 ORC 시스템에 이용되는 터빈의 설계를 좀 더 복잡하게 만든다. 또, 냉매의 큰 분자량과 복잡한 분자구조로 인하여 낮은 음속을 가지게 되고 이로 인해서 쉽게 초킹 조건에 접근하게 된다. 본 연구에서 R245fa를 작동유체로 하여 입구온도 $124^{\circ}$에 팽창비 9 의 조건에서 터빈의 효율을 증가시키기 위해 다단으로 설계된 아음속 ORC 터빈을 설계하는 과정과 터빈의 성능에 대하여 설명하고자 한다. 설계된 터빈은 200kW 급의 ORC 발전 시스템에 사용될 예정이다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.387-391
• /
• 2011

Since MEMS based micro actuators or generating devices have high efficiency per volume, plenty of research are ongoing. Among them, MEMS based millimeter-scale micro gas' turbine is one of the most powerful issue for replacing chemical batteries. However, since limiting of MEMS manufacturing technique, it is very difficult that makes wide turbine bearing area. It causes low DN number, so sufficient bearing force is hard to achieve. Thus, the most important issue on micro gas turbine is proper bearing design which can keep rotor stable during operation. In order to that, micro-scale gas-lubricated bearing is generally used. In this paper, basic feasibility study and design of journal bearing for 10mm diameter micro gas turbine is described Journal bearing is hydrostatic gas-lubricated type. Numerical simulation is performed with ANSYS CFX 11.0 which is commercial numerical tool. Repulsive force when there is radial displacement in bearing and returning time is calculated using steady and unsteady cases. Auto re-meshing technic is used for moving mesh unsteady cases which simulate displacement of axis and its movement. The simulation results are used for further design of micro gas turbine, and experiment will be done later.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권10호
• /
• pp.1225-1231
• /
• 2014

This paper presents the performance characteristic of a Francis hydro turbine with an inline casing. This turbine is designed for city water supply system. Due to large changes in ground elevation with high points and low points, some systems may experience larger-than-normal required pressures in areas with low ground elevations. One way to dissipate these excess pressures is by the use of an inline-turbine instead of an inline-pressure reducing valve. For best applicability and minimal space consumption, the turbine is designed with an inline casing instead of the common spiral casing. As a characteristic of inline casing, the flow accesses to the runner in the radial direction, showing a low efficiency. The installation of vanes improves the internal flow and gives the positive encouragement to the output power. For the power transmission to the outside of the turbine casing from the runner axis, a belt passage is designed in the inline casing, as its influence, the region after the belt passage shows a relatively low output power. The clearance gap in the runner side space is considered, in which a small volume of flow is contracted into the clearance gap, forming the leakage flow. The leakage flow leads to a decrease in the efficiency.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 춘계학술대회 초록집
• /
• pp.61.2-61.2
• /
• 2011

The spanwise aerodynamic loads of the wind turbine blade are investigated numerically. The blade shape such as twist and chord length along the blade span is obtained from the procedure of aerodynamically optimal design. The rated tip speed ratio and the rated wind velocity are set to 7 and 12m/s respectively. The BEM method is applied to obtain both the aerodynamic performance of the wind turbine (Fig.1) and the spanwise aerodynamic loads along the blade span including Prandtl's tip loss factor. The maximum running power coefficient is occurred around 90% radial position from hub (Fig.2). The distributed aerodynamic loads along the blade span can be used for structure analysis.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2000년도 유체기계 연구개발 발표회 논문집
• /
• pp.211-218
• /
• 2000

Off-design experimental performance was investigated for a small centrifugal compressor, whose impeller diameter is about 125mm, used in an industrial gas turbine. Test rig was designed and manufactured with a radial inflow turbine and a combustor to supply driving power to the compressor. Static pressure was measured on the casing of the impeller, vaneless diffuser, vaned diffuser and volute. Total pressure was obtained using specially fabricated rakes at the vaned diffuser throat and exit. Circumferential nonuniformity was found, near surge, in the Impeller, vaned diffuser and volute region. Spanwise nonuniform flow from the impeller affected the total pressure defects in the vaned diffuser region. Static pressure distortion in the circumferential direction in the volute was found near surge, where the minimum occurred near 140 degree position.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.670-675
• /
• 2001

This paper describes aerodynamic preliminary design performance prediction and flow analysis for turbine of the marine middle engine turbocharger. The performance characteristics of turbocharger turbine are investigated at various operating conditions using mass flow rate and computational flow analysis for rotor and nozzle at design point are performed. Preliminary design results are performed by applying mean line and radial equilibrium theory. Performance prediction and flow analysis results show good agreement with experiments. From 3 dimensional flow analysis result, efficiency is 0.6% greater than design point. Therefore, this design approach is useful for preliminary design, and helps to increase the design capability for optimized rotor blade.